Creda TIDN24P001 User manual
ContactDetails
Pleasenotethatsomeofthecontactdetailson
thisPDFdocumentmaynotbecurrent.
Pleaseusethefollowingdetailsifyouneedto
contactus:
Telephone:08448793588
Email:[email protected]
TheHelpCentresectionofthiswebsitealsofeaturesawiderange
ofinformationwhichmaybeofusetoyouandisavailable24
hoursaday.Itincludes:
•Operatingandinstallationinstructionsdownloads
•Requestarepair
•Wheretobuyourproducts
•Literaturedownloads
•Heatingrequirementcalculator
www.credaheating.co.uk/help‐centre
A division of GDC Group Ltd
Millbrook House Grange Drive Hedge End Southampton SO30 2DF
www.credaheating.co.uk
Re
g
istered No: 1313016 En
g
land
VAT GB 287 1315 50004
EEE Producer Registration Number –
WEE/GE0057TS
Paper from sustainable sources
24 Hour Timer
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Installation
Switch the heater off and remove the plug-in protective cover
from the right hand side of the thermostat unit at the back of
the heater. Remove the 24-hour plug in timer from its box and
plug it into the slide in compartment now exposed. Switch the
heater on at the mains supply.
Mode Selection
There are three different operating modes. Press MODE to
cycle through these:
MAN OFF - heating is
permanently Off – see
Fig. 1.
This is also the default
screen.
MAN ON - heating is
permanently On - see
Fig. 2.
AUTO - runs the
programmed times - see
Fig. 3.
Set Time
Press the PROG key
once to set time. The
appears on the screen
(seeFig. 4)andthehours
can be set using the
keys. Press ENTER
when finished setting the
hours. Set minutes using
the keys and press
ENTER.
Time is now set.
MODE PROG ENTER
12:13
MAN OFF
Fig. 1
MODE PROG ENTER
12:13
MAN ON
Fig. 2
MODE PROG ENTER
00:00
AUTO ON
Fig. 3
MODE PROG ENTER
00:00
MAN OFF
Fig. 4
Set Program
A maximum of four
program periods can be
set as follows;
Press PROG twice (see
Fig. 5). The program
settings can now be
entered (starting with P1
ON, where P1 ON is the
first ON time setting).
a) set P1 ON time:
Set the hours using and press ENTER. Then set the
minutes using and press ENTER.
NOTE: Time is set in 10 minute blocks.
Then set P1 OFF time:
Set the hours using and press ENTER.
Then set the minutes using and press ENTER. If only
one program is required, press PROG now to return to default
display OR
b) set P2 ON and OFF times: repeat procedure as ‘a)’ above.
c) set P3 ON and OFF times: repeat procedure as ‘a)’ above.
d) set P4 ON and OFF times: repeat procedure as ‘a)’ above.
After programming P4 the default screen is automatically
displayed. To leave program settings unchanged press
ENTER continually.Atanytime during programming, pressing
PROG will exit to the default display.
Timer must be in AUTO mode to run Set Programs.
Key Lock
To lock the keypad press
ENTER andrelease, then
press MODE within 1
second (see Fig. 6). The
key symbol will appear
on the screen when the
keypad is locked.
To unlock the keypad
repeat the action above.
Ifanyofthebuttonsonthe
keypadarepressedwhen
it is locked, the light will automatically come on.
The Advance Function
WheninAUTOmode,if ispressedforlongerthan2seconds
the program will advance to the next programmed setting.
When the ADVANCE function is active ADVANCE will be
displayed on the screen (see Fig. 7).
To cancel advance press for longer than 2 seconds e.g. If
present time is 14:00 and
P1 ON is at 17:00 and P1
OFF is 19:00, if is held
for 2 seconds then
ADVANCE appears on
the screen. The heater
comesonand remains on
until 19:00. ADVANCE
disappears from the
screen at 17:00 as set
program is then running.
MODE PROG ENTER
00:00
AUTO
ON
P1
Fig. 5
MODE PROG ENTER
00:00
MAN OFF
Fig. 6
MODE PROG ENTER
00:00
ON
AUTO
ADVANCE
Fig. 7
Installation and Operating Instructions
TIDN24P001 Issue 1
