Crestron 3 Series Owner's manual

PRO3
3-Series Control System®
Supplemental Guide
Crestron Electronics, Inc.

Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive,
non-transferable Software Development Tools License Agreement. Crestron product operating system software is licensed to Crestron
dealers, CSPs, and end-users under a separate End-User License Agreement. Both of these Agreements can be found on the Crestron
website at www.crestron.com/legal/software_license_agreement.
A portion of the code in this product is covered by the Microsoft®Public License (Ms-PL), which can be found at
www.microsoft.com/opensource/licenses.mspx.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, 3-Series Control System, Cresnet, and Crestron Toolbox are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be
used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary
interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.

Contents
Introduction 1
Configuration 1
About ...................................................................................................................... 2
Ethernet Settings..................................................................................................... 2
LAN ........................................................................................................... 2
Control Subnet........................................................................................... 5
DNS Servers .............................................................................................. 7
Advanced Settings ..................................................................................... 8
MyCrestron ................................................................................................ 9
Ethernet Diagnostics ................................................................................ 10
Application Settings .............................................................................................. 11
Register and Unregister Programs ........................................................... 11
Start and Stop Programs ......................................................................... 11
IP Table.................................................................................................... 12
Comments ............................................................................................... 12
I/O Control ............................................................................................................ 12
IR Ports.................................................................................................... 12
Relays ...................................................................................................... 13
Versiports................................................................................................. 13
Com Ports ............................................................................................... 13
Diagnostics ........................................................................................................... 15
Reboot.................................................................................................................. 15
Screen Setup ........................................................................................................ 16
Brightness................................................................................................ 16
Timeout.................................................................................................... 16
Supplemental Guide – DOC. 7330D Contents •i

PRO3: 3-Series Control System®
Introduction
The PRO3’s Nav Pad and LCD display can be used to configure and monitor the PRO3’s
operations.
Alternatively, Crestron Toolbox™ and the PRO3’s built-in web interface can also be used.
For details, refer to the Crestron Toolbox help file and the AV3/PRO3 DO Guide (Doc. 7721)
at www.crestron.com/manuals.
Configuration
Press
HOME
to display the
Main Menu
, shown below.
Main Menu
The
Main Menu
is divided into seven sections:
•
About
displays the controls system’s IP address, hostname, MAC address, and
firmware information.
•
Ethernet Settings
configures and displays the PRO3’s Ethernet settings.
•
Application Settings
selects a program to register, run or stop, and provides
information about the selected program.
•
IO Control
monitors and operates the PRO3’s input and out ports.
•
Diagnostics
displays information about the connected devices, hardware
configuration, and error logs.
•
Reboot
provides controls for rebooting the PRO3.
•
Screen
Setup
configures the front panel display.
Press up or down on the Nav Pad to highlight the desired selection, and then press the
center button of the Nav Pad to select it. Press
HOME
at any time to return to the
Main
Menu
. Press
BACK
at any time to return to the previous screen.
Main Menu
About
Ethernet Settings
Application Settings
IO Control
Diagnostics
Supplemental Guide – DOC. 7330D PRO3: 3-Series Control System •1

About
Select
About
to display the
About
menu. The
About
menu displays the PRO3’s IP address,
hostname, MAC address and firmware details.
About Menu
To view firmware details, press up or down on the Nav Pad to highlight
Firmware Details
,
and then press the center button of the Nav Pad.
To cancel and return to the previous menu, press
BACK
.
Ethernet Settings
Select
Ethernet Settings
to display the
Ethernet Settings
menu. The
Ethernet Setings
menu displays the status of the Ethernet connection (
Link
, green indicates active) and
provides options to view and configure settings for the LAN connection, the control subnet,
DNS servers, ports, webserver, SSL, MyCrestron, and Ethernet Diagnostics. Press up or
down on the Nav Pad to highlight the desired selection, and then press the center button of
the Nav Pad to select it.
Ethernet Settings Menu
LAN
Select
LAN
from the
Ethernet Settings
menu to edit settings for the LAN connection. The
LAN Settings
menu is displayed.
If any changes are made, the PRO3 must be rebooted. For details on rebooting the PRO3,
refer to “Reboot” on page 15.
About
IP Address: 172.30.16.25
Hostname: PRO3-7F28F5E6
MAC Address: 00:10:7e:26:f6:c3
Firmware Version: v1.010.0060
Firmware Details
Ethernet Settings
LAN
Link
Control Subnet
DNS Servers
Advanced Settings
MyCrestron
2•PRO3: 3-Series Control System Supplemental Guide – DOC. 7330D

LAN Settings Menu
Select
Current Settings
to view the current settings, or select
Static Settings
to manually
change the settings.
Current Settings
Selecting
Current Settings
displays the settings for DHCP operation, hostname, IP
address, subnet mask, default router, and domain name.
Static Settings
Selecting
Static Settings
allows editing of the DHCP settings, host name, IP address,
subnet mask, default router, and domain name.
Static Settings Screen
•
DHCP
changes the setting for DHCP operation. The PRO3 can obtain an IP
address, a subnet mask, and the default router information from a DHCP server.
To enable or disable DHCP, press up or down on the Nav Pad to highlight
DHCP:
On
or
DHCP: Off
, and then press the center button of the Nav Pad. The setting
toggles between
On
and
Off
. The default setting is
DHCP: On
.
•
HostName
shows the PRO3’s hostname. Highlight the hostname, and then press
the center button of the Nav Pad to change it.
Edit Host Name Screen
oUse the left and right buttons on the Nav Pad to select a character to
change.
LAN Settings
Current Settings
Static Settings
About
DHCP: ON
Hostname: PRO3-7F28F5E6
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Def Router: 0.0.0.0
Edit Host Name
[P]RO3-7625E3F
Press ‘Select’ to Save or ‘BACK’ to Cancel.
Press and Hold ‘Left’ to Delete.
Press and Hold ‘Right’ to Insert.
Supplemental Guide – DOC. 7330D PRO3: 3-Series Control System •3

oUse the up and down buttons on the Nav Pad to browse the list of possible
characters.
oPress and hold the left button on the Nav Pad to delete a character.
oPress and hold the right button on the Nav Pad to insert a character.
oPress the center button of the Nav Pad to save the new hostname.
oPress
BACK
to cancel.
•
IP Address
shows the IP address 0.0.0.0. Highlight the IP address, and then press
the center button of the Nav Pad to change it.
Edit IP Address Screen
1. Press up or down on the Nav Pad to set the first octet of the IP address.
2. Press left or right on the Nav Pad to move the cursor between octets and
select one for editing.
3. Set each octet until the correct IP address is displayed.
4. To save the IP address and return to the previous screen, press the center
button of the Nav Pad. To cancel the operation and return to the previous
screen, press
BACK
.
•
Subnet Mask
shows the subnet mask address 0.0.0.0. Highlight the subnet mask,
and then press the center button of the Nav Pad to change it.
Edit Subnet Mask Screen
1. Press up or down on the Nav Pad to set the first octet of the subnet mask.
2. Press left or right on the Nav Pad to move the cursor between octets and
select one for editing.
3. Set each octet until the correct subnet mask is displayed.
4. To save the subnet mask and return to the previous screen, press the center
button of the Nav Pad. To cancel the operation and return to the previous
screen, press
BACK
.
Edit IP Address
[0].0.0.0
Press ‘Select’ to Save or ‘BACK’ to Cancel.
Edit Subnet Mask
[0].0.0.0
Press ‘Select’ to Save or ‘BACK’ to Cancel.
4•PRO3: 3-Series Control System Supplemental Guide – DOC. 7330D

•
Def Router
shows the default router address 0.0.0.0. Highlight the default router,
and then press the center button of the Nav Pad to change it.
Edit Default Router Screen
1. Press up or down on the Nav Pad to set the first octet of the default router.
2. Press left or right on the Nav Pad to move the cursor between octets and
select one for editing.
3. Set each octet until the correct default router is displayed.
4. To save the default router and return to the previous screen, press the center
button of the Nav Pad. To cancel the operation and return to the previous
screen, press
BACK
.
•
Domain
shows the domain name crestron.crestron.com. Highlight the default
router, and then press the center button of the Nav Pad to change it.
Edit Domain Name Screen
1. Press up or down on the Nav Pad to set the first octet of the default router.
2. Press left or right on the Nav Pad to move the cursor between octets and
select one for editing.
3. Set each octet until the correct default router is displayed.
4. To save the default router and return to the
LAN Static Settings
menu, press
the center button of the Nav Pad. To cancel the operation and return to the
previous screen, press
BACK
.
Control Subnet
Select
Control Subnet
from the
Ethernet Settings
menu to view and edit settings for the
control subnet connection. The
Control Subnet
menu displays the status of the control
subnet connection (
Link
, green indicates active) and provides information and configuration
options for the MAC address (information only), IP address (information only), routing prefix
(automatic or manually set), and port forwarding (information only). Press up or down on the
Nav Pad to highlight the desired selection, and then press the center button of the Nav Pad
to select it.
Edit Default Router
[0].0.0.0
Press ‘Select’ to Save or ‘BACK’ to Cancel.
Edit Domain Name
[C]RESTRON.CRESTRON.COM
Press ‘Select’ to Save or ‘BACK’ to Cancel.
Press and Hold ‘Left’ to Delete.
Press and Hold ‘Right’ to Insert.
Supplemental Guide – DOC. 7330D PRO3: 3-Series Control System •5

If any changes were made, the PRO3 must be rebooted. For details on rebooting the
PRO3, refer to “Reboot” on page 15.
Control Subnet Menu
Select
Current Settings
to view the current settings or select
Static Settings
to manually
change the settings.
Automatic Mode
Automatic mode determines if the control system will automatically configure a routing prefix
or if a routing prefix is to be entered manually.
Press up or down on the Nav Pad to highlight
Automatic Mode: On
, and then press the
center button of the Nav Pad. A new screen is displayed, prompting the user to enter a
routing prefix. Refer to “Routing Prefix” below for details on setting the routing prefix.
Automatic mode turns off when the routing prefix is saved. If Automatic mode is off and the
center button of the Nav Pad is pressed, the mode turns on after a brief pause for the
system to update.
Routing Prefix
Edit the routing prefix by pressing up or down on the Nav Pad to highlight
Routing Prefix
,
and then press the center button of the Nav Pad. For details on using routing prefixes, refer
to the “IP Considerations Guide for the IT Professional Design Guide”, (Doc. 4579) at
www.crestron.com/manuals.
NOTE:
If the Automatic mode is on, the routing prefix cannot be changed.
Edit Routing Prefix Screen
1. Press up or down on the Nav Pad to set the first octet of the routing prefix.
2. Press left or right on the Nav Pad to move the cursor between octets and
select one for editing.
3. Set each octet until the correct routing prefix is displayed.
Control Subnet
MAC Address: 00:10:7e:26:3c:b6
Link
IP Address: 10.0.0.1
Automatic Mode: On
Routing Prefix
Port Forwarding
Edit Routing Prefix
[0].0.0.0/0
Press ‘Select’ to Save or ‘BACK’ to Cancel.
6•PRO3: 3-Series Control System Supplemental Guide – DOC. 7330D