CP4-R
4-Series™ Control System for Crestron Home™ OS
Product Information - 8547B
(2054636)
11.21
Getting Started
Scan the QR code to view the Quick Start Guide.
www.crestron.com/docs/8415
For additional information on the Crestron® CPR-4, visit
www.crestron.com/model/6512254.
Pair with Apple® HomeKit® Technology
The CP4-R can be paired with Apple® HomeKit® technology to enable
communication between the Crestron Home™ OS system and Apple
HomeKit devices and accessories.
To pair the CP4-R with an Apple HomeKit system, open the Apple
Home app on an iOS® device, and then use the device camera to scan
the QR code provided below.
NOTE: Be sure to scan the QR code with an iOS device that is
associated with the homeowner’s Apple ID, as the Crestron Home
system is paired to the Apple ID associated with the chosen iOS
device.
lFor more information on pairing the device with an Apple HomeKit
system, refer to https://support.apple.com/en-us/HT204893.
lFor more information on integrating Crestron Home with Apple
HomeKit devices, refer to the Crestron Home OS™ Product
Manual at docs.crestron.com/en-us/8525/.
NOTE:The above QRcode is unique to the device that shipped with
this document.
Certification and Compliance
Regulatory Model: M201903003
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is
subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
lReorient or relocate the receiving antenna.
lIncrease the separation between the equipment and receiver.
lConnect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
lConsult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
As of the date of manufacture, the product has been tested and
found to comply with specifications for CE marking.
This product is Listed to applicable UL® Standards and requirements
tested by Underwriters Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL
applicables par Underwriters Laboratories Inc.
Rack Mounting Safety Precautions
Elevated Operating Ambient Temperature: If installed in a closed or
multi-unit rack assembly, the operating ambient temperature of the
rack environment may be greater than room ambient temperature.
Therefore, consideration should be given to installing the equipment
in an environment compatible with the maximum ambient
temperature (Tma) specified by the manufacturer.
Reduced Airflow: Installation of the equipment in a rack should be
such that the amount of airflow required for safe operation of the
equipment is not compromised.
Mechanical Loading: Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven
mechanical loading.
Circuit Overloading: Consideration should be given to the connection
of the equipment to the supply circuit and the effect that
overloading of the circuits might have on overcurrent protection and
supply wiring. Appropriate consideration of equipment nameplate
ratings should be used when addressing this concern.
Reliable Earthing: Reliable earthing of rack-mounted equipment
should be maintained. Particular attention should be given to supply
connections other than direct connections to the branch circuit (e.g.,
use of power strips).
Legal
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. for specific
information, visit www.crestron.com/opensource.
Crestron, the Crestron logo, 4-Series, and Crestron Home are either
trademarks or registered trademarks of Crestron Electronics, Inc., in
the United States and/or other countries. Apple and HomeKit are
either trademarks or registered trademarks of Apple, Inc. in the
United States and/or other countries. iOS is either a trademark or a
registered trademark of Cisco Systems, Inc. in the United States
and/or other countries. UL and the UL logo are either trademarks or
registered trademarks of Underwriters Laboratories, Inc. in the
United States and/or other countries. Other trademarks, registered
trademarks, and trade names may be used in this document to refer
to either the entities claiming the marks and names or their products.
Crestron disclaims any proprietary interest in the marks and names
of others. Crestron is not responsible for errors in typography or
photography.
©2021 Crestron Electronics, Inc.
