Crestron FT-TSC600 FlipTop Owner's manual

FT-TSC600
FlipTop™ Touch Screen Control System
Supplemental Guide
Crestron Electronics, Inc.

Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive,
non-transferable Software Development Tools License Agreement. Crestron product operating system software is licensed to Crestron
dealers, CSPs, and end-users under a separate End-User License Agreement. Both of these Agreements can be found on the Crestron
website at www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, 3-Series, Cresnet, Crestron Toolbox, FlipTop, and Rava are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. Internet Explorer is either a trademark or registered trademark of
Microsoft Corporation in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in
this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the
marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.

Contents
Access the Setup Screens 1
Configure the FT-TSC600 2
Ethernet Setup ........................................................................................................ 2
Edit the Hostname ..................................................................................... 3
Edit the IP Address .................................................................................... 3
Edit Additional Ethernet Parameters........................................................... 4
Edit the Advanced Settings ........................................................................ 4
Edit the Ethernet Diagnostics ..................................................................... 6
Edit the MyCrestron Dynamic DNS Settings............................................... 7
Audio Setup ............................................................................................................ 7
Display Setup.......................................................................................................... 8
Application Setup.................................................................................................... 8
Standby Timeout..................................................................................................... 9
Diagnostics ............................................................................................................. 9
Keypad Test............................................................................................. 10
Touch Test............................................................................................... 10
RAVA ....................................................................................................... 11
Test Patterns............................................................................................ 11
Calibrate .................................................................................................. 11
About .................................................................................................................... 12
Save & Edit ........................................................................................................... 12
Supplemental Guide – DOC. 7593C Contents •i

FT-TSC600: FlipTop Touch Screen
Control System
Access the Setup Screens
The
FT-TSC600 Setup
screen is the starting point for configuring the TF-TSC600 FlipTop™
Touch Screen Control System from Crestron®.
NOTE:
If no project has been loaded or if an invalid project has been loaded, the screen
displays the following message: “There is no display project to start. [Touch Screen to Enter
Setup…].”
The setup screens enable basic configuration prior to regular operation of the touch screen.
During regular operation of the touch screen, there are two ways to access the setup
screens:
1. Place a button on the project main page and assign the reserved join number
(17242) that accesses the setup screens.
2. Press hard keys 1, 2, 3, and 4, to the right of the touch screen display in sequence
twice (i.e., press 1, 2, 3, 4, 1, 2, 3, 4) within a 5 second period.
Button Numbering
4
3
2
1
Supplemental Guide – DOC. 7593C FT-TSC600: FlipTop Touch Screen Control System •1

The
FT-TSC600 Setup
screen is displayed.
FT-TSC600 Setup Screen
The
FT-TSC600 Setup
screen is comprised of buttons for Ethernet setup, audio setup,
display setup, application setup, standby timeout, and diagnostics. In addition, there is an
About
button that provides information about the touch screen and a
Save & Exit
button.
The functions of each are detailed in the following pages of this guide.
Configure the FT-TSC600
Ethernet Setup
On the
FT-TSC600 Setup
screen, tap
Ethernet Setup
to display the
Ethernet Setup
screen.
Ethernet Setup Screen
The
Ethernet Setup
screen displays current settings, such as whether DHCP is on or off,
the touch screen’s hostname, and its IP address. This screen also contains a link indicator
to show the status of the Ethernet connection. Controls on this screen are explained in the
sections that follow.
2•FT-TSC600: FlipTop Touch Screen Control System Supplemental Guide – DOC. 7593C

Edit the Hostname
To edit the hostname, tap
Edit
. The
Edit Hostname
screen opens.
Edit Hostname Screen
Use the keyboard to enter the new name. Tap
Clear
to clear a previous entry,
Save
to save
a new entry, or
Cancel
to return to the previous screen.
Edit the IP Address
To edit the IP address, tap
Edit
. The
Edit IP Address
screen opens.
Edit IP Address Screen
Use the keyboard to enter the new IP address. Tap
Clear
to remove a previous entry,
Backspace
to delete the last digit,
Enter
to save a new entry, or
Cancel
to return to the
previous screen.
Supplemental Guide – DOC. 7593C FT-TSC600: FlipTop Touch Screen Control System •3

Edit Additional Ethernet Parameters
Tap the ellipsis (
…
) at the top of the
Ethernet Setup
screen to display additional Ethernet
parameters and the controls that allow their entry.
Ethernet Setup Screen (Additional Parameters)
To edit the subnet mask, default router, or domain, tap the corresponding
Edit
button and
use the keyboard to enter the new information.
After all new settings have been entered, tap
Reboot
at the bottom of the
Ethernet Setup
screen to reboot the touch screen so the new settings can take effect.
Edit the Advanced Settings
Tap
Advanced Settings
to display the
Advanced Ethernet Setup
screen.
Advanced Ethernet Setup Screen
The
Advanced Ethernet Setup
screen provides controls for enabling or disabling SSL
(Secure Sockets Layer) and for editing the CIP port, secure CIP port, CTP port, and secure
CTP port.
4•FT-TSC600: FlipTop Touch Screen Control System Supplemental Guide – DOC. 7593C

The SSL controls work as follows:
•
Off
disables the SSL capabilities of the FT-TSC600
•
Self
sets up self-signing certificates
•
CA
uses an authority to assign the SSL certificates
NOTE:
For more details on SSL settings, refer to the 3-Series®Control Systems Reference
Guide (Doc. 7150) at www.crestron.com/manuals.
To edit the CIP port, secure CIP port, CTP port, or secure CTP port, tap the corresponding
Edit
button and use the keyboard to enter the new information.
On the
Advanced Ethernet Setup
screen, tap
DNS Servers
to display the
DNS Servers
screen.
DNS Servers Screen
The
DNS Servers
screen provides controls for adding or deleting the IP addresses of DNS
(Domain Name System) registered computers on the network. To add a server’s IP address,
tap
New
to open an on-screen keyboard.
Use the keyboard to enter the IP address of the new DNS server. Tap
Clear
to remove a
previous entry,
Backspace
to delete the last digit,
Enter
to save a new entry, or
Cancel
to
return to the previous screen.
On the
Advanced Ethernet Setup
screen, tap the ellipsis (
…
) at the top to display the
On
and
Off
controls, which enable or disable the web server, and controls to edit the web port
and secure web port.
The default web server setting is
On
. Tapping
Off
disables access to setup from a web
browser.
To edit the web port or secure web port, tap the corresponding
Edit
button and use the
keyboard to enter the new information.
Supplemental Guide – DOC. 7593C FT-TSC600: FlipTop Touch Screen Control System •5

Advanced Ethernet Setup Screen (Web Server)
Edit the Ethernet Diagnostics
On the
Ethernet Setup
screen, tap
Ethernet Diagnostics
to display the
Ethernet
Diagnostics
screen.
Ethernet Diagnostics Screen
The
Ethernet Diagnostics
screen provides controls for verifying connections. Tap
Ping
Default Router
to verify connection to the router. (The screen displays a “Passed” message
to show successful connection.) Tap
Ping Crestron.com
to verify connection to an external
DNS server.
Tap
Who
to display a list of devices connected to the PC via the Ethernet connection.
These devices may be Crestron Ethernet devices, third-party Ethernet devices, or PCs
(including any PC using Crestron Toolbox™ to connect to the processor via Ethernet).
6•FT-TSC600: FlipTop Touch Screen Control System Supplemental Guide – DOC. 7593C