Crestron DM-RMC-4KZ-SCALER-C User manual

The Crestron® DM-RMC-4KZ-SCALER-C is a DigitalMedia 8G+® receiver
and room controller with scaler that supports full 4K60 4:4:4 and high
dynamic (HDR10) video signals. Via a CATx cable, the DM-RMC-4KZ-
SCALER-C connects to a DigitalMedia™ switcher or transmitter or to an
HDBaseT® source. Built-in RS-232, IR, and HDMI® CEC ports enable
programmable control of a display device via a control system.
In the Box
1 DM-RMC-4KZ-SCALER-C DigitalMedia 8G+ 4K60 4:4:4 HDR
Receiver and Room Controller with Scaler
Additional Items
2 Connector, 4-Pin (2003576)
2 Connector, 5-Pin (2003577)
Install the Device
The DM-RMC-4KZ-SCALER-C can be mounted onto a flat surface or
rack rail.
Mounting onto a Flat Surface
Using four mounting screws (not included), mount the device onto a flat
surface such as a wall.
Wall Mounting
1
DM-RMC-4KZ-SCALER-C QuickStart
DigitalMedia 8G+® 4K60 4:4:4 HDR Receiver and Room Controller with Scaler

Mounting onto a Rack Rail
The device can be mounted onto a front or rear rack rail. To mount
thedevice:
1. Position either of the mounting flanges so that the holes align with the
holes in the rack rail.
2. Secure the device to the rack rail using two rack mount screws
(notincluded).
Rack Rail Mounting Example
Connect the Device
Connect the device as required for the application.
NOTES:
lThe LAN port can be connected to an Ethernet switch only when
the DM IN port does not connect to a DigitalMedia switcher.
lThe DM IN port is a PoDM+ powered device (PD) port and is also
compatible with HDBaseT PoE+:
oIn order for the DM IN port to receive PoDM+, the port must be
connected to a DigitalMedia switcher or other DigitalMedia
equipment that has a PoDM+ power sourcing equipment (PSE)
port.
oIn order for the DM IN port to receive HDBaseT PoE+, the port
must be connected to equipment that has a corresponding
HDBaseT PoE+ PSE port.
Wiring that connects to a PoDM+ or HDBaseT PoE+ port is
designed for intrabuilding use only.
PoDM+, HDBaseT PoE+, or the optional PW-2412WU power pack
(sold separately) can be used to power the DM-RMC-4KZ-
SCALER-C.
lConnection of the CEN-SWPOE-16 to the POE IN ports of DMC-
4KZ-CO-HD output cards in a DigitalMedia switcher can provide
PoDM+ power to up to seven DM-RMC-4KZ-SCALER-C devices.
2
DM-RMC-4KZ-SCALER-C QuickStart
DigitalMedia 8G+® 4K60 4:4:4 HDR Receiver and Room Controller with Scaler

Connections, Left and Right Sides
3
DM-RMC-4KZ-SCALER-C QuickStart
DigitalMedia 8G+® 4K60 4:4:4 HDR Receiver and Room Controller with Scaler

The AUDIO OUT connector uses a 5-pin terminal block for balanced or
unbalanced analog audio output.
Refer to the following table and diagrams for analog audio output pin
assignments and connection information.
Signal Name Balanced Audio Output Unbalanced Audio Output
+ L+ L+ Out
− L− Open
G Shield/ground Common ground
+ R+ R+ Out
− R− Open
Upgrade the Firmware
Before using the device, upgrade the firmware. The latest firmware can be
downloaded from the DM-RMC-4KZ-SCALER-C product page on the
Crestron website (www.crestron.com).
Determine the IP Address
The physical configuration of the DM-RMC-4KZ-SCALER-C within a
DigitalMedia 8G+ system determines how the IP address of the receiver
isset:
lIf the DM-RMC-4KZ-SCALER-C is connected to a DigitalMedia
switcher, the IP address is configured by the switcher automatically.
You do not need to set the IP address.
lIf the DM-RMC-4KZ-SCALER-C is connected directly to a DigitalMedia
8G+ transmitter (commonly referred to as a standalone configuration
in which no DigitalMedia switcher is used), the IP address of the
receiver is assigned using DHCP (Dynamic Host Configuration
Protocol) by default. If you wish to assign a static IP address, do either
of the following:
oTo assign the default static IP address of the receiver, hold down
the SETUP button while the unit boots up. The default static IP
address, which is 192.168.1.253, overwrites the current setting.
oTo manually set a static IP address other than the default address,
use the Crestron Toolbox™ software.
4
DM-RMC-4KZ-SCALER-C QuickStart
DigitalMedia 8G+® 4K60 4:4:4 HDR Receiver and Room Controller with Scaler

Select the Input
The input source can be switched automatically (default setting) or
selected manually.
Automatic Switching
Automatic switching displays video from the last detected input source.
Manual Switching
To change from automatic switching to the desired video input source,
press the INPUT SELECT push button. Pressing the button in succession
changes the input source in the following order: DM IN,HDMI IN, and
Disable (no input is selected). After cycling through the available input
source options, pressing the INPUT SELECT button again returns to
automatic switching.
Observe the LED Indicators
Refer to the following table for information about the LED indicators on
the device.
LED
Indicator Color Meaning
SETUP Red The SETUP button is pressed.
Power Green Power is being applied to the device.
DM IN
signal
Solid
green
A video signal is detected at the DM IN port and DM IN
is the active input source.
Flashing
green
A video signal is detected at the DM IN port but DM IN
is not the active input source.
DM IN
port
Green A DM or HDBaseT link is established.
Solid
amber
HDCP video is detected at the input.
Flashing
amber
Non-HDCP video is detected at the input.
HDMI
IN
Solid
green
A video signal is detected at the HDMI IN port and
HDMI IN is the active input source.
Flashing
green
A video signal is detected at the HDMI IN port but
HDMI IN is not the active input source.
HDMI
OUT
Green A video signal is detected at the output.
LAN Green An Ethernet link is established.
Flashing
amber
Data activity is occurring on the Ethernet link.
5
DM-RMC-4KZ-SCALER-C QuickStart
DigitalMedia 8G+® 4K60 4:4:4 HDR Receiver and Room Controller with Scaler

Visit the Product Page
Scan the QR code to visit the product page.
DM-RMC-4KZ-SCALER-C
www.crestron.com/model/6508076
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Crestron Toolbox, DigitalMedia, DigitalMedia 8G+, and
DM are either trademarks or registered trademarks of Crestron Electronics, Inc. in the
United States and/or other countries. HDBaseT and the HDBaseT Alliance logo are
either trademarks or registered trademarks of the HDBaseT Alliance in the United
States and/or other countries. HDMI and the HDMI logo are either trademarks or
registered trademarks of HDMI Licensing LLC in the United States and/or other
countries. Other trademarks, registered trademarks, and trade names may be used in
this document to refer to either the entities claiming the marks and names or their
products. Crestron disclaims any proprietary interest in the marks and names of
others. Crestron is not responsible for errors in typography or photography.
©2020 Crestron Electronics, Inc.
Doc. 7937B
04/15/20
6
DM-RMC-4KZ-SCALER-C QuickStart
DigitalMedia 8G+® 4K60 4:4:4 HDR Receiver and Room Controller with Scaler