2
quickstart guide
CEN-NVS200
CEN-NVS200
Network Video Streamer
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
4Adding the CEN-NVS200 to Your Crestron System
QUICKSTART DOC. 7112A (2030044) 04.11
For details, refer to the latest version of the
CEN-NVS200 Operations & Installation Guide, Doc. 7111.
To add the CEN-NVS200 to your Crestron®system, perform the steps in Option 1 or Option 2:
● Option 1 uses Crestron VisionTools®(VT Pro-e®) programming and provides streaming video capabilities only.
● Option 2 uses both SIMPL™ Windows and VT Pro-e programming and provides streaming video, touchpanel control of PTZ cameras, control system response for digital I/O, motion detection and video detection.
Option 1: VT Pro-e Programming Only
1. In the ProjectView tab for the touchpanel, open the Embedded Applications
folder, then double-click MJPEG Viewer to open the “MJPEG Viewer
Embedded Application Properties” window.
2. Click the Camera Controls tab.
3. Enter the IP address, port number and HTTP command into the
appropriate fields, then click OK.
4. Save the project.
NOTE: For the HTTP command, enter the viewer name and viewer password
assigned when creating a viewer user account in section , step C4 on the
reverse side of this guide. For example, if the viewer name is MyViewer and the
password is viewmycamera, enter the following:
3
http://192.168.194.185/video3.mjpg?user=MyViewer&pw=viewmycamera
“MJPEG Viewer Embedded Applications Properties” Window
Option 2: SIMPL Windows and VT Pro-e Programming
SIMPL Windows Programming
1. Drag the CEN-NVS200 from the Ethernet Control Modules | Ethernet Video Modules folder
of the Device Libary and drop it in the System Views.
Device Library and Sample System Views
2. Double-click the CEN-NVS200 in the system tree to open the “Device Settings” window, then set the IP
address of the CEN-NVS200 (use the IP address set in section , step D2).
If desired, also change the IP ID of the CEN-NVS200.
3
CEN-NVS200 Module Parameters
3. In the Program View, select the
CEN-NVS200.
4. In the Detail View, enter data into
the following text boxes:
● Admin_Password
(Use the administrator
password entered in section
, step C2)
3
● Viewer_Name
(Use the user name entered
in section , step C4)
3
● Viewer_Password
(Use the password entered
in section , step C4)
3
5. Connect the CEN-NVS200 module outputs (Video_Server_Port_Number, NVS200_IP_Address,
NVS200_Stream2_HTTP_Command and all others required for your application) to the touchpanel definition.
Sample TPMC-8X Port Number Analog Join
Sample TPMC-8X IP Address and HTTP Command Serial Joins
VT Pro-e Programming
“MJPEG Viewer Embedded Application Properties” Window
1. In the ProjectView tab for the touchpanel,
open the Embedded Applications folder,
then double-click MJPEG Viewer to
open the “MJPEG Viewer Embedded
Application Properties” window.
2. Click the Camera Controls tab.
3. In the IP Address, Port # and HTTP
Command panes, set the join numbers
using the same numbers assigned (in
“SIMPL Windows Programming” step 5,
above) in the SIMPL Windows program,
then click OK.
4. Save the project.
NOTE: The URL will change depending on which video is desired. URLs can
be found on the “System” configuration page.
Crestron, the Crestron logo, Crestron Toolbox, SIMPL Windows, V-Panel, VisionTools and VT Pro-e are trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and other countries. Other trademarks, registered trademasks and trade names may be used in this document to
refer to either the entities claiming the marks and names or their products. Crestron disclaims proprietary interest in the marks and names of others.
©2011 Crestron Electronics, Inc.
● IP_ID
(Use the IP ID assigned to
the symbol)
