CrimeStopper CS-882 OEM User manual

CS-882 OEM
ALARM UPGRADE FOR FACTORY KEYLESS ENTRY
INSTALLATION & OPERATING INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS on your choice of an Alarm Upgrade System by Crimestopper Security Products Inc.
This booklet contains the information necessary for installing, using, and maintaining this system. If any
questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support
number below.
*IMPORTANT INFORMATION:
This system does not improve or affect the range of the factory remote keyless entry transmitters.
This is an ADD-ON system only. The arm/disarm range of this system will be identical to that of the
Factory Keyless System’s lock/unlock range.
TECH SUPPORT
Mon-Fri 8:00 AM-4:30 PM Pacific Time
[phone]
REV. A 8/2002 SW: PG30500030CT1
INSTALLATION PRECAUTIONS & WARNINGS
BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR
BAGS, ABS BRAKES, BATTERY, ETC.).
DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering
column, or any other moving parts in the vehicle.

COMPONENT MOUNTING
Control Unit: DO NOT mount or wiring harness where they can become entangled with moving parts such as
brake/gas/clutch pedals, or the steering column! The control module should be mounted in a concealed location. Do
not mount the control unit in the engine compartment.
LED: Mount in a visible location on the dashboard or console.
Valet/Program Button: Mount button in a hidden but accessible location. It is REQUIRED for emergency disarm,
programming, and valet mode.
WIRING
VIOLET WIRE #1 & #2: ON-BOARD RELAY (10A) IMMOBILIZER CIRCUIT #1 NORMALLY OPEN
These wires the are for an on board Relay to immobilize the Coil or Fuel Pump Circuit in the vehicle. Cut the selected
circuit you want to immobilize and connect each end to a VIOLET wire.
NOTE (1): This is a high-security, normally open connection. If the alarm system is unplugged or loses power,
the circuit will still be immobilized!
NOTE (2): This circuit has a maximum load of 10A and should NOT be used to interrupt a high current wire
such as an Ignition supply or Starter circuit from the ignition switch!
WHITE/RED: (-) NEGATIVE HORN/SIREN OUTPUT
Connect to wire that activates the factory horn. If you choose to use this output with a standard alarm (warble) siren,
then it should be connected to the black (negative) wire of the siren. Connect the red wire of the siren to constant (+)
12 Volts. NOTE: This wire is preset for a factory vehicle horn. You must change the programming for siren use. See
programmable option #15.
BLACK WIRE: SYSTEM CHASSIS GROUND
THIS WIRE MUST BE CONNECTED TO CHASSIS METAL OF THE VEHICLE. Scrape away any paint or dirt from
the area to ensure a good connection.
RED WIRE: +12V POWER INPUT (15 amp fuse)
Connect to +12 Volt source with supplied fuse & holder. Connect to the vehicle’s battery Positive terminal.
WHITE WIRE: +12V FLASHING PARKING LIGHT OUTPUT X2 (15 amp fuse)
Connect to switched parking light wire at back of light switch. If this is not possible, connect directly to one of the
parking lights at the front of the vehicle. Many European vehicles require separate right and left circuits. Use this
second white wire to connect to the 2nd light circuit on your European vehicle. Otherwise do not use both white wires.

WIRING
ORANGE WIRE: (-) NEGATIVE STARTER DISABLE (Armed output)
Ground output when system is armed. This output is used for disabling the starter or to activate other optional devices
such as scanner LED’s, window control modules, voice modules etc. For starter kill, cut starter wire and connect
between 87A and 30 on a relay. Connect orange wire to 85 and connect 86 to an Ignition source that has voltage in
“ON” and “CRANKING” positions at the Ignition switch. (Starter disable relay not included)
PINK/WHITE WIRE: ON-BOARD RELAY (10A) IMMOBILIZER CIRCUIT #2 NORMALLY OPEN
PINK WIRE: ON-BOARD RELAY (10A) IMMOBILIZER CIRCUIT #2NORMALLY OPEN
These wires the are for an on boardrelay to immobilize the Coil or Fuel Pump Circuit in the vehicle. Cut the selected
circuit you want to immobilize and connect one end to the Pink wire and the other end to the Pink/White wire.
NOTE (1): This is a high-security, normally open connection. If the alarm system is unplugged or loses power,
the circuit will still be immobilized!
NOTE (2): This circuit has a maximum load of 10A and should NOT be used to interrupt a high current wire
such as an Ignition supply or Starter circuit from the ignition switch!
YELLOW WIRE: +12 VOLTS IGNITION SWITCHED
Connect to an Ignition wire that shows +12 Volts with the key in both “On” and “Start” positions.
BLACK/WHITE WIRE: +12 VOLTS POWER TRUNK RELASE INHIBIT INPUT(If Equipped)
Connect this wire to the positive side of trunk release solenoid. This input wire will allow the CS-882OEM system to
sense when the Trunk Release Button is pressed on the Factory Remote Control. This will prevent an unwanted false
alarm if your vehicle has a powered trunk/hatch release. At the instant a positive pulse is sensed on this wire, the
trunk trigger, shock sensor, and current sensing features are bypassed. If the trunk is then re-closed (sensed by trunk
pin) the zone will re-arm in 3 seconds, otherwise system is STILL ARMED EVEN THOUGH THE TRUNK IS OPEN and
must be disarmed with the Unlock Button before entering vehicle.
BLUE WIRE: (-) or (+) DOOR TRIGGER (PROGRAMMABLE, DEFAULT IS NEGATIVE)
Connect to door pin activation circuit in vehicle:
•Negative type door circuits show Ground when any door is opened and 12 volts when all doors are closed. Some
vehicles may have isolated door triggers. In this case you may need to run additional wires from other doors or go
directly to the wire at the vehicle’s dome light.
•Positive type door circuits show 12 Volts when a door is opened such as on many Ford/Mercury vehicles.
*TIP: Many recent vehicles have door pin switches incorporated in the door latch itself, therefore there are not any
“plunger” type door switches located in the door jamb. If your vehicle has no door pins, an alternative connection may
be at courtesy light or locating the door triggers at a control module elsewhere in the vehicle. Call Tech Support for
assistance.

WIRING
GREEN WIRE: (-) HOOD/TRUNK TRIGGER
Connect this wire to a grounding hood / trunk pin switch or to existing factory hood and trunk pin switches that read
ground when open. If no existing switches are available, new pin switches may be installed. Note: DO NOT mount
new pin switches in water pathways.
RED/WHITE: (+/-) Door Unlock Validation Signal INPUT: [Default Setting is Negative]
Connect to Vehicle’s Door Unlock Switch wire. NOTE: The module must be programmed for the correct signal polarity.
(Flipping switch on top of control module will change the input polarity.) This wire prevents system from being defeated
simply by pressing the vehicle’s unlock button at the door panel when triggered.
GREEN/WHITE: (+/-) Door Lock Validation Signal INPUT: [Default setting is Negative]
Connect to Vehicle’s Door Lock Switch wire. NOTE: The module must be programmed for the correct signal polarity.
(Flipping switch on top of control module will change the input polarity.) Prevents system from being armed when
manually pressing the vehicle’s Lock button at the door panel.
BLUE/BLACK: Door Unlock Signal INPUT:
Connect to Vehicle’s (+12V) Door Unlock (Solenoid/Motor) Wire.
YELLOW/BLACK: Door Lock Signal INPUT:
Connect to Vehicle’s (+12V) Door Lock (Solenoid/Motor) Wire.
**SEE DOOR LOCK MOTOR / VALIDATION WIRE CONNECTIONS NEXT PAGE
WIRING: MINI PLUGS
2-PIN PLUG (WHITE): PROGRAM/VALET BUTTON Connects to white plug on module.
2-PIN PLUG (RED): LED INDICATOR (RED FLASHING LIGHT) Connects to red plug on module.
3 PIN SENSOR PLUG:
WHITE Wire: Negative Signal
BLACK Wire: Sensor Ground
RED Wire Sensor +12V Power
SHOCK SENSOR: The sensor supplied with
this system does not require any additional
wiring. Simply mount the sensor in a suitable
location, plug it in, and adjust the sensitivity.

4 ON
CURRENT SENSING
DIP SWITCH #4
OFF
CURRENT SENSING
The CS-882OEM system includes a current sensing circuit to monitor current
flow through the vehicles electrical system. If an intruder opens a door and the
interior lights turn on, the CS-882 system will detect a current drain and trigger
the alarm without having to connect (hardwire) this system to the interior dome
light circuit and hood/trunk pin switches. If your vehicle includes courtesy lights
in the trunk and/or under the hood, the system should also protect those areas
when in current sensing. Current sensor is off by default. See diagram at right.
CURRENT SENSING NOTES:
1. Current sensing may be a problem for you if your vehicle has a thermostatically controlled fan
system that may turn on after you have set the alarm and left the vehicle. The fan turning on will
cause a false alarm trigger.
2. Some vehicles with large or more then one battery will not operate well in current sensing mode
because there is not enough voltage drop for the unit to detect a light turning on. If you experience
problem with current sensing, please use the hard-wired door and hood/trunk inputs.
RESISTORS & DIODES
The enclosed diodes and resistors are only used for alternative installations that DO NOT +12V or Grounding
validations signals. (Door Lock/Unlock Switch wires).
Connect components as follows:
Yellow/Black: wire from CS882 connects to one side of resistor.
Remaining side of resistor connects to band end of diode.
Non-band end of diode (anode) connects to parking light switched +12 volt wire.
Blue/Black: wire from CS882 connects to one end of 2nd resistor.
Remaining side of resistor connects to band end of 2nd diode.
Non-band end of diode (anode) connects to door lock solenoid switch that switches from ground to +12 volts
when locking and unlocking.

2 31 4
ON
NEGATIVE VALIDATION INPUTS
(TOP EDGE OF 882 MODULE)
2 31 4
ON
POSITIVE VALIDATION INPUTS
(TOP EDGE OF 882 MODULE)
DOOR / LOCK & VALIDATION WIRES (TYPICAL INSTALLATION)
VALIDATION WIRES ON (MODE A = DIP SWITCHES 1-3 ON):
The Validation wires serve as a secondary input to prevent the
system from being armed or disarmed simply by pushing the unlock
button on the vehicle.
ARM/DISARM VALIDATION WIRES:
ARMING: The CS-882OEM system will NOT ARM if a NEGATIVE
(or POSITIVE*) pulse is sensed on the GREEN/WHITE wire. (The
Lock button on the door panel vehicle was pressed)
DISARMING: The CS-882OEM system will NOT DISARM if a
NEGATIVE (or POSITIVE*) pulse is sensed on the RED/WHITE
wire. (The Unlock button on the door panel was pressed).
*See Positive/Negative Signal setting diagrams at right and below.
L
U
FACTORY
POWER
LOCK
RELAYS
LOCK
SWITCH
(+) LOCK / MOTOR WIRE
(+) UNLOCK / MOTOR WIRE
YELLOW / BLACK BLUE / BLACK
GREEN / WHITE
RED / WHITE
+ / - LOCK SWITCH WIRE *
+ / - UNLOCK SWITCH WIRE *
(*Programmable for POS/NEG validation)

PROGRAMMABLE OPTIONS
1. Turn the Ignition ON and press the Override/Program button 7 times within 10 seconds.
2. Turn OFF Ignition. LED will flash slowly once per second as and indicator the system is in programming
mode.
3. Within 20 seconds, press the Override/Program button the number of times that corresponds to the feature
list below. The siren will chirp for each button press. DO NOT LOSE COUNT!! If you can hold down the
button for 3 seconds and release you get 2 chirps. A 3-second button press is the same as pressing the
button 10 times.
4. When you get to the desired option number, turn the Ignition from OFF to ON to toggle between the preset
and alternate settings. The siren will chirp once or twice indication which value the feature is at. See Below
for Option numbers, descriptions, and values. Ignition should be left in the OFF position once your have
the correct value.
5. At this time, if you need to change more options, repeat steps 3 & 4 above.
6. To exit programming Mode, Turn Ignition ON and press the Override/Program button once.
OPTIONS CHART
Option #
Option Description PRE-SET Value
(1 chirp) ALTERNATE Value
(2 chirps)
1Flashing Lights ON OFF
6Siren Chirps ON OFF
8Passive Arming OFF ON
10 Door Trigger Input Polarity
(Blue wire) NEGATIVE POSITIVE
14 Allow Panic Mode OFF ON
15 Horn or Siren output
(White/Red wire) HORN SIREN
25 Restore all options to PRE
SET VALUES YES

OPERATION
ARMING
To arm the alarm and lock the doors, press the Lock button of your Factory Keyless Remote Control. The 882
OEM system will sense the Door Lock signal and Arm. The lights will flash once, the vehicle horn or siren will
chirp once. After 3 seconds, the LED indicator will begin flashing slowly and Immobilizer circuits become
active. This system is now armed and ready to protect the vehicle.
ALARM TRIGGERING:
If there is an intrusion into the vehicle or hard impact to the body the alarm will sound which consists of
flashing lights and siren or pulsing car horn for 30 seconds. After the 30 second alarm cycle duration the
system will stop, but is still armed. LED will begin flashing rapidly indicating the alarm has been triggered.
DISARMING:
To disarm the CS-882 OEM, press the Unlock button of your Factory Keyless Remote. The CS-882 OEM
system will sense the Door Unlock signal and Disarm. The lights will flash twice and the vehicle horn or siren
will chirp twice. The LED will stop flashing. If the system was tripped in your absence, then the siren or horn
will chirp 4 times and the lights will flash 4 times. If your hear 4 chirps/flashes, we recommend inspecting your
vehicle for a theft attempt or damage.
PASSIVE ARMING MODE (Programmable Option)
When programmed for Passive (Automatic Last Door Arming) the CS-882 will arm itself 30 Seconds after the
ignition is turned off and the last door has been closed. If a door is reopened, the system will wait for the door
to close before arming.
DUAL-STAGE SHOCK PROTECTION
If a low-level shock to the vehicle body is detected, the pre-warning sensor activates sounding 1 siren/horn
chirp and one light flash. If a hard impact to the vehicle occurs, the system will trigger for 30 seconds. Adjust
the shock sensor as needed by turning the control knob clockwise to increase sensitivity and counter-
clockwise to decrease sensitivity.
EMERGENCY OVERRIDE/DISARM
If the CS-882 system is armed and you have lost your Factory Keyless Remote or it stops working, you will
have to perform an emergency override. Enter your vehicle manually with the key, (this will trip the alarm) turn
the Ignition ON, and press override/program button 5 times within 8 seconds to disarm the system. The
system will chirp/flash 4 times when disarmed.

OPERATION
VALET MODE
To disable alarm functions of the 882 system, turn the Ignition ON and press the override/program button 3
times within 8 seconds. After 8 seconds, the dash LED turns on solid as an indicator that the system is in valet
mode. Repeat this steps to exit VALET mode. The LED will go out, system will chirp (2) times and the light
will flash (2) times when exiting valet mode.
When in VALET mode the siren will still chirp for lock/unlock confirmation even though alarm functions are
disabled. The CS-882 system will chirp 2 times when locking the doors and 3 times when unlocking the
doors.
PANIC MODE (Programmable Option)
To activate your system during an emergency situation or to attract attention to your vehicle, press the Lock
button on your remote 3 times within 5 seconds. This will activate a 30-second alarm trigger. Press any
button on your remote to disarm.
FACTORY TRUNK RELEASE SENSING
If the CS-882 system is installed in a vehicle with trunk pop or hatch release button on the Factory Remote,
there is a special input wire that will prevent the system from triggering if the trunk button on your remote is
pressed while the system is armed.

WIRING DIAGRAM
VALET/
IGN SW.
STARTER
STATUS LED
FUSE
BOX
IGNITION ON &
CRANKING VOLTAGE
STARTER WIRE
85
87A
CUT
86
30
RED
VIOLET
BLACK
WHITE/RED
(-) ARMED OUTPUT
(STARTER DISABLE)
IGN
SW.
ORANGE
WHITE
FUSE
15A
PARKING LIGHTS
SHOCK SENSOR
BATTERY
CS-882
OEM
PROGRAM
BUTTON
+
IMMOBILIZE
(Low-Current circuit)
VIOLET
+12V
SIREN
OR
HORN
CHASSIS
GROUND
WHITE
PARKING LIGHTS
FUSE
15A
FUSE
15A
USE ONLY FOR
EUROPEAN VEHICLES
WITH 2 PARKING LIGHT
CIRCUITS.
PINK/WHITE
PINK
LED: RED PLUG
VALET: WHITE PLUG
CONNECTS TO POSITIVE
SIDE OF TRUNK RELEASE
OF TRUNK SOLENOID
OR
NEG. or POS
DOOR PIN SW.
(Programmable)
NEGATIVE
PIN SW.
YELLOW/BLACK BLUE/BLACK
NEG. SIREN or HORN OUTPUT
CHASSIS GROUND
CUT
COIL or FUEL PUMP
+12V POWER INPUT
+12V PARKING LIGHT OUTPUT
+12V PARKING LIGHT OUTPUT #2
ON-BOARD IMMOBILIZER
ON-BOARD IMMOBILIZER #2
IMMOBILIZE
(Low-Current circuit) CUT
COIL or FUEL PUMP
YELLOW
+12V IGN. INPUT
BLACK/WHITE
BLUE
GREEN
(-)NEG. HOOD/TRUNK INPUT
UL
L
RED/WHITE
GREEN/WHITE
*POS or (-)NEG. LOCK SW. INPUT
*POS or (-)NEG. UNLOCK SW. INPUT
POSITVE UNLOCK MOTOR INPUT
POSITVE LOCK MOTOR INPUT
(*Programmable)
SEE PAGE #5 OF MANUAL