CrimeStopper The Informer II CS-2016FM User manual

CS-2016FM The Informer II™
2-Way FM Paging Alarm & Remote Engine Starting System
OPERATION INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS on your choice of the Informer II™ by Crimestopper Security Products Inc. This booklet
contains the information necessary for operating your system. If any questions arise, contact your installation dealer or
Crimestopper Security Products Inc.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Power,
Ground, LED, etc.
-OPTIONAL: Optional features are connected only if desired or agreed upon by the installing dealer i.e. Horn Honk,
Dome light illumination, Door Locks, Trunk Pop, etc. These features may require additional parts and labor charges.
Consult with your installer about these features BEFORE installation!
CONTACT INFORMATION: This device complies with FCC Rules part 15. Operation is subject
to the following two conditions: 1) This device may not cause
interference, and (2) this device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modification to this
equipment. Such modification could void the user's authority to
operate the equipment.
TECHNICAL SUPPORT (800)-998-6880
Monday - Friday 8:00am - 4:30pm Pacific
Website: www.crimestopper.com
E-mail: [email protected]
CRIMESTOPPER
SECURITY PRODUCTS, INC.
1770 S. TAPO STREET
SIMI VALLEY, CA. 93063 REV. B 09.2004

TABLE OF CONTENTS
Operation Cautions & Warnings……..…………..……………………………………………………………………2
Transceiver / Pager-Remote……….....…………..……………………………………………………………………3
CS-397TW Sidekick Remote Control…………………….…………………………………………………..…...…..4
Operating Instructions - Alarm……………………………………………………….………..……………..……..4-8
Remote Engine Control………………………...……………………………………………….…….………...….9-13
Anti-Carjack Protection...……………………………………….………….……..………………..………..………..14
LED Diagnostics………………..……………………………………………………………………….………..….…15
Transceiver / Remote Control Programming……………………………………………………..……………15-16
2 Vehicle Operation……...………………………….……………………………….………….…………….….……17
Troubleshooting / FAQ Section……………….…………………………………………………………..……..18-19
Low Battery Warning – LCD Remote / Setting Clock – LCD Remote……………………………….….…19-20
OPERATION CAUTIONS & WARNINGS
CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident
resulting from the use of this equipment. This system is designed to be professionally installed into a car or
vehicle in good running order. Items, such as parking brake, door switches, and all engine safety features,
must be in perfect working condition.
DAMAGE resulting from misuse or negligence is NOT covered under warranty and will be subject to
repair and / or replacement charges.
IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this
system and its safety features. B) Check for proper operation of these safety features prior to accepting
delivery of the vehicle from the installation facility. C) Check and maintain the condition of the vehicle and all
items relative to the proper operation of this system and its safety features.
DO NOT remote start the vehicle in a closed garage. Make sure that the vehicle is outdoors, a garage door
is open, or there is adequate exhaust ventilation. Failure to observe this rule could result in injury or death
from poisonous Carbon Monoxide fumes. This is especially important when using the Timed Self-Start feature
of the unit 2

TRANSCEIVER / PAGER-REMOTE
PAGER / REMOTE TRANSCEIVER:
#1 ARM/
LOCK
#4 ENGINE
START/STOP
#5
RECALL /
CAR I OR II
#3 TRUNK
POP
#2 DISARM/
UNLOCK
ANTENNA
START
FIXED
LCD
SCREEN
PM
The hand-held remote transceiver is used to send and receive
information from the vehicle. The Control Module transmits High
Frequency FM signals from the vehicle to your over long
distances. Your range will vary depending on location, terrain,
and local RF noise/interference. This system is not guaranteed
to page you if you are behind concrete walls, underground, in a
large structure, or in an area with high levels of electronic
interference. Handle the pager/remote with care if the LCD
display and/or the electronics may be damaged if subjected to
abuse. The AAA Cell 1.5V alkaline battery can easily be
replaced by sliding open the battery access door on the back of
the remote. Battery life will vary depending on usage. The LCD
screen will display a low battery icon when the battery is low.
For more on range, see “Range Questions” on page 15.
ACTIVE 2-ZONE LCD DISPLAY:
The unique LCD screen includes both a Dot Matrix animated display and a vehicle icon. It is designed to show you
both Icon-based information and animated messages in real time as it is happening. When the alarm is disarmed or
armed with no activity to report, then dot matrix portion of the screen will remain BLANK.
BUTTON 1(Lock Symbol): BUTTON 5 (On side of remote):
•Press and Release to Recall the
last message from the LCD screen
•Press and Hold for 3 seconds to
change from Car 1 to Car 2 (Only
for use with 2-car operation).
•Press 5 times to Disable/Enable
audible beep tones from the
remote. (Remote will vibrate twice
to confirm silent mode)
•Press and release to Arm/Lock system.
•Press and Hold for more than 3 seconds to activate “Panic” feature.
BUTTON 2 (Unlock Symbol):
•Press and release to Disarm/Unlock system, or reset a cycle.
BUTTON 3 (Trunk Symbol):
•Press and Release to activate trunk pop (Auxiliary output #1) Optional
Feature.
•Press and Hold to activate a second optional feature (Auxiliary output
#2).
BUTTON 4 (Key):
•Press and release to Start/Stop engine. 3

CS-397TW SIDEKICK REMOTE
The CS-397TW 1-Way sidekick remote
adds flexibility to your CS-2016FM. You
can have the convenience of operating your
system without needing to carry the larger
pager remote. The Sidekick remote has
less range and offers all of the same
operation features except for page-back
confirmation. See diagram below for
Sidekick 1-Way remote operation.
CrimeStopper
#3
#1
#2
#4
LOCK/
TRUNK
REMOTE
UNLOCK/
VEHICLE 2
FLASHLIGHT
START
#5
#6
ARM
DISARM
BUTTON 1(Lock Symbol):
•Press and release to Arm/Lock system.
•Press and Hold for more than 3 seconds
to activate “Panic” feature.
BUTTON 2 (Unlock Symbol):
•Press and release to Disarm/Unlock system, or reset a cycle.
BUTTON 3 (Trunk Symbol):
•Press and Release to activate trunk pop (Auxiliary output #1) Optional Feature.
•Press and Hold to activate a second optional feature (Auxiliary output #2).
BUTTON 4 (Key):
•Press and release to Start/Stop engine.
BUTTON 5 (Upper side button of remote):
•Press for convenient flashlight function. The high-power LED acts as a mini flashlight.
BUTTON 6 (Lower side button of remote):
•Press and release to activate Vehicle #2 mode. (Led witl flash for 4 second to use vehicle #2, otherwise
remote will revert back to Vehicle #2 4

OPERATING INSTRUCTIONS - ALARM
Active Arming / Locking:
PM
ARM/LOCK
Press button #1 (Lock symbol) on the transceiver. The System will arm emit one siren
chirp, one light flash, and the LED will begin to flash. Power locks will lock (if
equipped). Starter disable circuit will turn on. LCD Pager will beep once while
displaying a Down Arrow and a Lock symbol followed by the CSP logo. After a short
delay to allow the vehicle and electronics to settle, the system will be completely armed.
Disarming: / Unlocking
PM
DISARM/UNLOCK
Press button #2 (Unlock symbol) on the transceiver. System will disarm and confirm
with two siren chirps, two light flashes, and the LED will turn off. Power locks will Unlock
and Interior Dome light will turn on (if installed with these optional features). LCD Pager
will beep twice while displaying an Up Arrow and an Unlock symbol followed by the CSP
logo.
Alarm Triggers:
If there is an intrusion into the vehicle, a hard impact to the body, or the ignition is turned on the alarm will
sound and flash the lights for 1 minute. After 1 minute, the trigger cycle will automatically stop and alarm will
remain armed to continue protecting the vehicle. If a door is left open after an intrusion then the unit will cycle
a maximum of 5 minutes and continue to protect the other un-tampered or unopened zones.
LCD Remote Paging / Zone Violations:
When the system is triggered, the alarm sends a paging signal to the remote. If you are within range, you will
receive a violation paging signal which consists of a vibration followed by 15 audible beeps to notify you the
vehicle has been tampered with.
PM
DOOR TRIGGER
PM
HOOD/TRUNK TRIGGER
PM
SHOCK TRIGGER
PM
IGN
(<<<< MOVING <<<<<)
IGNITION TRIGGER
5

OPERATING INSTRUCTIONS - ALARM
Disarming While Tripped (Triggered):
Disarming the System while it is triggering requires TWO presses of the #2 Unlock Button. The first press of
Button #2 Resets the alarm cycle only (system still armed) while a second press will disarm/unlock the system.
Selective Silent Arming/Disarming:
To Arm or Disarm the system without siren
chirps, press and release both Buttons #2
(Unlock) and #4 (Start) at the same time.
System will Arm or Disarm without siren chirps.
Flashing lights and LED will be the only
indicators of Arm/Disarm status. The LCD will
Display a musical note with an “X” when the
system is armed or disarmed without a chirp.
PM
SILENT ARM
PM
SILENT DISARM
Prior intrusion Alert
This system will notify you if the alarm was tripped while you where away. Upon disarming, the two normal
disarm chirps will be heard then the system will emit 4 additional siren chirps. Check your vehicle for any
signs of a break in or tampering. Also see LED Diagnostics Section to determine the cause of the trigger.
Remote Panic Protection
To sound the alarm in an emergency situation or to draw attention to your vehicle, press
and hold Button #1 (Lock) for at least 3 seconds until the siren sounds. Press Button #2
(Unlock) to reset panic mode. The LCD pager/remote will display a “P” and emit 15
beeps when the panic mode is triggered.
PM
P
PANIC MODE
Selective Shock Sensor Disable
To arm the alarm and bypass shock sensor protection, press Button #1 as normal then
press and release Button #1 and #2 together within 2 seconds. You will hear 3 extra
siren chirps indicating shock sensor bypass for this arming cycle only. This feature can be used when parking
near railroad tracks, airports, or area with excessive loud machinery or noise to prevent the nuisance of
unnecessary false alarms.
Open Door Alert / Bypass
Upon arming, this system will warn you if a door is left open. The LCD pager will vibrate and beep (15X’s)
along with displaying the open zone on your LCD screen. This zone will automatically be bypassed until
closed, otherwise the alarm will continue to protect all other zones.
6

OPERATING INSTRUCTIONS - ALARM
Pre-Warning Shock Protection
PM
PRE-WARN
The Pre-warning (warn-away) feature will activate when a low-level shock or vibration
detected by the system’s shock sensor. The alarm will chirp the siren 5 times and
flash the lights once to help deter any further tampering with the vehicle. The
pager/remote will vibrate twice and beep (15X’s).
Passive Arming Mode: (Programmable)
Passive (automatic) arming occurs 30 seconds after the ignition is turned off and the
last door is closed. Upon closing the last door, the unit will flash the lights twice and LED will be flashing
rapidly to confirm passive countdown. If a door is reopened within the 30 second period, the countdown stop
and begin again when the door is closed. Passive arming provides failsafe protection in case you forget to
arm the system.
Passive Locking: (Programmable)
PM
PASSIVE LOCK/ARM
The CS2016FM system can be programmed to passively lock the doors when the
system passively arms. The default setting is OFF because passive locking
increases the risk of locking the keys in the vehicle. When the system arms/locks
passively, without you pressing the remote, the LCD pager will still provide a
confirmation signal. The LCD screen will have an arrow only without a lock symbol.
Trunk/Hatch Pop (Optional, Remote AUX. Output 1)
This feature is designed to interface with existing Factory power trunk or power
hatch release systems and may require additional parts and/or labor charges.
Press and release Button #3 (Trunk) on the transmitter to pop/open the trunk/hatch.
If the system is armed, it will also disarm when the button #3 is pressed. The LCD
pager/remote will confirm with 3 beeps and the trunk icon on the screen.
PM
TRUNK POP
Remote AUX. Output 2 (Optional, Requires special programming)
This system contains a second auxiliary output to activate other accessories or devices. To activate the
systems’ Second Auxiliary Output, press and HOLD Button #3 (Trunk Symbol) on the transmitter for more than
2 seconds. This is a momentary output that will stay active as long as the remote button is held down. There
is no LCD/pager confirmation for Aux. 2 output.
Dome Light Illumination (Optional)
This feature will turn on the vehicle’s dome light upon disarming for 30 seconds or until the key is inserted and
turned on. This will provide illuminated entry to your vehicle in dimly lit areas for safety and security. 7

OPERATING INSTRUCTIONS - ALARM
Emergency Override (Disarm)
If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to
disarm the system manually. Open the door with the key [alarm will sound], turn the ignition on, and press the
override/program button for about 5 seconds. The Alarm will disarm and allow you to use the vehicle until you
can repair/replace the remote. Valet mode also prevents Passive Arming.
Valet Mode (Enter manually or using the remote)
To disable Alarm and Remote Engine Starting for vehicle servicing or otherwise, turn the ignition on and press
the override/program button [about 5-7 seconds] until you hear (3) siren chirps and the LED turns on solid.
Repeat the process to exit VALET mode. To enter / exit valet via the remote, press and hold both buttons #1
(Lock) and Button #2 (unlock) together for about 3 seconds until 3 chirps are heard. Repeat this step to exit
via the remote transmitter. Lock/Unlock and AUX features will still operate in when in VALET mode however
remote start and alarm functions are inhibited.
Valet Park Mode (Using the remote transmitter only)
Note: Valet Park mode is only accessible when using the remote transmitter. Valet park mode allows you to
turn over the vehicle to a valet allowing access to drive/lock/unlock your vehicle, but alarm will trigger if the
trunk is opened. To activate Valet Park, press and hold both buttons #1 (Lock) and Button #2 (unlock)
together for about 6 seconds. 3 chirps will be heard first when unit goes into regular Valet and as you
continue to hold both buttons you will hear 2 more chirps. LED will always flash slowly when in Valet Park
even when the Ignition is turned on (or driving vehicle). Repeat step above to exit Valet Park mode.
PM
V
ALET UNLOCK
PM
V
ALET LOCK
PM
VALET MODE
Optional M.A.P. (Mobile Accessories Protection)
This system can be programmed to provide Crimestopper’s unique M.A.P. (Mobile Accessories Protection) feature that
allows you to prevent unauthorized access of your vehicles Audio, Cellular, Navigation, or Entertainment systems.
This feature is OPTIONAL and requires extra parts and labor for installation. Consult your installation dealer about
MAP before or during installation. The CS2016FM must be programmed for MAP operation. When the system is put
into Valet Park mode, M.A.P. will prevent stereo, entertainment, navigation, or cellular system from being used.
8

REMOTE ENGINE CONTROL
REMOTE ENGINE STARTING - SUCCESSFUL START
1) Press remote start button on the remote transmitter. System will chirp 3 times for audible confirmation.
(Chirps can be programmed on or off-See installation manual.)
2) Parking lights flash once, then turn on solid, Ignition/Accessory circuits turn on.
3) After a few seconds, Starter Motor engages, Parking lights and Accessory circuits turn off while cranking.
4) Engine Starts and Runs. Parking Lights and Accessory turn back on, Doors Lock.
5) Engine will remain running for programmed run time until reset with Brake pedal. If needed, the engine can
be turned off with remote transmitter.
REMOTE ENGINE STARTING - SUCCESSFUL START DIAGRAM:
AFTER
IGN
3
STARTER
THEN
FLASH 1X
SOLID
SOLID
SEC.
START
PM
IGN
CONFIRM REMOTE
START REQUEST
REMOTE ENGINE STARTING – LCD PAGER-REMOTE:
PM
IGN
(<<<< MOVING <<<<<)
SUCCESFUL START
When requesting a remote start the LCD pager remote
will confirm with an Ignition Icon along with 4 beeps.
Once the vehicle has successfully started the remote will
confirm back with 2 vibrations, a moving vehicle Icon, and
4 beeps.
9

REMOTE ENGINE CONTROL
UNSUCCESSFUL REMOTE START
In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then
attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank
time of up to13 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to
13 seconds to help prevent damage to the starter from over cranking.
1) If engine starts on 2nd or 3rd attempt, see steps 4 & 5 (on last page) under "Successful Start".
2) If Third attempt fails to start engine, the system will turn off and doors will remain locked. NO FURTHER
ATTEMPTS WILL BE MADE AUTOMATICALLY UNLESS YOU PRESS THE REMOTE START BUTTON
AGAIN.
TURNING OFF YOUR REMOTE STARTED ENGINE (VIA REMOTE CONTROL):
1) Engine is running in Remote Start (Parking lights ON).
2) Press Remote Start button on remote transmitter.
3) Engine & parking lights turn OFF, Doors remain locked or will re-lock if applicable.
ENGINE & LIGHTS OFF
START
ENTERING YOUR REMOTE STARTED VEHICLE:
1) With engine running, Remote Unlock/Disarm system (If armed) or open door with key.
2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset)
3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park.
4) Remote starter will reset instantly when the brake is pressed. Parking lights will turn off and the ignition key
is now controlling your vehicle. 10