Criterion MENTOR1600R Installation guide

- Due to the weight and size of this desk it is recommended that
assembly and installation be completed by two people.
- When possible assemble the unit where it is to be used
to limit the need to move it again.
- Please follow these assembly instructions as it will save you time,
make assembly easier and prevent possible damage to your unit.
- Correct Assembly is your responsibility.
- We strongly recommend that the unit is assembled on a soft
surface such as a carpet or blanket.
- We suggest the use of hand tools only to tighten the screws
and fittings, as power tools can strip threads if over tightened.
- When moving this furniture item, always carry the unit. Dragging
or sliding the unit could damage the unit and the floor surface.
MENTOR1600R
1600
1600
1400
750
400
067
635

x 74 x 74 x 18
x 1x 1
x 2
IMPORTANT: MISSING / DAMAGED PARTS WILL NOT BE REPLACED UNLESS THE INFORMATION
REQUIRED IS SUPPLIED IN FULL
EXPLODED VIEW
TOOL REQUIRED
HARDWARE KIT
Due to the weight and size of this desk, and the associated components, it is recommended that assembly
and installation be completed by two people.
x 74
CAM STICKERS
x 24
1
2x 8
x 4

STEP1
STEP2
STEP3
x 18
x 6
x 12
arrowhead on cam points
toward to the hole on the
panel edge.
! It is Recommended that Assembly and Installation be Completed by Two People !

x 4
STEP6
x 4
STEP4
STEP5
arrowhead on cam points
toward to the hole on the
panel edge.
! It is Recommended that Assembly and Installation be Completed by Two People !

STEP8
STEP7
x 4
x 8
arrowhead on cam points
toward to the hole on the
panel edge.
! It is Recommended that Assembly and Installation be Completed by Two People !
x 4
x 8

STEP9
STEP10
x 6
arrowhead on cam points
toward to the hole on the
panel edge.
! It is Recommended that Assembly and Installation be Completed by Two People !
x 6

STEP11
x 6
arrowhead on cam points
toward to the hole on the
panel edge.
! It is Recommended that Assembly and Installation be Completed by Two People !
STEP12
x 6

STEP13
STEP14
x 10
arrowhead on cam points
toward to the hole on the
panel edge.
! It is Recommended that Assembly and Installation be Completed by Two People !
x 10

STEP15
STEP16
arrowhead on cam points
toward to the hole on the
panel edge.
! It is Recommended that Assembly and Installation be Completed by Two People !
Roll Unit Over

x 10

STEP17
STEP18
arrowhead on cam points
toward to the hole on the
panel edge.
! It is Recommended that Assembly and Installation be Completed by Two People !
x 10
Roll Unit Over

STEP19
STEP20
arrowhead on cam points
toward to the hole on the
panel edge.
! It is Recommended that Assembly and Installation be Completed by Two People !
x 8
x 8
x 1
x 1
Drawers
Insert Drawers into
Return. Fit Cable
management
components.
2x 8
2
2
2
2
x 2
11
!Use E1 Screw to secure drawer base to bottom of Part 16!
(Take care not to split wood)

STEP21
STEP22
x 2
x 2
x 8
x 6
x 2
arrowhead on cam points
toward to the hole on the
panel edge.
! It is Recommended that Assembly and Installation be Completed by Two People !
! Before moving to the next step please position Return where it will be used in the office !
x 2
1
1
1

STEP24
STEP23
Secure modesty panel to Leg
with six screws, part E1
arrowhead on cam points
toward to the hole on the
panel edge.
! It is Recommended that Assembly and Installation be Completed by Two People !
! Before moving to the next step remember to position Return where it will be used in the office !
! Due to the weight of the Leg Please Don’t move Desk with Leg and Modesty Panel attached !
x 2
1x 6
x 2

arrowhead on cam points
toward to the hole on the
panel edge.
STEP25
STEP26
x 6
! It is Recommended that Assembly and Installation be Completed by Two People !

STEP27
Secure desk top to Leg
with twelve screws, part E1
and two part H
x 12
1
x 2
x 74
CAM STICKERS
Cover CAM Locks with Stickers
Supplied

SURFACE CARE INSTRUCTIONS
A lile care and aenon will extend the life and good looks of your furniture. Take care
when using materials which might spill, or be sharp or abrasive, on the surface of your
furniture.
Normal Cleaning For normal cleaning use a so, dry, clean cloth.
Glass Cleaning for Frosted Glass Do not use glass cleaner or solvent based cleaners on the
surface of the glass that has the frosng eect on it.
Normal Glass Cleaning You may use normal glass cleaning productson all other types of
glass. Use a so non -abrasive cloth to remove light dust and nger prints.
Vinyl and Cloth Cleaning Under no circumstances should any abrasive materials be used on this
surface, as it will result in unrepairable damage.
Do not use solvents, solvent based cleaners, scouring pads, steel wool, furniture wax or
scrubbing brushes.
Only use a slightly damp, so, clean cloth on this surface if cleaning is needed. Do not scrub.
CAUTION
As wit h all furniture, this unit should not be exposed to direct sunlight, extreme
temperatures or moisture, as this can result in non-repairable damage.
Note: The sooner a spill or mark is cleaned, the easier it will be removed.
Customer Service
FOR ALL MISSING OR FAULTY PARTS:
PLEASE RE-CHECK YOUR PACKAGING TO ENSURE THAT PARTS ARE MISSING THEN CONTACT THE
STORE YOU PURCHASED THE ITEM FROM.
THE STORE WILL NEED THE FOLLOWING INFORMATION…..
-COPY OF YOUR PURCHES SLIP/RECEIPT
-MODEL NUMBER OF THE UNIT PURCHASED
-DESCRIPTION/PART NUMBER OF THE MISSING OR FAULTY PART
-QUANTITY OF THE PARTS NEEDED
If for whatever reason you cannot get in contact with the store, please get in contact with Criterion direct at
hp://www.rvm.com.au/contact/
Product of RVM Australia
11 Tamara Drive, COCKBURN CENTRAL
Perth, Western Australia 6164
PH: 08 9417 9944

WARRANTY POLICY
1. Nothing in this Warranty affects the Consumer’s rights under the Australian Consumer law. The
benefits to the Consumer under this Warranty are in addition to the rights and remedies of the
buyer under any Consumer Guarantees. The Australian Consumer Law requires that we confirm that:
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality.
2. Subject to Clause 1, the Seller warrants that CRITERION branded products will be free of
manufacturing defects and will perform to the Seller’s specifications subject to the following clauses.
3. The benefit of this 12 Month Warranty extends only to the owner of the property in which the
Products manufactured or supplied by the Seller are installed and used by the owner for the
duration of the Warranty Period.
4. If within the Warranty Period a manufacturing defect is discovered in the Product, or the Product
fails to perform to the Seller’s specifications as a result of some defect in material or workmanship,
then the Seller will replace or repair the goods under Warranty or refund the purchase price paid by
the consumer (except if the failure is a major failure)
5. The Warranty does not apply to Product that:
a.) Has failed due to excessive wear and tear beyond what is considered to be reasonable.
b.) Has been misused or neglected.
c.) Has been damaged accidently or by acts of God including fire and flooding.
d.) Has been used or operated contrary to operating or maintenance instructions.
e.) Has been damaged in transit from the Sellers store to the buyer, either by the buyer or a third
party authorised to act for the buyer.
f.) Was incorrectly assembled or installed
6. In order to make a claim under the Warranty, the Owner must provide proof of purchase in all
cases.
7. The seller will examine any returned Products and if the Seller determines that there is an
apparent defect through no fault of the Owner, the Seller will:
a.) Make note of the Owner’s contact details including the Owner’s telephone number which the
owner can be contacted during business hours, postal address and e-mail address.
b.) Make note of the defects reported by the Owner.
c.) Take back the defective goods from the owner and determine within a reasonable time through
dialogue with the Seller whether the goods are defective.