Classic Exhibits visionary designs VK-2084 User manual

www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2084 - General Layout
Plan View
10’
20’

www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2084 - Backwall Assembly
When assembled
Velcro indicated in BLUE
BACK VIEW
Item
1
2
3
4
5
6
7/7a
8/8a
9/9a/9b
10/10a/10b
Qty.
5
1
1
1
1
1
1/1
1/1
1/1/1
1/1/1
Description
Oval Baseplate
80” Vertical Extrusion
80” Vertical Extrusion
80” Vertical Extrusion
80” Vertical Extrusion
80” Vertical Extrusion
46” Horizontal Extrusion
46” Horizontal Extrusion
46” Horizontal Extrusion
46” Horizontal Extrusion
Steps:
1) Attach Oval Baseplates to Vertical Extrusions
[2, 3, 4, 5, 6]
2) Connect Horizontal Extrusions
[7, 7a, 8, 8a, 9, 9a, 9b, 10, 10a, 10b] between Vertical
Extrusions [2, 3, 4, 5, 6] as shown.
3) Connect Wings to Vertical Extrusions [2, 6] as
shown (see Clamp Attachment Detail).
4) Attach lights to Horizontal Extrusions
where desired.
When desired location
is found, tighten
set screw to secure.
Slide connector on back
of A10 clamp into groove
of extrusion.
Example of Clamp Attachment
Tighten knob to secure
shelf/wing in place.
*
*Light Connection
Attach lights to
backwall where
desired and
tighten in place.
2
6
7
8
9
10
7a
9a
8a
10a
9b
10b
3
4
5
1
111
1
Wing
Wing
Wing
Wing
****
*
*
*
*
*
*
*
*

www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2084 - Header Assembly
Header Attachment
11
14
14a 15a
15
12
13
When assembled
Infill Infill
Item
11
12
13
14/14a
15/15a
Qty.
1
1
1
1/1
1/1
Description
16.4” Horizontal Extrusion
19.4” Horizontal Extrusion
24.5” Horizontal Extrusion
50.0” Extrusion
76.75” Curved Extrusion
Steps:
1) Attach Extrusions [14, 14a] to ends of Extrusions
[15, 15a] as indicated.
2) Insert Infills between Extrusions [14-15 & 14a-15a]
3) Connect Extrusions [11, 12, 13] between Extrusions
[14-15 & 14a-15a].
4) Attach Header to assembled frame
5) Connect Oval Graphic to Assembled frame (see Detail).
Graphic
Screw
Cap
V20
Graphic Attachment
Slide V20 connector into groove
of extrusion, then secure graphic
to connector using screw cap.
Detail

www.classicexhibits.com
Step 3
Page 3 of 3
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - LTK-1001 - Pedestal Assembly
QTY - 4
Standoffs
Shelf
Floor
When assembled
Steps
1) Use standoff screws to secure the front panel with
door and back panel of the pedestal to the side panels.
2) After assembling front, back, and side panels,
slide floor into the bottom of the pedestal. The
floor will sit on pins on the inside of the side panels.
3) After floor is in place, use velcro attachments to
install shelf
Countertop
Front Door Panel