Coaster 223423 User manual

ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
Fine Furniture for every stage of life
Dresser
223423
PAGE 1 OF 4
REVISION 0 : 02/10/2022 COASTERFURNITURE.COM

ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
WARNING!
2. This product is for home use only and not intended for commercial establishments.
ASSEMBLY TIME
ADRESSER 1PC
BLEG 4PCS
CSUPPORT LEG 1PC
COASTERFURNITURE.COM
ITEM:223423
PAGE 2 OF 4
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
PARTS IDENTIFICATION
5 MINUTES
HARDWARE IDENTIFICATION
1BOLT
(Φ5/16" x 22mm - RBW) 16PCS
2LOCK WASHER
(Φ5/16" - RBW) 16PCS
3FLAT WASHER
(Φ5/16" - RBW) 16PCS
4(4mm m - RBW) 1PC
ALLEN WRENCH

ASSEMBLY INSTRUCTIONS
STEP 1
COMPLETE
COASTERFURNITURE.COM
PAGE 3 OF 4
4
A
B
3
2
1
C
STEP 2
ITEM:223423

ANTI-TIPPING INSTALLMENT INSTRUCTIONS
FURNITURE TIPPING RESTRAINT
1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the short screw.
2. Determine where the furniture is to be placed and mark location on the wall for the mounting bracket
screw hole approximately 2" below the bracket mounted to the edge of the furniture.
3. Drill a 3/16" hole in the wall. Press the plastic wall plug into the hole and gently tap until the flange on
the wall plug is against the wall surface.
4. Position the bracket over the wall plug and use the long screw to securely attach the bracket to the wall.
5. Place the furniture so the bracket on the back edge is in line with the bracket on the wall.
6. Lace an end of the cable tie down through each bracket. Bring both ends together and slide the
beaded end of the cable tie through the keyhole shaped slot on the other end until snug. Pull down on
the beaded end until it snap locks into the keyhole slot.
7. To double lock return the beaded end back through the keyhole as shown.
8. Check to make sure the cable tie is securely laced and locked to the brackets.
COASTERFURNITURE.COM
PAGE 4 OF 4
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
Failure to detach this restraint before moving the furniture may result in injury and damage.
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
Failure to detach this restraint before moving the furniture may result in injury and damage.
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
Failure to detach this restraint before moving the furniture may result in injury and damage.
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
Failure to detach this restraint before moving the furniture may result in injury and damage.
ITEM:223423

COASTERFURNITURE.COM
Note: Dimension tolerance ±5%
INNER SIZE OF DRAWER A : 19.1'' X 13.2'' X 7.3''
INNER SIZE OF DRAWER B : 30.2'' X 13.2'' X 7.3''
10
ITEM:223423
18"
68"
38.8"
22"
A-11"
33.2"
B-11"
10.8"
4.7"
54.8"