Spectrum Industries 55396 User manual

Assembly Instructions
0190405 Page 1 of 2
Assembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts
or accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Wall Hanging Kit
for Collectiv8™Charging Pillar
55396
(4) 055699
1/4” x 1-1/4” Tapcon Hex
(For concrete walls)
(1) 0190174
#8 x 3/8” PHSM screw
(4) 0101381
#14 x 1-3/4” PHSM screw
(for wood stud walls)
(1) 0134543
L-bracket
(1) 0134531
Wall hanger bracket
• (1) 55396 kit will attach one unit to a wall
• Fasteners included for concrete wall applications
• To fully comply with ADA guidelines, it’s recommended the unit be hung
above base cabinets or other permanent structure that extends to the oor
Wall
1. Locate stud in wall. Position the wall hanger bracket at the
preferred height.
2. Level the bracket.
3. Using a drill with a Phillips driver, install the wall hanger bracket
onto the wall with (2) #14 x 1-3/4” PHSM screws. Figure 1.1.
Tighten securely.
Figure 1.2
Wall hanger bracket
(2) 0101381
#14 x 1-3/4” PHSM
Ratcheting
wrench
with 5/16”
socket
3/16”
Masonry
drill bit
Drill Phillips
driver
Tools Required
Hammer
drill
1. Position the wall hanger bracket at the preferred location and
height on the wall.
2. Level the bracket.
3. Mark the (2) mounting hole locations onto the wall.
4. Using a hammer drill with 3/16” masonry drill bit, drill into the
wall at the (2) marked locations. (Approximately 1-1/4”D).
5. Install the wall hanger bracket with (2) 1/4” x 1-1/4” Tapcon
fasteners. Figure 1.2. Tighten securely.
Tools Required
Figure 1.1
(2) #14 x
1-3/4” PHSM
Wall hanger bracket
(2) 1/4” x 1-1/4”
Tapcon Hex screw
Level
Level
1. Install wall hanger bracket
Wood stud wall Concrete wall
(2) 055699
1/4” x 1-1/4” Tapcon
Hex screw
Wall
Wall

Tools Required
Tools Required
Wall
0190405 Page 2 of 2
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2017 Spectrum Industries Inc., All rights reserved.
2. Install L-bracket and screw to wall
1. Attach the L-bracket to the top of the unit (using slotted hole)
with (1) #8 x 3/8” PHSM screw. Figure 2.
2. Install the 3rd #14 x 1-3/4” PHSM screw through the
L-bracket into the wall.
1. Attach the L-bracket to the unit (using slotted hole) with (1) #8 x 3/8”
PHSM screw. Figure 2.
2. Mark the L-bracket hole location onto the wall.
3. Lift the unit off the wall hanger bracket.
4. Using a hammer drill with 3/16” masonry bit, drill into the wall at the
marked location (approximately 1-1/2”D).
5. Place unit back onto wall hanger bracket
6. Install the 1/4” x 2-1/4” Tapcon Hex screw through the L-bracket.
(1) 0132697
1/4” x 2-1/4” Tapcon
Hex screw
(1) 0101381
#14 x 1-3/4” PHSM
Ratcheting
wrench
with 5/16”
socket
3/16”
Masonry
drill bit
Hammer
drill
Wood stud wall Concrete wall
(1) 0190174
#8 x 3/8” PHSM
screw
(1) 0190174
#8 x 3/8” PHSM
screw
L-bracket
Figure 4
Phillips
screwdriver
Drillor Phillips
driver
Phillips
screwdriver
Drillor Phillips
driver
(1) #14 x 1-3/4” PHSM
or
(1) 1/4” x 2-1/4” Tapcon
Hex screw
(1) 0190174
#8 x 3/8” PHSM
screw in slotted hole