croydon FRE2-25E001 A3 User manual

FRE2-25E001 A3
FRE2
FRE2
INSTRUCTION MANUAL
CROYDON
CROYDON
CROYDONMAQ INDUSTRIAL LTDA.
Estrada São Lourenço, 891 - Capivari - Duque de Caxias.
RJ - Brasil - CEP 25243-150 Fax: [phone]
Phone: [phone]
e-mail: [email protected]
CHICKEN ROTISSERIE 2 SKEWERS - MODEL: FRE2-25E001 A3
- Please read these instructions carefully before operating this appliance.
- This appliance is designed to operate on alternative current (A.C.) Only
- DO NOT CONNECT TO DIRECT CURRENT (D.C.).
- Care should be taken when operating this appliance, as HOT SURFACES may cause burns.
- The installation area must be well ventilated to eliminate gases resulting of process.
- It’s recommended to have at least 10 “ of free space around the equipment.
- For safety reasons DO NOT install the equipment next of combustible materials.
- When not in use for long period unplug the appliance.
-As metallic parts are good conductors of heat, let it cool before handling.
INSTALLATION
- Unpack the equipment and remove the accessories from the internal part.
- Position the equipment in the point of installation and adjust the feet to regulate the closing of the
doors.
- Make the electric installation according to your local safety standards.
- Check the equipment requirements and your power supply conditions and connect it.
-Always connect the green head screw ( ) to ground.
OPERATION
- Check if all thermostats’ knobs are in "off" position.
- Place the skewers on the equipment.
- Turn on the Motor switch located at the left side of the frontal panel (inferior button)
- Turn each thermostat’s knob to the desired temperature.
- Wait about 1 hour, with skewers rotating, for the chickens to be finished.
- You can adjust each thermostat independently to get the results that you wish.
- It’s recommended to use a layer of water in the tray (the enough to cover the bottom) to avoid the
splash of grease and to facilitate the cleaning operation.
CLEANING PROCEDURE
- Remove the skewers and clean it with soaped water after the heavy fat was removed.
- Avoid to wet the electric connections of the heaters.
- Clean the cabinet with a cloth humidified with soaped water.
- Do not use any kind of abrasive material for cleaning.
- Do not use water jet on the equipment.
- Connect a tube or place a recipient under the drain valve.
- Remove the cap of the drain located in the inferior part for the discharge of every residue of water
and fat.
MAINTENANCE
- A little periodical maintenance is needed to get a best performance of the equipment:
- Always maintain your equipment clean and in perfect operation conditions, those providences will
help your equipment to last longer.
- To guarantee a good performance, we recommended an annual revision of the equipment.

39
39
Upper Back Cover
Lower Back Cover
Burner’s Panel
Thermostat
Pilot Lamp
Thermostat Support
External Left Cover
Thermal Insulator
Internal Left Cover
Skewer’s Support
Temperate Glass
Skewer’s tool
Motor
Nut (1/4")
Rubber Washer
Screw.(1/4")
Endless Screw
Allen Screw (1/4")
Tray
Foot
Structure
Frontal Forehead
Internal Right Cover
Internal Top Cover
Top Cover
Thermal Insulator
Top Right Cover
Thermal Insulator
Screw (1/4")
External Right Cover
Door Handle
Screw
Door Rail
Lighter Protection
Limit Ring
Cord Retainer
Axis Guide
Door Spring
Screw
Mechanism Protection Box
Motor Cover
Drain Valve
Skewer Gear
Skewer with Handle
Screw (1/4")
Double Hook
Single Hook
Heater’s Support
Glass Door Handle
Tempered Glass with Hole
Wire Connector
Knob
Cover Protection
Heater
Lower Front Cover
Door Hinge
Eletric Connector
Gear Protection
Wiring
On/Off Switch
Celleron Gear
Endless Screw
Door
Washer (3/8”)
Axis
Skewers Support
Screw
Washer (1/4”)
Nut (3/8”)
Heating Element Retainer
Temperature Dial
Cord Connection
Rubber Finishing
Thermostat Screw
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
94.414-3
94.207-3
94.224-3
2.070-3
2.013-3
94.057-3
94.203-3
94.216-3
94.222-3
94.035-3
94.250-3
94.069-3
94.056-3
601
94.088-3
345
94.062-3
531
94.058-3
2.088-3
94.219-3
94.004-3
94.227-3
94.052-3
94.044-3
94.007-3
94.005-3
94.217-3
381
94.230-3
94.060-3
355 C
94.418-3
94.226-3
94.034-3
9.413-3
94.027-3
94.067-3
557
94.002-3
94.047-3
94.032-3
94.031-3
94.014-3
332
94.019-3
94.020-3
94.070-3
37.022-3
94.251-3
2.085-3
2.009-C
94.073-3
94.074-3
94.003-3
94.029-3
94.229-3
94.225-3
94.228-3
258
94.059-3
94.033-3
94.211-3
593
94.214-3
94.220-3
355 G
597
606
94.117-3
1.360-3
2.193-3
3.021-3
331
26
51
20
24
21
23
28
22
38
19
9
10
8
7
25
3
2
1
27
36
30
29
31
56 32
66
65
62
33
37
35
40
39
41
13
17
16
14
18
42
44
43
46
45
47
11
50
12
55
33
60
32
63
32
49
29
15
35
18
61
Item Code Description
67
67
67
CROYDON
CROYDON
68
68
68
69
64
Technical Data
FRE2-25E001 A3
Voltage (V)
Electric
Power (w)
Weight (kg/lbs)
Dimension W x H x D (cm/in)
Capacity
220
190
2800
44.1 / 97
114 /44.9 x 84/33.1 x 46/18.2
10 chicken (2 skewers)
Skewer Movement
Heaters
34
552
6
4
48
53
57
54
58
59
Wiring Diagram
HEATER THERMOSTAT
MOTOR
SWITCH
1 2 3 4
220V
10
220V. parallel
3
12
220 V. heater
4
CHICKEN ROTISSERIE 2 SKEWERSCHICKEN ROTISSERIE 2 SKEWERS
70
71
72
73
74