CTM LYNG 5648534 Guide

Timer, wireless
165
INSTALLATION
CTM Lyng AS is Norway’s leading manufacturer
and supplier of security products for the home,
assistive technology, energy efficiency, and light
and heating control for all building types under the
mKomfy
®
, mTouch
®
, Microsafe
®
and Centrol
®
brands.
Wedistribute our products through wholesalers.
Weoffer everything from product development to
productionanddistribution.
Our production facility in Vanvikan is equipped with some
of the most advanced machinery in Europe.
Verkstedvegen 19, 7125 Vanvikan, Norway
Tel: [phone]
Email: [e-mail]
Thank you for choosing a product from CTM Lyng AS
For more information, visit us at
www.ctmlyng.com
Installation and User instructions
0320 Art. No.: 12974_EN
Technical data
Dimensions:
Conforms to RS16
IP Code:
20
Battery:
CR2032
Battery life:
5 years in
normaluse
RF:
868.100 MHz +5 dBm
Compatible with “v2”
equipment, see page 2
RF range:
30 metres
NB: It is best to carry out pairing and test the timer before
installation. Mount the switch directly on the wall or on the
outside of a standard wall box.
DIPSW
ANNUAL END USER TEST
The system owner/user must familiarise themselves with
the accompanying Installation and User Instructions at
installation, and is under an obligation to test that installed
equipment shuts off the water supply as required in the
Norwegian Insurance Approval Board (FG) test.
Function testing must be performed at least twice a year in
accordance with the Installation and User Instructions for
sensors and switch panels.
Back of
timer
ON
OFF
TIP: Program all the units in a system before mounting. This will
make it easier to test the equipment.
Factory settings:
1=ON 2=ON 3=OFF 4=OFF
*DIP 3 – Master switch function/Lock function
If DIP3=ON, only this switch panel can turn paired products back on if
they have been turned off with this switch panel.
Example: A school kitchen wants to use a timer for all its cookers. All the cookers
also have a cooker guard. The teacher starts all the cookers by pressing the switch
panel (DIP3=ON) with the time set to 1 hour. All the cookers now have power for
1 hour. If the cooker guard cuts the power, the pupils can press the cooker guard
and get power back. After 1 hour, the switch panel turns all the cooker guard
sockets off. Now no pupil can turn the cooker on by pressing the cooker guard.
**DIP 4 – Time of choice
DIP1 and 2 must be OFF.
To change the time of choice, set DIP4=ON. Briefly pressing SW4 once
changes to the next time. The sensor acknowledges with the number
of beeps and flashes (LED3) for the time selected.
NB: Set DIP4 back to OFF once the desired time has been selected.
DIP 1 DIP 2 DIP 3* DIP 4** Time
ON ON ON:
Lock function
OFF:
Normal use
ON:
Set time of choice
NB! Must be
OFF when in
operation.
30 minutes
OFF ON 1 hour
ON OFF 4 hours
OFF OFF Time of choice**
SOUND TIME
1 beep 5 min.
2 beeps 15 min.
3 beeps 20 min.
4 beeps 45 min.
5 beeps 60 min.
SOUND TIME
6 beeps 90 min.
7 beeps 2 hours
8 beeps 4 hours
9 beeps 6 hours
10 beeps 10 hours
No. 5648534 / 6251645
SW4
LED3

432
USER INFORMATION EVERYDAY USE
The Timer is a security product from CTM Lyng AS.
The timer controls the power supply to sockets it is
paired with, and where appropriate, the water
supply to the dwelling, individual rooms and
relevant consumer electronics/
appliances.
Compatible with newer
“R” / ”Radio” products, e.g.:
• mKomfy cooker guards
• Mstikk sockets
• Aqua Xpress valve drivers
The system is flexible, and can
be expanded to accommodate
different needs and security levels.
If several timers are used with the same socket/
valve, it is always the longest time that counts.
Example: The timer is set to 1 hour and is
activated. Someone goes into the bathroom and
this is detected by the motion sensor. It is set
to 5minutes. The valve will not close for 1 hour
because of the timer, however.
If the timer is installed together with an On/Off
switch, it is important to be aware that paired
products will remain on/open until activated by the
On/Off switch.
For the products to work on the timer again, the timer
must be operated after the On/Off switch has
been used.
This problem can be solved by activating the lock
function for the timer, set DIP3=ON (see page 5).
Then only the timer will be able to turn on or open
paired products. NB: Interoperability with motion
sensors will not be possible when the lock function
is activated.
PAIRING
1. Activate pairing mode in the product that
is to be paired with the timer.
2. To send a pairing signal from the timer,
briefly press SW4 on the back of the timer.
3. Test whether pairing has been successful
by operating the timer.
Back of timer
SW4
TIMER FUNCTION CHANGING THE BATTERY
The timer ensures that power, or water, is only
supplied to connected units for the required
period. The operating period can be extended
with a quick press of the button, which will
restartthetime.
Look for products
labelled “v2”
Start countdown
Cancel
Back of timer
The battery (CR2032) will need changing
approximately every 5 years in normal use.
1. Lever the front off with
a small screwdriver.
2. Slide the old battery out
and insert a new one.
TESTING COMMUNICATION
To test communication between the timer and
socket/valve driver, briefly press the button on
thetimer.
The blue radio communication LED in the socket/
valve driver will flash to acknowledge every press
ofthe button.