CTS CVT-3002-PLUS SERIES User manual

Trademarks
CTS is a registered trademark of Connection Technology
Systems Inc. Contents subject to revision without prior notice.
All other trademarks remain the property of their owners.
Copyright Statement
Copyright Connection Technology Systems Inc.
This publication may not bereproducedas awholeor in part, in
any way whatsoever unless prior consent has been obtained
from Connection Technology Systems Inc.
FCC Warning
The CVT-3002-PLUS Series converters have been tested and
found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These standards are
designed to provide reasonable protection against harmful
interference when these devices are operated in a commercial
environment. These devices generate, use, and can radiate
radio frequency energy and may cause harmful interference to
radio communications unless installed in accordance with this
User’s Guide. Operation of these devices in a residential area
is likely to cause harmful interference which will make the user
responsible for the appropriate remedial action at his / her own
expense.
CE Mark Warning
These are Class A products. In a domestic environment these
products may cause radio interference in which case the user
will need to consider adequate preventative methods.
1. Checklist
The package should contain the following items:
-
CVT-3002-PLUS Converter
-
AC-DC Power Adapter
-
User’s Guide
Please notify your sales representative immediately if any items
are missing or damaged.
2. Overview
CVT-3002-PLUS is designed to meet the massive needs for
Gigabit network deployment and able to extend a copper based
Gigabit network via fiber cable to a maximum distance up to
80KM.
CVT-3002-PLUS is fully compliant with IEEE802.3, 802.3u,
802.3ab & 802.3z standards. It can be installed into a CVT
Converter RACK. The installation & operation procedures are
simple & straightforward. Operation status can be locally
monitored through a set of Diagnostic LED located in the front
panel.
Major Features:
-
Auto-Negotiation in TX port
-
MDI/MDIX Auto-Crossover supported
-
Support Flow Control
-
Support Link Alarm
-
Support Jumbo Frame 9K bytes (under 10,100,1000Mbps)
-
Store and Forward Switching Mechanism
-
Support Auto & Force mode configuration
3. Installation

Attach fiber cable from the CVT-3002-PLUS to the fiber
network. The fiber connections must be matched –transmit
socket to receive socket.

Attach a UTP cable from the 10/100/1000BASE-T network
to the RJ-45 port on the CVT-3002-PLUS.

Connect the power adapter to the CVT-3002-PLUS and
check that the Power LED lights up. The TX Link/Act and
F/O Link/Act LEDs will light up when all the cable
connections are satisfactory.
Figure 1. CVT-3002-PLUS dual fiber Front Panel
Figure 2. CVT-3002-PLUS WDM & SFP Front Panel
Figure 3. CVT-3002-PLUS Converter Rear Panel
4. DIP SWITCH Setting
The default setting for PIN 1 and 6 is ON. The rest of Pins are
OFF.
Pin NO.
Function
OFF
ON
1
TP Auto-Negotiation
Disable
Enable
2
Manual TP speed
10M
100M
3
Manual TP speed
N/A
1000M
4
Duplex mode
Half
Full
5
Flow Control
Disable
Enable
6
F/O mode
Force
Auto
7
Link Alarm
Disable
Enable
8
Reserved
-
-
NOTE:
1.Before changing TP speed, duplex mode and flow
control setting, please make sure PIN 1 is set to OFF.
2. When TP speed is set to 10M or 100M manually, PIN 3
needs to be turned OFF.
3. Under 1000Mbps, it supports full-duplex mode only.

5. LED Description
6. Technical Specifications
Standards
IEEE 802.3, 802.3u, 802.3ab,
802.3z
Interface
1 X 10/100/1000 RJ-45 connector
1 X 1000 F/O port or SFP Slot
LED
Power, FDX, Status, Speed,
FO Link/ACT, TX Link/ACT
Power
I/P AC 100-240V
O/P DC 5V
Power Consumption
2.2W
Weight
0.6KG
Dimensions
71mm(W)X94mm(D)X26mm(H)
Temperature
Operating: 0o~50oC
Storage: -20o~60oC
Humidity
5%~90% RH non-condensing
Certification
FCC/CE Class A
Media
TP:
EIA/TIA-568 CAT 5e,
1000M
Fiber:
50/125 or 62.5/125  m
multi-mode
9/125 or 10/125  m
single-mode
* Please contact us for further reports and updates.
NOTE: Specifications may change without prior notice.
7. Fiber Transceiver Information
Dual Rate
2 Wave-Length WDM
TYPE
W2A(SM-10)
W2B(SM-10)
Connector Type
SC
SC
Wavelength
1310/1550nm
1550/1310nm
Typical Distance
10 Km
10 Km
Min TX PWR
-10.0dBm
-10.0dBm
Max TX PWR
-3.0dBm
-3.0dBm
Sensitivity
-20.0dBm
-20.0dBm
Link Budget
10.0dB
10.0dB
1000M
Multi-Mode/Single-Mode
TYPE
BTFC
BTFC
(SM-10)
BTFC
(SM-20)
BTFC
(SM-30)
BTFC
(SM-50)
BTFC
(SM-80)
Connector
Type
SC
SC
SC
SC
SC
SC
Wavelength
850nm
1310nm
1310nm
1310nm
1550nm
1550nm
Typical
Distance
550m
10 Km
20 Km
30 Km
50 Km
80 Km
Min TX PWR
-9.5dBm
-9.5dBm
-9.0dBm
-5.0dBm
-5.0dBm
0dBm
Max TX
PWR
-1.5dBm
-3.0dBm
-2.0dBm
3.0dBm
3.0dBm
5.0dBm
Sensitivity
-17.0dBm
-20.0dBm
-23.0dBm
-24.0dBm
-24.0dBm
-24.0dBm
Link Budget
7.5dB
10.5dB
14.0dB
19.0dB
19.0dB
24.0dB
2 Wave-Length WDM
TYPE
W2A
(SM-10)
W2B
(SM-10)
W2A
(SM-20)
W2B
(SM-20)
W2A
(SM-40)
W2B
(SM-40)
Connector
Type
SC
SC
SC
SC
SC
SC
TX
Wavelength
1310nm
1550nm
1310nm
1550nm
1310nm
1550nm
RX
Wavelength
1550nm
1310nm
1550nm
1310nm
1550nm
1310nm
Typical
Distance
10 Km
10 Km
20 Km
20 Km
40 Km
40 Km
Min TX
PWR
-10.0dBm
-10.0dBm
-9.0dBm
-9.0dBm
-5.0dBm
-5.0dBm
Max TX
PWR
-3.0dBm
-3.0dBm
0 dBm
0 dBm
3.0dBm
3.0dBm
Sensitivity
-22.0dBm
-22.0dBm
-23.0dBm
-23.0dBm
-23.0dBm
-23.0dBm
Link Budget
12.0dB
12.0dB
14.0dB
14.0dB
18.0dB
18.0dB
NOTE: Specifications may be changed without prior notice.
Contact Information
Connection Technology Systems INC (CTS)
18F-6, No.79, Sec.1, Xintai 5th Rd., Xizhi Dist.,
New Taipei City 221, TAIWAN, R.O.C.
TEL: [phone] FAX: [phone]
E-Mail: i[email protected]om
CVT-3002-PLUS
SERIES
10/100/1000BASE-T to
1000BASE-X Standalone
Media Converter
User’s Guide
Version 1.0
LED
Color
Function
Power
Green
Lit when power is available.
TX
Link/Act
Green
Lit when TX cable connection with
remote device is good.
Blink when TX traffic is present.
FO
Link/Act
Green
Lit when Fiber cable connection with
remote device is good.
Blink when F/O traffic is present.
FDX
Green
Lit when TX works in Full-Duplex.
Not-Lit when TX works in Half-Duplex.
Speed
Green
No-Lit when TX works in 10M.
Lit when TX works in 100M.
Orange
Lit when TX works in 1000M.
Status
Green
Lit when TX and F/O link is up.
Orange
Lit when TX or F/O link is down.