CTS MCT-3002 Series User manual

Trademarks
CTS is a registered trademark of Connection Technology
Systems Inc. Contents subject to revision without prior
notice.
All other trademarks remain the property of their owners.
Copyright Statement
Copyright Connection Technology Systems Inc.
This publication may not be reproduced as a whole or in
part, in any way whatsoever unless prior consent has been
obtained from Connection Technology Systems Inc.
FCC Warning
The MCT-3002 Series converters have been tested and
found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These standards are
designed to provide reasonable protection against harmful
interference when these devices are operated in a
commercial environment. These devices generate, use,
and can radiate radio frequency energy and may cause
harmful interference to radio communications unless
installed in accordance with this User’s Guide. Operation
of these devices in a residential area is likely to cause
harmful interference which will make the user responsible
for the appropriate remedial action at his / her own
expense.
CE Mark Warning
These are Class A products. In a domestic environment
these products may cause radio interference in which case
the user will need to consider adequate preventative
methods.
1. Checklist
The MCT-3002 package should contain the following
items:
-
MCT-3002 Converter
-
AC-DC Power Adapter
-
This User’s Guide
Please notify your sales representative immediately if any
items are missing or damaged.
2. Overview
The MCT-3002 series media converter converts traditional
twisted-pair RJ-45 cable into various fiber media including
multi-mode, single-mode, SC connector, bi-directional WDM,
or a SFP slot for pluggable fiber transceiver, extending
transmission distance for the deployment to the household,
apartment or campus.
MCT-3002 series media converter is fully compliant with IEEE
802.3, 802.3u, 802.3ab & 802.3z standards. Besides, it is
equipped with some switching features including store and
forward. Operation status can be locally monitored through a
set of Diagnostic LED located in the front panel.
Major Features:
-
Auto-Negotiation in TP port
-
MDI/MDI-X Auto-Crossover supported
-
Support Link Alarm
-
Support Jumbo Frame 9K bytes (under 10,100,1000Mbps)
-
Store and Forward Switching Mechanism
-
Support Auto & Force mode configuration
3. Installation

Attach a fiber cable from MCT-3002 to the fiber network.
The fiber connections must be matched –transmit socket to
receive socket.

Attach a UTP cable from the 10/100/1000BASE-T network
to the RJ-45 port on MCT-3002.

Connect the power adapter to MCT-3002 and the
PWR/STA LED will light up. The TP and F/O LEDs will light
up as soon as if all the cable connections are satisfactory.
4. DIP SWITCH Setting
The default setting for PIN 1 through 7 is ON and PIN 8 is OFF.
PIN NO.
Function
OFF
ON
1
TP Auto-Negotiation
Disable
Enable
2
Manual TP speed
Please refer to
NOTE 3,4 and 5
3
4
Fiber Speed
Manual
Auto-
Sensing
5
Fiber Manual Speed
100M
1000M
6
F/O mode
Force
Auto
7
N/A
N/A
N/A
8
Link Alarm
Disable
Enable
NOTE:
1.Before adjusting the configuration of the DIP Switch, the
power should be unplugged.
2.Disable TP Auto-Negotiation function before configuring
TP speed manually.
3.The TP speed is fixed in 10Mbps when PIN 2 & 3 are both
set to ON or OFF.
4.The TP speed is fixed in 100Mbps when PIN 2 is set to ON
and PIN 3 is set to OFF.
5.The TP speed is fixed in 1000Mbps when PIN 2 is set to
OFF and PIN 3 is set to ON.
6.Under TP speed 1000Mbps, it supports full-duplex mode
only.
7.PIN 4 & PIN 5 are for dual rate model (MCT-3002-DR)
only.
Fig. 1 Dual Fiber Front Panel of MCT-3002 Converter
Fig. 2 WDM & SFP Front Panel of MCT-3002 Converter
Fig. 3 Rear Panel of MCT-3002 Converter
Fig. 4 Side Panel of MCT-3002 Converter

5. LED Description
LED
Color
Function
PWR/STA
Green
Lit when power is available.
TP
Green
Lit when TP cable connection with
remote device is good.
Blinking when TP traffic is present.
F/O
Green
Lit when Fiber cable connection at
100M with remote device is good.
Blinking when F/O traffic is present.
(For dual rate model only)
Orange
Lit when Fiber cable connection at
1000M with remote device is good.
Blinking when F/O traffic is present.
FDX
Green
Lit when TP works in full-duplex.
Off when TP works in half-duplex.
SPD
Green
Lit when TP works in 10M.
Lit when TP works in 100M.
Orange
Lit when TP works in 1000M.
6. Technical Specifications
Standards
IEEE 802.3, 802.3u, 802.3ab,
802.3z
Interface
1 X RJ-45 connector
1 X F/O port or SFP Slot
LED
Power/Status, FDX, Speed, F/O,
TP
Power
I/P AC 100-240V
O/P DC 3.3V
Power Consumption
2.3W
Weight
0.1Kg
Dimensions
51mm(W)X74mm(D)X20mm(H)
Temperature
Operating: 0o~50oC
Storage: -20o~60oC
Humidity
5%~90% RH non-condensing
Certification
FCC/CE Class A
Media
TP:
EIA/TIA-568 CAT 5e,
1000M
Fiber:
50/125 or 62.5/125  m
multi-mode
9/125 or 10/125  m
single-mode
* Please contact us for further reports and updates.
NOTE: Specifications may change without prior notice.
7. Fiber Transceiver Information
Dual Rate:
TYPE
BTFC
(SM-10)
W2A
(SM-10)
W2B
(SM-10)
Connector Type
SC
SC
SC
Wavelength
1310nm
1310/1550nm
1550/1310nm
Typical Distance
10Km
10Km
10Km
Min TX PWR
-9.5dBm
-10.0dBm
-10.0dBm
Max TX PWR
-3.0dBm
-3.0dBm
-3.0dBm
Sensitivity
-20.0dBm
-20.0dBm
-20.0dBm
Link Budget
10.5dB
10.0dB
10.0dB
1000M:
- Multi-Mode/Single-Mode
TYPE
BTFC
BTFC
(SM-10)
BTFC
(SM-20)
BTFC
(SM-30)
Connector Type
SC
SC
SC
SC
Wavelength
850nm
1310nm
1310nm
1310nm
Typical Distance
550m
10Km
20Km
30Km
Min TX PWR
-9.5dBm
-9.5dBm
-9.0dBm
-5.0dBm
Max TX PWR
-1.5dBm
-3.0dBm
-2.0dBm
3.0dBm
Sensitivity
-17.0dBm
-20.0dBm
-23.0dBm
-24.0dBm
Link Budget
7.5dB
10.5dB
14.0dB
19.0dB
- 2 Wave-Length WDM
TYPE
W2A
(SM-10)
W2B
(SM-10)
W2A
(SM-20)
W2B
(SM-20)
W2A
(SM-40)
W2B
(SM-40)
Connector
Type
SC
SC
SC
SC
SC
SC
TX
Wavelength
1310nm
1550nm
1310nm
1550nm
1310nm
1550nm
RX
Wavelength
1550nm
1310nm
1550nm
1310nm
1550nm
1310nm
Typical
Distance
10Km
10Km
20Km
20Km
40Km
40Km
Min TX
PWR
-10.0dBm
-10.0dBm
-9.0dBm
-9.0dBm
-5.0dBm
-5.0dBm
Max TX
PWR
-3.0dBm
-3.0dBm
0dBm
0dBm
3.0dBm
3.0dBm
Sensitivity
-22.0dBm
-22.0dBm
-23.0dBm
-23.0dBm
-23.0dBm
-23.0dBm
Link Budget
12.0dB
12.0dB
14.0dB
14.0dB
18.0dB
18.0dB
NOTE: Specifications may be changed without prior notice.
Contact Information
Connection Technology Systems INC (CTS)
18F-6, No.79, Sec.1, Xintai 5th Rd., Xizhi Dist.,
New Taipei City 221, TAIWAN, R.O.C.
TEL: [phone] FAX: [phone]
E-Mail: [email protected]
MCT-3002 SERIES
10/100/1000BASE-T to
1000BASE-X or
100/1000BASE-X
Standalone Media Converter
User’s Guide
Version 1.2