CUMMINS ALLISON JetCount 4020 User manual

JetCount®
Currency Counter
Operating Instructions
for All Models

Power Specifications
Power Requirements
•Voltage operating range: 105-130 VAC or 198-253 VAC, manual switching
•Frequency:50/60 Hz
•Electrical supply circuit: The customer must provide a single-phase, dedicated power line that
meets the machine’s power rating(s). Use a properly grounded circuit breaker in compliance with
applicable local electrical code.
Power Rating(s)
•Full load amps (FLA): .6A/.3A
Power disruptions and fluctuations causing input voltage other than listed in power requirements
can lead to improper operation of this device, damage to electrical components, and failure. Such
occurrences are not covered under the machine warranty or preventative maintenance agreement for this
device. Power conditioning/stabilizing devices are available for purchase from Cummins-Allison Corp.
High voltage inside. Risk of electric shock.
Turn power
OFF
and unplug power cord from machine before cleaning.
Do not attempt repairs. Repairs must be made by authorized Cummins-Allison
Corp. personnel.
Plug three-prong grounded plug (supplied) into properly grounded three-prong
outlet.
Read and understand all instructions before use.
Improper voltage levels can cause equipment malfunction, damage electrical
components, and void warranty.
Provide separate circuit serving only this device to ensure proper operation.
Follow listed power requirements to ensure proper operation.
Provide power conditioning/stabilizing devices if necessary.

Statement of Agency Compliance
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Class A Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case
the user will be required to correct the interference at his own expense.
Any changes or modifications made to this device that are not expressly approved by Cummins-Allison
Corp. may void the user’s authority to operate the equipment.
To maintain compliance with FCC rules and regulations, cables connected to this device must be
shielded cables in which the cable shield wires are grounded (tied) to the connector shell.
Safety Compliance
U.L. 60950, Third Edition and CAN/CSA – C22.2 No. 950-95
•U.L. file number: E135004 NWGQ Information Technology Equipment Including Electrical
Business Equipment
The CE mark on the product indicates that the system has been tested to and conforms to the
provisions noted within the 2004/108/EC (EMC) and 2006/95/EC (LVD) directives.
EN 60950-1 European Norm, Safety of Information Technology Equipment Including Electrical
Business Equipment
022-7200-00 – Rev. C04/2012
Radio frequency present.
Install and operate per manuals to avoid radio interference.
Unapproved changes to machine may void user’s right to operate.
Do not modify without express permission from Cummins-Allison Corp.
Attach only shielded cables with shield wires grounded (tied) to connector shell.

JetCount®Currency Counter All Models
2
Table of Contents
POWER SPECIFICATIONS .............................................................. INSIDE FRONT COVER
STATEMENT OF AGENCY COMPLIANCE........................................................................... 1
FCC CLASS A COMPLIANCE STATEMENT ........................................................................ 1
SAFETY COMPLIANCE....................................................................................................... 1
GETTING TO KNOW YOUR JETCOUNT®CURRENCY COUNTER....................................... 4
THE JETCOUNT CURRENCY COUNTER ............................................................................. 5
MODEL 4020 CONTROL PANEL ..............................................................................................5
Key Explanation ............................................................................................................5
MODEL 4021, 4022 CONTROL PANEL...................................................................................6
Key Explanation ............................................................................................................6
ALL MODELS:KEY NUMBERS ..................................................................................................7
ALL MODELS:KEY-TOP KIT OPTION .........................................................................................7
Key Explanation ............................................................................................................8
THE BASICS ....................................................................................................................... 9
POWER...................................................................................................................................9
HOPPER .................................................................................................................................9
DENSITY OPERATION...............................................................................................................9
SETTING SD DETECTION ....................................................................................................... 10
THICKNESS ADJUSTMENT DIAL.............................................................................................. 11
OPERATING MODES ............................................................................................................. 11
Choosing a Mode of Operation ................................................................................ 11
MEMORY LEVELS ................................................................................................................. 12
SETTING STRAP LIMITS......................................................................................................... 12
PRINTED REPORTS............................................................................................................... 13
Setup Report............................................................................................................... 13
HOW TO USE COUNT MODE............................................................................................16
PROCESSING DOCUMENTS.................................................................................................... 16
DIRECT ACCESS STRAPPING ................................................................................................. 17
BATCH ACCUMULATION,ADD KEY OFF ................................................................................ 17
BATCH ACCUMULATION,ADD KEY ON ................................................................................. 18
HOW TO USE VALUE MODE ............................................................................................20
PROCESSING DOCUMENTS.................................................................................................... 20
BATCH ACCUMULATION,ADD KEY OFF ................................................................................ 21
BATCH ACCUMULATION,ADD KEY ON ................................................................................. 22
SPECIAL MODE MENU ....................................................................................................24
ENTERING THE SPECIAL MODES MENU.................................................................................. 24
SETUP FIELDS...................................................................................................................... 25
Default Type................................................................................................................ 27
Audio Alarm Status.................................................................................................... 28
Speed........................................................................................................................... 28
Port 1 Status and Port 2 Status............................................................................... 28
Key Lockout ................................................................................................................ 28
Comm Report ............................................................................................................. 29
Options ........................................................................................................................ 29
SD Function Control................................................................................................... 29
Function Key Setting ................................................................................................. 30

© 2012 Cummins-Allison Corp.
3
Printer Type................................................................................................................. 30
Setup Report............................................................................................................... 30
Remote Display Count .............................................................................................. 31
REFERENCE .....................................................................................................................32
DAILY CLEANING PROCEDURES............................................................................................. 32
Recommended Cleaning Materials......................................................................... 32
Daily Cleaning............................................................................................................. 32
STOPPING CONDITIONS AND RECOVERY STEPS...................................................................... 36
MACHINE SPECIFICATIONS.................................................................................................... 38
MACHINE OPTIONS............................................................................................................... 38
GLOSSARY........................................................................................................................... 39
Safety Messages and Advisories............................................................................. 39
Terms ........................................................................................................................... 39
WARRANTY INFORMATION ............................................................................................41
EQUIPMENT WARRANTY ....................................................................................................... 41
SOFTWARE WARRANTY ........................................................................................................ 41
DISCLAIMER AND LIMITATION OF LIABILITY ............................................................................ 42

JetCount®Currency Counter All Models
4
Getting to Know Your JetCount®Currency Counter
Thank You
Thank you for selecting the JetCount®currency counter from Cummins Allison.
For Your Records
Please fill in the following information for easy reference.
Model No.
Serial No.
Your Local
Cummins Allison
Office
Address:
Phone:
JetCount®Features
This manual covers all of the available features and functions for the JetCount currency counter.
However, your particular unit may or may not be equipped with every option.
(To learn more, see Machine Specifications and Options.)
Recommended Maintenance
(To learn more, see Daily Cleaning Procedures.)

© 2012 Cummins-Allison Corp.
5
The JetCount®Currency Counter
This manual is designed to provide the new user with a detailed description of the various features and
modes of operation for the JetCount currency counter models 4020, 4021 and 4022.
Model 4020 Control Panel
Key Explanation
Key
Description
RESET This key is used when clearing counts and to restart the machine after a stopping
condition.
DENSITY This key is used for setting doubles detection sensitivity by denomination.
STRAP
This key is used for setting a Strap Limit at any preset value (5, 10, 20, 25, 50,
75, 100 or infinity). This key is also used to set strap values at levels other than
the preset values (i.e., 53, 79, etc.)
SPEED This key is used to set speed at *(low), ** (medium) or *** (high).
ADD This key is used for accumulating a total even after notes have been removed
from the stacker. When disabled, totals clear each time the stacker is emptied.
Strap Density Denomination
Add SD
RESET DNSTY STRAP
Count Speed
SPEED ADD

JetCount®Currency Counter All Models
6
Model 4021, 4022 Control Panel
Key Explanation
Key
Description
RESET This key is used when clearing counts and to restart the machine after a stopping
condition.
DENSITY This key is used for setting doubles detection sensitivity by denomination.
STRAP
This key is used for setting a Strap Limit at any preset value (5, 10, 20, 25, 50,
75, 100 or infinity). This key is also used to set strap values at levels other than
the preset values (i.e., 53, 79, etc.)
SD This key is used to activate suspect document detection and set sensitivity by
denomination.
SPEED This key is used to set speed at *(low), ** (medium) or *** (high).
ADD This key is used for accumulating a total even after notes have been removed
from the stacker. When disabled, totals clear each time the stacker is emptied.
Strap Density Denomination
Add SD
Count Speed
RESET DNSTY STRAP
SD SPEED ADD

© 2012 Cummins-Allison Corp.
7
All Models: Key Numbers
Instructions shown on the display refer to “key” numbers. Key positions are as follows:
All Models: Key-Top Kit Option
All JetCount models may be upgraded with an optional key-top kit that includes:
•VALUE keys.
•DENOM keys.
•Direct Access Strapping keys*. These keys are used for setting a Strap Limit at any
preset value from five to 100 in increments of five.
•Direct Access Denomination keys*. These preset denomination keys ($1, $2, $5,
$10, $20, $50, $100) are used as a multiplier when JetCount is in VALUE mode.
* Strapping and denomination keys are mutually exclusive and cannot be simultaneously
engaged.
To order the key-top kit, contact a Cummins Allison representative.
Direct Access Strapping Keys (One Sample Configuration Shown)
Strap Density Denomination
Key 7 Key 8 Key 9 Key 10 Key 11 Key 12
RESET DNSTY STRAP
Count Speed
SPEED ADD
Key 13 Key 14 Key 15
Key 1 Key 2 Key 3
Key 4 Key 5 Key 6
Strap Density Denomination
Add SD
5 10 25 40 50 75
Count Speed
RESET DNSTY STRAP
SD SPEED ADD
100 DENOM VALUE

JetCount®Currency Counter All Models
8
Direct Access Denomination Keys
Key Explanation
Key
Description
RESET This key is used when clearing counts and restarts the machine after a stopping
condition.
DENSITY This key is used for setting doubles detection sensitivity by denomination.
STRAP
This key is used for setting a Strap Limit at any preset value (5, 10, 20, 25, 50,
75, 100 or infinity). This key is also used to set strap values at levels other than
the preset values (i.e., 53, 79, etc.)
SD
For models equipped with Magnetic SD (JetCount model 4021) or Magnetic and
UV/FL SD (JetCount model 4022), this key is used to activate suspect document
detection and set sensitivity by denomination.
SPEED This key is used to set speed at *(low), ** (medium) or *** (high).
ADD This key is used for accumulating a total even after notes have been removed
from the stacker. When disabled, totals clear each time the stacker is emptied.
DENOM This key is used to select the denomination that will be used to count currency.
VALUE This key is used to toggle between count and note values.
Strap Density Denomination
Add SD
$1 $5 $10 $20 $50 $100
Count Speed
RESET DNSTY STRAP
SD SPEED ADD
$2 DENOM VALUE