CyberData 011410 Manual

Quick Reference 931332C © 2019, CyberData Corporation, ALL RIGHTS RESERVED© 2019, CyberData Corporation, ALL RIGHTS RESERVED 931332C Quick Reference
Typical System Installation
Getting Started
• Download the Operations Guide PDF file, from the Downloads tab at the following webpage:
https://www.cyberdata.net/products/011410
• Create a plan for the locations of your Intercoms.
• WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
•WARNING: This enclosure is not rated for any AC voltages!
Parts
Parameter Factory Default Setting
IP Addressing DHCP
IP Addressa
a. Default if there is not a DHCP server present.
10.10.10.10
Web Access Username admin
Web Access Password admin
Subnet Maska255.0.0.0
Default Gatewaya10.0.0.1
802.3af Compliant Ethernet Switch
Video Outdoor Intercom IP Phone IP PBX Server
*More installation and mounting
information is available in the
Operations Guide.
Accessory Kit
Mounting Component
(1) Assembly
(1) 1/2-inch EMT
compression
connector with extra
sealing locknut
(1) 531085* Hole
plug assembly
Optional Accessories
Optional Accessories
(for gooseneck mounting)
(4) Carriage bolts
(4) Carriage bolt nuts
(4) Carriage bolt washers (4) Security Torx Screws
Security Torx Key
Connecting the Intercom (Service Loop Routing)
Securing the Intercom
Contacting CyberData
Assembly
Faceplate
Faceplate
Mounting Screws
Flat Head Phillips or
Security Torx
Gang Box
Cable
Network
Service Loop
Ground Lug
Assembly
Faceplate
Faceplate
Mounting Screws
Flat Head Phillips or
Security Torx
Gang Box
Nut
Service Loop
Wire
Ground
Ground Cable Installation Network Cable Installation
Assembly
Faceplate
Faceplate
Mounting Screws
Flat Head Phillips or
Security Torx
Gang Box
Torx Key
GENERAL ALERT
Note: To mount the intercom, use methods
compliant with local electrical codes.
Caution
Equipment Hazard: Do not use an electric
or power screwdriver to fasten the faceplate
and PCB assembly to the gang box. To prevent
over-torque damage to the gasket, do not
apply more than 10 inch-pounds force.
Over-torquing will cause the gasket to tear,
Note: More installation and mounting
information is illustrated in the Operations
Guide.
risk moisture intrusion, and effectively voi
the manufacturer's warranty.
Sales: [phone] ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: [phone] ext. 136
RMA Email: [email protected]
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: [phone]
Fax: [phone]
http://www.cyberdata.net/
The IP Endpoint Company
Installation Quick Reference
SIP-enabled h.264 Video Outdoor Intercom
011410

© 2019, CyberData Corporation, ALL RIGHTS RESERVED 931332C Quick Reference Quick Reference 931332C © 2019, CyberData Corporation, ALL RIGHTS RESERVED
Terminal Block Connections
RTFM Button
5.118 [130.00] 2.252 [57.21]
5.118 [130.00]
5.198 [132.03] w/HOLE PLUG
DIMENSIONS ARE IN INCHES [MILLIMETER]
Call Button
Features Dimensions (Front and Side View)
Microphone
Hole
Camera
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Relay Common
4 = Relay Normally Open Contact
5 = Sense Input
6 = Sense Ground
7 = Remote Switch "A"
8 = Remote Switch "B"
*Contacts 1 and 2 on the terminal block are only for
powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
34
1
8
Wire (IN)
Tin Leads
Approx. 1/4” or
6mm
Terminal Block
can accept 16 AWG wire
Use a 3.17 mm (1/8-inch) flat blade
screwdriver for the terminal block screws
When the device is operational and linked to a network,
you can use the Reset Test Function Management
(RTFM) button (SW1 [see picture]) to announce the
device’s IP address or restore the device to the factory
default settings.
To announce the device’s current IP address:
• Press and release the RTFM button within a five
second window.
Note The device will use DHCP to obtain the new IP
address (DHCP-assigned address or default to
10.10.10.10 if a DHCP server is not present).
To restore the device to factory default settings:
• Press and hold the RTFM button for longer than five
seconds until you hear the device announce that it is
restoring the factory default settings.
RTFM button (SW1)
Dimensions (Rear View and Mounting Holes)
Side Conduit Mounting Restrictions
1.690
[85.85]
0.869 [22.07]
0.869 [22.07]
3.380 [85.85]
1.690
[42.93]
[42.93]
3.380
Dimensions are in Inches [Millimeter]
ø0.280 [ø7.11]
ø0.854 [ø21.69]
(4 Places)
Sealing Locknut
Compression
1/2" EMT
Connector
on This Side
Rubber Seal
Conduit
1/2" EMT
(Part of the
Locknut
Compression
Connector)
3
1
0.4 Inch [10mm]
Thread Depth Not to Exceed
Thread Depth
(Optional, 1 Provided)
Assembly
Hole Plug
Installation Steps:
1) Remove the hole plug assembly from the side of Backbox
then use it to cover the rear conduit hole.
2) Remove the locknut from the EMT compression connector, and
install the provided sealing locknut if the compression connector's
3) Insert the compression connector with the sealing locknut through
the side conduit hole, and then fasten the locknut inside the backbox.
thread depth exceeds 0.4 inch or 10 millimeters.
Make sure the threads do not protrude out more than 0.4 inch or 10 millimeters.
Backbox
2
4
1
4) Insert the EMT conduit into the EMT compression connector and then tighten.
*More installation and mounting information
is available in the Operations Guide.