CyberData 011211 series Manual

Quick Reference 931602A © 2019, CyberData Corporation, ALL RIGHTS RESERVED© 2019, CyberData Corporation, ALL RIGHTS RESERVED 931602A Quick Reference
Wall Mounting Options
Gang Box Mounting Options
Mounting Screw &
Wall Cutout
on Wall
Pre Drill Holes
to J1
Cable
Network
Backplate
Plastic Ribbed Anchor
Remove Screw & Nut
Before Install to Wall
Mounting
Screw (3x)
Loop Wire
Clockwise
Wire
Ground
Wire
Ground
Closed
Slots
Slots
Opening
Slot
Entry
Cable
Wall Cutout
or Two Gang Box
Backplate accept
Single Gang Box
Backplate
Wall Cutout
Wire
Ground
Two Gang Box use four
Single Gang Box use two
Screw Accessory Kit
In Two Gang Box Mounting
Move Ground Cable to Center Hole
Remove Screw & Nut
Before Install to Gang Box
Mounting
Screw (3x)
Loop Wire
Clockwise
Wire
Ground
Cable
Network
Closed
Slots
Cable
Slot
Entry
Cable
Getting Started
• Download the Operations Guide PDF file, from the Downloads tab at the following webpage:
https://www.cyberdata.net/products/011211
• Create a plan for the locations of your devices.
• WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
• WARNING: This enclosure is not rated for any AC voltages!
Parts
Contacting CyberData
Parameter Factory Default Setting
IP Addressing DHCP
IP Addressa10.10.10.10
Web Access Username admin
Web Access Password admin
Subnet Maska255.0.0.0
Default Gatewaya10.0.0.1
a. Default if there is not a DHCP server present.
(4) Plastic Ribbed Anchor (4) #6-32 FlatHead Countersunk
Machine Screw
(1) Wall Mounting Kit(1) Intercom Assembly (1) Gang Box Mounting Kit
(4) Sheet Metal Screw
Sales: [phone] ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: [phone] ext. 136
RMA Email: [email protected]
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: [phone]
Fax: [phone]
http://www.cyberdata.net/
The IP Endpoint Company
Installation Quick Reference
SIP Indoor Intercom
SIP Compliant
011211*, RAL 9003, Signal White
*Replaces the 011111 number.

© 2019, CyberData Corporation, ALL RIGHTS RESERVED 931602A Quick Reference Quick Reference 931602A © 2019, CyberData Corporation, ALL RIGHTS RESERVED
RTFM Button
Maximum Recommended Wall Cutout Dimensions
RTFM button (SW1)
When the device is operational and linked to a net-
work, you can use the Reset Test Function Man-
agement (RTFM) button (SW1 [see picture]) to
announce the device’s IP address or restore the
device to the factory
default settings.
To announce the device’s current IP address:
• Press and release the RTFM button within a
five second window.
Note The device will use DHCP to obtain the
new IP address (DHCP-assigned address
or default to 10.10.10.10 if a DHCP server
is not present).
To restore the device to factory default settings:
• Press and hold the RTFM button for longer
than five seconds until you hear the device
announce that it is restoring the factory default
settings.
DIMENSIONS ARE IN INCHES [MILLIMETER]
3.40 [86.4]
ø0.19 [ø4.8]
2.39 [60.8]
3.40 [86.4]
2.65 [67.3]
0.50 [12.8]
0.38 [9.5]
(4 Places)
Dimensions
Terminal Block Connections
4.53 [115.0]
4.53 [115.0]
DIMENSIONS ARE IN INCHES [MILLIMETER]
2.14 [54.3]
1
8
Wire (IN)
Tin Leads
Approx. 1/4” or
6mm
Terminal Block
can accept 16 AWG wire
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Relay Common
4 = Relay Normally Open Contact
5 = Sense Input
6 = Sense Ground
7 = Remote Switch "A"
8 = Remote Switch "B"
*Contacts 1 and 2 on the terminal block are only for
powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
34
Use a 3.17 mm (1/8-inch) flat blade
screwdriver for the terminal block screws