Cygnett EXOCHARGE WIRELESS DESK User manual

EXOCHARGE
WIRELESS DESK
USER MANUAL
Caution
1.
2. Do not expose to extreme weather conditions.
3. Do not place close to a magnetic strip or strip card
as it could cause magnetic failure.
4. Please keep charger a safe distance of at least 80cm
from any implantable medical devices to avoid medical
device interference.
5. This is not a toy and should be kept away from children.
6. In the case of the device overheating, please
disconnect immediately.
approved by the party responsible for compliance could
void the user’s authority to operate the equipment. Cygnett
takes no responsibility for damages caused by incorrect use
of its products. Made in China.
Cygnett Pty Ltd,
858 Lorimer St, Port Melbourne,
Victoria 3207 Australia
Cygnett UK Limited,
London, WC2H 9JQ
Cygnett USA Inc,
3838 W Carson St,
Ste 220, Torrance, CA 90503
Cygnett EU,
2718RD Zoetermeer, The Netherlands
Cygnett and the Cygnett logo are trademarks of Cygnett
Pty Ltd. Other brands and product names are trademarks or
registered trademarks of their respective holders.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
“NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
and on, the user is encouraged to try to connect the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit
-Consult the dealer or an experienced radio/TV
technician for help.”
This symbol on the product indicates that this product
shall not be treated as household waste. Instead it shall
be sent to the applicable collection point for the recycling
of electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health. For more information about the recycling of this
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
“FCC RF Radiation Exposure Statement Caution: To maintain
compliance with the FCC’s RF exposure guidelines, place the
product at least 20cm from nearby persons.”
Shielded cables must be used with this unit to ensure
compliance with the Class B FCC limits.

Installation Instructions
1. Using the cable provided, insert the Micro-USB end into
the Micro-USB input (B) of the wireless charger, and the
2. Place your wireless charging device on the wireless
chargingoutput (B), making sure that it is positioned
in the centre ofthe wireless charging disc.
Troubleshooting
To achieve fast charging, please ensure you are using a
charger that is capable of supporting QC 3.0 charging
protocol. For optimum charge speed, adjust your device
so that it is aligned to the centre of the wireless charging
output (B). Please ensure that the case on your phone
checking the performance. Some cases interfere with
wireless charging if they contain metallic material or are
overly thick.
Name ExoCharge
Wireless Desk
Item Number CY3450PPWIR
Input 5.0V⎓2.0A (10.0W)
9.0V⎓2.0A (18.0W)
5.0W
Wireless Output 7.5W
10.0W
Total Output 10.0W Max
FCC ID 2AEDZCY3450PPWIR
A Wireless Charging Output
B Micro-USB Input
B
A