Cygnus EL-180B User manual

1. Door Types: Wooden door, Glass door, Metal door, Fireproof door.
2. Control Mode: Building intercom system, Access control system.
1. Using powerful power supply, output voltage should be DC12V±10%,cable ＞0.75mm.
2. Don' hurt the galvanization layer during the installation.
3. Ensure the mounting plate well attach to the lock body.
4. The rubber ring must be added between armature plate and door leaf, don't fasten the screw tightly, keep the rubber ring elastic.
5. Don't welded the mounting plate to the door, or will effect the lock.
6. Clean the slushing oil with cloth, don't use alkaline or pungent cleaner.
1. Specification
2. Application Range
3. Note
Read the manual before usage and keep for future reference.
Electromagnetic Lock
User Manual
12/24VDC
12/24VDC
12/24VDC
12V/300mA*2
24V/150mA*2
12V/300mA
24V/150mA
170L*42W*21H 12/24VDC 12V/300mA
24V/150mA 180kg(350Lbs)
-180A
-180B
-180AS
-180BS
No
Yes
340L*42W*21H 180kg*2(350Lbs*2)
No
No
No
No
170L*42W*21H
340L*42W*21H 12V/300mA*2
24V/150mA*2
180kg(350Lbs)
180kg*2(350Lbs*2)
No
Yes
Double Door
Double Door
Red
Blue
Black
White
DC12V
POWER
+
-
DC12V:Connect Red and Blue wire as Positive pole of
Connect White and Black wire as Negative pole of “-”
“+”,
4. Wiring of Lock (W )ithout signal output
Red
Blue
Black
White
DC12V
POWER
+
-
NO
COM
White
White
5. Wiring of Lock ( )with signal output
DC12V:Connect Red and Blue wire as Positive pole of
Connect White and Black wire as Negative pole of “-”
“+”,
Red
Blue
Black
White
DC24V
POWER
+
-
NO
COM
White
White
DC24V: Red wire is Positive pole of
pole of “-”and connect White and Blue wire.
“+”, black wire is Negative
Red
Blue
Black
White
DC24V
POWER
+
-
DC24V: Red wire is Positive pole of
pole of “-”and connect White and Blue wire.
“+”, black wire is Negative
EL
EL
EL
EL
EL-180

1．Use the supplied template to determine the correct location and size of mounting holes for both the door and frame header. Ensure that
the door opens away from the Maglock. In the case of a single door, the Maglock is positioned as close as possible to the vertical section
of the door jamb.Drill door and frame as indicated.
2．Loosely install the mounting plate using two of the supplied Philips head mounting screws in the elongated slots. Attach the Maglock to
the mounting plate.
3．Using a hammer, lightly tap both roll pins into the armature plate until they are secure.
4．Before installing the Hexnut, the hole in the door may need to be drilled or tapped. Refer to page 2 for this information. Using the componets
shown in the image to the right, mount the armature to the door. Make sure that the armature plate is not over tightened and that it is installed
as shown in the following diagram. The armature plate must be free to self align with the door.
5．Ensure the armature and magnet are aligned. Adjust the mounting plate to suit and then drill the appropriate sized holes in the door
header for the remaining attachment screws.
6. Close the door to test holding force. The angle between armature plate and magnetic lock can be adjusted by adding or reducing washers.
6. Disassemble Procedure
7. Standard Mounting Method
6
1 2 3
45
8. Bracket Mounting Method
For in-swing door, install the lock body inside
and then need to install the ZL bracket at the
same time.
Magnetic locks installed in glass doors
require extra U bracket (for 10-15mm
glass door thick).
Wh e n the d o o r width i s less t h a n 42mm
the width is not enough for Armature Plate
of the magnetic lock installed, it need to
add the additional L type bracket.
Outdoor
Door Leaf
Door