CYP CDPS-CS6 User manual

Operation Manual
Operation Manual
Control System Center
CDPS-CS6

DISCLAIMERS
The information in this manual has been carefully checked and is believed
to be accurate. Cypress Technology assumes no responsibility for any
infringements of patents or other rights of third parties which may result from
its use.
Cypress Technology assumes no responsibility for any inaccuracies that
may be contained in this document. Cypress also makes no commitment to
update or to keep current the information contained in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express written
permission and consent from Cypress Technology.
© Copyright 2018 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document are trademarks of
the companies with which they are associated.

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply. Please keep the
following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain, moisture
or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings
or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it
is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to
be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings
in the unit housing that provide ventilation and allow for su󰀩cient space
for air to circulate around the unit.
• Please completely disconnect the power when the unit is not in use to
avoid wasting electricity.
VERSION HISTORY
REV. DATE SUMMARY OF CHANGE
RDV1 2016/01/07 Preliminary release
RDV2 2016/04/21 Add WebGUI
RDV3 2016/06/14 Revised trigger event number to 8
VS0 2017/02/21 Updated text/diagrams
VS1 2019/10/04 Added scheduling and additional macro support
VS2 2020/07/29 Full update to revised manual format

CONTENTS
1. Introduction...................................................... 1
2. Applications ..................................................... 1
3. Package Contents ........................................... 1
4. System Requirements..................................... 2
5. Features............................................................ 2
6. Operation Controls and Functions ................ 3
6.1 Front Panel.................................................. 3
6.2 Left Side Panel ............................................ 3
6.2 Rear Panel................................................... 4
6.4 IR Cable Pinouts.......................................... 5
6.5 RS-232/422/485 Pinouts ............................. 5
6.6 WebGUI Control .......................................... 6
6.6.1 Macro Settings Tab............................. 8
6.6.2 Extension Macro Tabs 1~3............... 10
6.6.3 Command Settings Tab .................... 11
6.6.4 Schedule Settings Tab...................... 13
6.6.5 Network Settings Tab ....................... 15
6.6.6 System Settings Tab......................... 16
6.6.7 Time Settings Tab............................. 17
6.7 Telnet Control ............................................ 18
6.8 Telnet Commands...................................... 18
7. Connection Diagram ..................................... 22
8. Specications ................................................ 23
8.1 Technical Specications ............................ 23
9. Acronyms ....................................................... 24

1
1. INTRODUCTION
This Control System Center is ideal for a user who has a wide variety of
devices that need to be controlled. It comes with eight external trigger
connections which directly activate 8 (of 32 total) user dened macro events
stored within the unit. All 32 macros are available to be activated via the
WebGUI, or by Telnet. Those user dened macros can send control signals
to remote devices via Ethernet, IR, relay, or serial port (RS-232/422/485)
allowing for the control of a large array of devices at the push of a button.
A battery backed-up clock allows for detailed event scheduling based on a
repeating daily/weekly schedule, or single events.
An integrated IR code learning function is also available, allowing the user to
store and re-transmit the IR codes sent by nearly any standard IR remote. A
number of user control interfaces are available including WebGUI and Telnet.
Last but not least, this unit supports PoE (Power over Ethernet) allowing it to
be powered directly from a standard PoE network switch, without the need
for an external power adapter, allowing for incredible installation exibility.
2. APPLICATIONS
• 1× Control System Center
• 1× 5V/2.6A DC Power Adapter
• 1× IR Learner/Extender Cable
• 4× IR Blaster Cable
• 7× Terminal Block Connectors
• 1× Operation Manual
3. PACKAGE CONTENTS
• 1× UHD+HDMI/DP over Fiber Transceiver
• 1× 12V/3A DC Power Adapter
• 1× Power Cord
• 1× 3-pin Terminal Block
• 1× Shockproof Feet (Set of 4)
• 1× Operation Manual

2
4. SYSTEM REQUIREMENTS
• Equipment which can be controlled via Telnet, serial, IR remote or relay.
• An active internet connection from a switch or router for control of Ethernet
devices.
5. FEATURES
• 8 trigger inputs linked directly to 8 user macros allowing for instant control
activation
• 24 additional macros that can be activated via Ethernet, or on a schedule.
• 4 relay bypasses to control devices such as projector screens, lighting,
etc.
• 4 IR outputs to control devices such as TVs, media players, etc.
• Integrated IR code learning functionality
• Battery backed up clock for scheduling events
• Multiple user control interfaces including WebGUI, Telnet and RS-232 /
422/485
• Simple conguration of macros, triggers and relay settings via the WebGUI
• PoE (Power over Ethernet) support
• Firmware can easily be updated in the eld via USB

3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
1234
RELAY CONTROL OUT
1234
INFRARED OUT
IR IN
IR OUT
OUT
IN
GNDGND
321
GND
3.3V
12
3
1 2
1RELAY CONTROL OUT Ports 1~4: Connect to devices that support
relayed power (0~30VDC/10A or 0~250VAC/10A) activation to control
them via macro commands.
2INFRARED OUT Ports 1~4: Connect to the provided IR Blaster to
transmit IR signals to devices within direct line-of-sight of the IR Blaster.
6.2 Left Side Panel
1
1IP RESET Pinhole: Use a paperclip to press and hold this recessed
button for 10 seconds to reset the IP conguration to the factory defaults.
Note: The unit’s default IP address is 192.168.1.50.

4
6.2 Rear Panel
IR IN
TRIGGER IN
COMPORT
SERVICE
CONTROL
(POE)
POWER
DC 5V
1 5V 234
5
GND 678
54321
RXD
RS232
RS422
RS485
TXD GND
RX+ RX- TD-TD+ GND
TD-TD+ GND
21 3 4 5 6
1DC 5V Port: Plug the 5V DC power adapter into the unit and connect it
to an AC wall outlet for power. (Optional)
Note: Not required if the unit is being powered via PoE.
2CONTROL (PoE) Port: Connect directly, or through a network switch, to
your PC/laptop to control the unit via Telnet/WebGUI.
Note: If the unit is connected to a network switch that provides PoE then
no power adapter is required to power the unit.
3SERVICE Port: This slot is reserved for rmware update use only.
4COMPORT Terminal Block: Connect to the device you wish to control
via a 3(or 5)-pin adapter cable to send RS-232/422/485 commands from
the unit. Baud rates up to 115200 are supported. For pin connection
details please refer to the diagram above.
5TRIGGER IN Terminal Block: Connect to any device with trigger or
switch functionality such as window security alarms, motion detectors,
door switches, etc. Each of the 8 trigger inputs will activate the
associated macro when triggered. A minimum of 5V DC is required to
activate the trigger. For pin connection details please refer to the diagram
above.
6IR IN Port: Connect to the provided IR Extender to allow IR control of the
unit or for learning IR commands. Ensure that the remote being used is
within direct line-of-sight of the IR Extender.
Note: For additional IR learning details please refer to section 6.6.3.

5
6.4 IR Cable Pinouts
IR Blaster
Cabl
e
1
2
3
Infrared
Power
Not Use
d
IR Extender
Cabl
e
1
2
3
Infrared
Power
Ground
6.5 RS-232/422/485 Pinouts
RS-232 RS-422
1
2
3
4
5RxD
TxD
GN
D
N/A
N/A
5-pin
Terminal Block
1
2
3
4
5Rx+
TD-
GN
D
Rx-
TD+
5-pin
Terminal Block
RS-485
1
2
3
4
5N/A
TD-
GN
D
N/A
TD+
5-pin
Terminal Block

6
6.6 WEBGUI CONTROL
• Device Discovery
Please obtain the “Device Discovery” software from your authorized dealer
and save it in a directory where you can easily nd it.
Connect the unit and your PC/Laptop to the same active network and
execute the “Device Discovery” software. Click on “Find Devices on Internet”
and a list of devices connected to the local network will show up indicating
their current IP address.
Note: The unit’s default IP address is 192.168.1.50.
By clicking on one of the listed devices you will be presented with the
network details of that particular device.
1) IP Mode: If you choose, you can alter the static IP network settings for
the device, or switch the unit into DHCP mode to automatically obtain
proper network settings from a local DHCP server. To switch to DHCP
mode, please select DHCP from the IP mode drop-down, then click “Save”
followed by “Reboot”.
2) WebGUI Hotkey: Once you are satised with the network settings, you
may use them to connect via Telnet or WebGUI. The network information
window provides a convenient link to launch the WebGUI directly.

7
• WebGUI Overview
After connecting to the WebGUI’s address in a web browser, the login screen
will appear. Please enter the appropriate user name and password then click
“Submit” to log in.
Note: The default user name and password is “admin”.
On the left side of the browser you will see the following menu tabs where
all primary functions of the unit are controllable via the built in WebGUI. The
individual functions will be introduced in the following sections.

8
6.6.1 Macro Settings Tab
Click on the “Macro Settings” tab to execute or edit the settings for the
primary macro buttons. These macros can be executed by activating the 8
input triggers on the unit as well as via the WebGUI or Telnet.
1) Macros 1~8: These align with Trigger Inputs 1~8. When a trigger is
activated the unit will execute the associated macro command.
By default, the unit comes with multiple macros pre-congured for testing
the unit’s functionality. These presets are:
Macro 1: Sequentially close Relays 1 through 4 with a 100ms delay.
Macro 2: Sequentially open Relays 1 through 4 with a 100ms delay.
Macro 3: Sequentially toggle the state of Relays 1 through 4 with a
100ms delay.
Macro 4: Sequentially send IR signals from emitters 1 through 4 with
a 100ms delay.
Macros 5~8: Send a sample text string over the COM port with a
100ms delay afterwards.
Click on the macro buttons to demonstrate and test the various functions.
2) Macro Edit: Clicking on the edit icon ( ) in any macro button will open
up the Macro Edit window. After all desired changes to the macro have
been made, click on the “Save Change” button to commit the changes to
memory.

9
Edit Name: At the top of the Macro Edit window is a text eld where
you can edit the name of the macro. Type your new macro name into
the box and then click the save icon ( ) to save it.
Insert Command: Clicking on the insert command icon ( ) will add a
new command before the current one. The “Command Select” window
will open where you can select one of the pre-dened commands from
the list. After selecting a command the “Set Destination” window will
open to allow the selection of the delay and target interface for the
command.
  Note:Conguringpre-denedcommandsiscoveredinsection6.6.3.
Reorder Commands: Within the Macro Edit window the up/down
arrows will move the current command’s position and change the
command execution order.
Set Destination: Clicking on the destination edit icon ( ) allows you
to edit the delay and target interface for the command.
-Delay(ms): This setting is the length of time to wait before sending
the next command and is set in milliseconds.
-Interface: The interface for sending commands can be set to the
unit itself (SysCMD), to a specied IP address (TELNET), to a
specied RS-232 port (COM), to a specied IR port (IR) or to trigger
a relay port (Relay). Sending commands to devices on the local
network, or across the internet requires entering the IP address
and network port of the destination device. Once the destination
information is complete please click on the “Save Change” button.
Note: It is strongly suggested to not set a delay time less than
100msforsystem,RS-232,IR,andrelaycommandsorlessthan

10
500ms for Telnet commands to ensure that the command is properly
received and executed before the next command is sent.
Delete Command: Clicking on the delete command icon ( ) will
delete the command.
Add Command: To add a new command to the end of the execution
list, click on the “Add” button. The “Command Select” window will open
where you can select one of the pre-dened commands from the list.
After selecting a command the “Set Destination” window will open to
allow the selection of the delay and target interface for the command.
6.6.2 Extension Macro Tabs 1~3
Click on any of the three “Extension Macro” tabs to execute/edit the 24
additional software-only macro buttons. These macros can only be activated
via the WebGUI or Telnet. Extension Macro editing is identical to editing
macros 1 through 8, please refer to section 6.6.1 for more details.

11
6.6.3 Command Settings Tab
The “Command Settings” tab provides a way to create, edit or delete the
commands used by macros. Each command is composed of standard ASCII
or HEX data and represents either a system command, relay command, IR
code, or telnet/serial port command.
Note: The number of commands that can be stored in the unit is limited
by memory and it is generally recommended that commands be under
128 characters long (including spaces). However, if longer commands are
needed there is limited support for commands up to 512 characters long. In
this case the number of (up to) 512 character commands is limited to 32 and
the remaining 96 commands must be under 128 characters.
1) Edit Command: Clicking on the “Edit” button will open up the “Command
Edit” window which provides a way to dene the contents of each
individual command. Once all changes are satisfactory, click on the “Save
Change” button to save them into the unit.
Command Label: Assign a name for the command by entering the
text into this eld. All commands must have a label.

12
IR Learn: To learn an IR command, rst make sure the included
IR Receiver is connected to the unit’s IR IN port, then press the “IR
Learn” button. After doing this a notice will appear in the WebGUI
to send the IR signal within 5 seconds. Point the remote control at
the IR receiver and press the button that contains the command you
wish to learn. A command string will appear in the text entry window
containing the information captured from the IR remote.
Command Data: The command data to send is entered in this text
box. The types of commands available and the interface to use with
them are detailed below.
 Note: Except where explicitly mentioned, the “CYP” format checkbox
should always be checked.
System Commands (SysCMD Interface): Commands to control
functions of the unit directly using the Telnet functions detailed in
section 6.8.
 Note: Care must be taken when sending system commands, as they
can impact the functionality of the unit itself.
Telnet or Serial Commands (Telnet & COM Interfaces): Simply
enter the plain ASCII text of the command in the space provided.
Hex codes should be entered using the format: \xHH where “HH” is
replaced by an octet pair. For example a standard carriage return
would be entered as: \x0D.
IR Commands (IR Interface): Typically this data is automatically lled
in by using the IR Learning function, however an IR code may also be
manually entered if necessary.
 Note: If the IR code is in “Pronto” format the “RAW HEX” checkbox
must be checked.
Relay Commands (Relay Interface): Commands to control the state
of each relay port. The port to control is assigned during the creation
of each individual macro.
-CLOSE: Closes the assigned relay port.
-OPEN: Opens the assigned relay port.
-TOGGLE: Toggles the state of the assigned relay port.
2) Delete Command: To clear the contents of a command, click on the
“Remove” button. The contents will be removed immediately.
Note: There is no “Undo” function! Please use caution when using the
“Remove” button!

13
6.6.4 Schedule Settings Tab
The “Schedule Settings” tab provides multiple ways to automate and
schedule the execution of any of the macros dened in this unit. Scheduled
events can be individually disabled without deleting the event from the
master list.
1) Event Scheduling: Events can be scheduled to automatically activate at
a single set time, or on a repeating schedule.
Note: Each scheduled item must be set as “Active” for it to activate at the
scheduled time.
Repeat: Items in this section will execute at their set times on the
selected days (Sunday through Saturday) every week as long as they
are marked as “Active”.
Once: Items in this section are scheduled to occur a single time at the
specied time and date. Each item will automatically change to “None
Active” after they have been executed once.
2) Schedule Edit: To edit an existing scheduled event, or congure a new
one, click on the “Edit” button. To delete a scheduled event, click on the
“Remove” button.
 Note:TheavailableoptionsareslightlydierentbetweenRepeatand
Once events.

14
Active: Click this to toggle if the scheduled event is enabled or
disabled.
Weekly (Repeat Schedule Only): When editing a repeating event
schedule, click the checkboxes next to the days of the week for the
event to occur on.
Date & Time: Click within the Time/date box to open up the time/date
selection window. Use the available controls to set the activation time
(and date, if applicable) for the current event schedule.
Macro/Extension Macro: Click on this button to open a window
displaying all currently dened macros. Select the macro to be
executed by the currently selected event schedule.

15
6.6.5 Network Settings Tab
Click on the “Network Settings” tab to change the network settings for the
unit. You can manually set the IP address, netmask and gateway address in
“Static IP” mode, or you can obtain an IP address automatically by enabling
DHCP.
1) Network Settings: IP mode may be switched between Static IP or
DHCP. In Static IP mode the IP, netmask and gateway addresses may
be manually set. When in DHCP mode, the unit will attempt to connect
to a local DHCP server and obtain IP, netmask and gateway addresses
automatically. Please press “Save” after making any changes to the IP
conguration or mode. To return all network settings to their defaults,
press the “Network Reset” button.
Note: If the IP address is changed then the IP address required for
WebGUI/Telnet access will also change accordingly.