CYP DS-MSC User manual

DS-MSC
Digital Signage Multi-Screen
Video Wall Controller
OPERATION MANUAL

Safety Precautions
Please read all instructions before attempting to unpack or install or
operate this equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
 Always follow basic safety precautions to reduce the risk of
re, electrical shock and injury to persons.
 To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
 Never spill liquid of any kind on or into this product.
 Never push an object of any kind into this product through
module openings or empty slots, as you may damage parts.
 Do not attach the power supply cabling to building surfaces.
 Do not allow anything to rest on the power cabling or allow it to
be abused by persons walking on it.
 To protect the equipment from overheating, do not block the
slots and openings in the module housing that provide
ventilation.
Revision History
Version No Date Summary of Change
RDV01 20110119 Preliminary Release
RDV02 20110317 Add New OSD Menu
RDV03 20110324 Change OSD Figures
RDV04 20110719 Add TV Option

Table of Contents
1
1
1
1
2
3
4
4
4
5
6
7
7
7
8
9
1. Introduction ……………………..……………………...…........….…….
2. Applications …………………..………………….……...................…..
3. Package Contents ………………………...........……….................…
4. System Requirements ……………..……….........………............…….
5. Features …………………………………………......……........…...……
6. Specications ………………………………...……..........………....….
7. Operation Controls and Functions ……………...……..............……
7.1 Front Panel ..............................................................................
7.2 Rear Panel .…………………………………..…….......…...….…
7.3 OSD Menu .…………………………………..…….......…...….…
8. Remote Control .......................…......……………..........…..…....…...
9. RS-232 Protocol ................................................................................
9.1 Pin Denition .............................................................................
9.2 Command ...............................................................................
10. Connection and Installation ….………………….........…..…..…......
11. Acronyms …......................................................................................

1. Introduction
To capture the public’s attention, the Multi-Screen Video Wall control system
is ideal for advertising, entertaining and displaying information. The device
allows users to display HDMI or PC sources to multiple LCD monitors, while
thanks to the built-in RS-232 you are able to fully customize the LCD panels
giving you complete control over 2x2, 3x3, 4x4 and 5x5 video walls. This
device is also embedded with a PC to HDMI scaler, which allows the input
PC video signal to be integrated and converted to digital HDMI signal output
to the video wall. There is a pair of additional L/R RCA connecters for user to
output analog audio (extracted from the HDMI source, or routed from the
analog audio input) to local speakers. Further, the IR remote and the RS-232
control free users with on hand control from anywhere they wish.
2. Applications

TV wall

Video wall

Display wall

Gaming wall

Movie wall

Combination advertising wall
3. Package Contents

Video wall control system(s)

5V DC power adaptor(s)

Operation Manual
4. System Requirements
HDMI or PC splitter/matrix with input source signal and connection cables,
display TV/monitor with connection cables.
1

5. Features

Supports 6 or more video wall combinations of HxV: 2x2(four monitors),
3x2(sis monitors), 3x3(nine monitors), 4x3(12 monitors),4x4(16 monitors)
and 5x5 (25 monitors)

Supports both HDMI and PC (with audio) input sources

Resolution support up to 1080p full HD

Use RS-232 cables to cascade over every connected CVW-11HS boxes to
remotely control each monitors with one setting only.

Supports external IR receiver for IR remote control
Note: Requires HDMI or PC (with audio) signal splitter to distribute vide /
audio signal to each connected CVW-11HS box.
2

6. Specications
Input Ports 1xHDMI, 1xPC, 1xRS-232 (female jack), 1xIR,
1xL/R (3.5Ø phone jack)
Output Ports 1xHDMI, 1xRS-232 (male jack), 1xL/R (RCA jack)
IR Frequency 38Hz
IR Cable Length 3M
Input Resolution Supports PC: VGA ~ SXGA
HDMI: 48op~1080p
Output Resolution HDMI: 720p & 1080p
Supports
Audio Format PCM 2Ch
Power Supply 5V/3.6A DC (US/EU standards, CE/FCC/UL Certied)
ESD Protection Human body model: ± 8kV (air-gap discharge)
± 4kV (contact discharge)
Dimension (mm) 200 (W) x 155 (D) x 45(H)
Weight (g) 815
Chassis Material Aluminum
Silkscreen Color Black
Operating Temperature 0˚C ~ 40˚C / 32˚F ~ 104˚F
Storage Temperature -20˚C ~ 60˚C / -4˚F ~ 140˚F
Relative Humidity 20 ~ 90% RH (Non-condensing)
Power Consumption (W) 15.5
3

7. Operation Controls and Functions
7.1 Front Panel
① ② ③ ④ ⑤ ⑥
HDMI IN AUDIO IN PC IN RS 232 IN RS 232 OUT IR IN
DS-MSC Video Wall Controller
①HDMI IN: This slot is to connect from HDMI splitter or matrix with input
source signal.
②Audio IN: This slot is to connect with the audio signal from the source
equipment with 3.5Ø phone jack.
③PC IN: This slot is to connect from PC/RGB splitter or matrix with input
source signal.
④RS-232 IN: As a first device of the video wall system, this slot is to connect
with PC/NB equipment for RS-232 control. Starting from the second device
of the video wall system this slot should be connect from the RS-232 out of
the last device.
Note: For RS-232 control it required a special level-shift board and it is an
optional accessory selection.
⑤RS-232 OUT: This slot is to connect to the next video wall control system’s
RS-232 IN.
⑥IR IN: This slot is to connect with IR blaster included in the package for
receiving the IR signal of the device’remote controller.
7.2 Rear Panel
② ③①
HDMI OUT
DC 5V
AUDIO OUT
L
R
①DC 5V: Connect this slot with power adaptor included in the package
from the AC wall outlet. When the power is plugged on the device will
automatically power ON.
②Audio OUT L/F: These slots are to connect with RCA jack cables to the
active speaker or to display’s audio input.
③HDMI OUT: This slot is to connect to the display with HDMI input.
4

7.3 OSD Menu
MAIN MENU
PICTURE
MENU*1
STANDARD ON/OFF
R OFFSET 0~255 (118)
G OFFSET 0~255 (116)
B OFFSET 0~255 (118)
R GAIN 0~255 (098)
G GAIN 0~255 (098)
B GAIN 0~255 (098)
CONTRAST 0~63 (50)
BRIGHTNESS 0~63 (40)
SETUP MENU*1
LANGUAGE ENG / T.CHINESE (ENG)
HDMI SOUND ON/OFF (ON)
STANDARD ON/OFF (OFF)
H POSITION START 000~385 (*2)
V POSITION START 000~53 (*2)
H ZOOM SIZE 000~255 (0)
V ZOOM SIZE 000~255 (0)
TV Option Width 1~10 (1)
TV Option Height 1~10 (1)
*NOTE: 1. The Picture Menu allows users to adjust single monitor’s setting while
the Setup Menu will only needs to be adjust once and all monitors
will be automatically adjusted.
2. Defual value will adjusted automatically depending the the input
signal's timing.
Picture Standard: Set it to ON will allow system to set the picture menu
into the default value as indicated in the ( ).
Picture R/G/B Offset: These functions are to set the single picture's R/G/B
brightness.
Picture R/G/B Gain: These functions are to increase or decrease the color of
single picture's R/G/B.
Picture Contrast: This function is to set the single picture's color contrast.
Picture Brightness: This function is to set the single picutre's brightness.
Setup Language: There are two language available in the OSD and they are
English and Traditional Chinese.
Setup HDMI Sound: This function is to set the HDMI output audio sound to be
ON or OFF.
Setup Standard: Set it to ON will allow system to set the setup menu into the
default value as indicated in the ( ).
5

Setup H/V Position Start: These functions are to set the total value of the
vertical and horizontal value of the TV wall.
Setup H/V Zoom Size: These functions are to set the total value of the vertical
and horizontal zoom in and zoom out size of the TV wall.
Setup H/V Blanking Edit: These functions are to set the total value of the
vertical and horizontal value of the blanking area of
the TV wall.
Setup TV Option Width: This function is to set the numbers of the TV/display
that is to be on a horizontal line of the TV wall.
Setup TV Option Height: This function is to set the numbers of the TV/display
that is to be on a vertical line of the TV wall.

8. Remote Control
① Power: Press this button to switch on the
device(s). All the connected Video wall system
control device(s) will be switch to ON.
② Power OFF: Press this button to switch off the
device. All the connected Video wall system
control device(s) will be switch to OFF.
③ SINGLE: Press this button to set the image
to be displayed on each and every connected
TV/monitor identically.
④ FULL: There are 6 options of setting an image
to be displayed on TV/ monitor and they are
2x2, 3x3, 4x4, 3x2, 4x3 and 5x5.
⑤ pqtu&OK: Press the arrow buttons to select
and adjust the selection in the OSD menu and
value or to select the display. Press OK to
confirm the selection.
⑥ MENU: Press this button to enter into the OSD
menu. When the setting is selected and
confirmed all the output display will
automatically changed to the selected settings.
⑦ RETURN: Press this button to return to the last
layer of OSD selection or to exit the OSD.
⑧ HDMI: Press this hot key to select the input source
from HDMI IN.
⑨ VGA: Press this hot key to select the input source
from PC IN.
⑩ U/OVER: Press this key to adjust the screen when the image is overscan or
underscan.
⑪ 720P: Press this hot key to switch the output timing to 720p
⑫ OPTION: Press this key to switch to the special setting of the display image
set by the factory design.
⑬ 1080P: Press this hot key to switch the output timing to 1080p
*Function that automatically adjust all monitors in once.
POWER
2X2 3X3
3X2 4x3 5x5
RETURN MENU
HDMI VGA U/OVER
720P OPTION 1080P
POWER OFF
CR-98
FULL
OK
4X4
SINGLE
②
⑥
⑩
⑬
①
③
④
⑤
⑦
⑧
⑪
⑨
⑫
6

9. RS-232 Protocol
9.1 Pin Denition
RS-232 IN RS-232 OUT
Pin 1 NC Pin 1 NC
Pin 2 TxD Pin 2 RxD
Pin 3 RxD Pin 3 TxD
Pin 4 NC Pin 4 NC
Pin 5 GND Pin 5 GND
Pin 6 NC Pin 6 NC
Pin 7 Connect to Pin 8 Pin 7 Connect to Pin 8
Pin 8 Connect to Pin 7 Pin 8 Connect to Pin 7
Pin 9 NC Pin 9 NC
Baud Rate: 19200bps
Data bit: 8 bits
Parity: None
Stop Bit: 1 bit
Flow Control: None
9.2 Command
COMMAND ACTION
0x23 0x53 0x30 0x30 0x31 0x23 POWER ON
0x23 0x53 0x30 0x30 0x30 0x23 POWER OFF
0x23 0x43 0x30 0x30 0x30 0x23 UNDER SCAN
0x23 0x43 0x30 0x30 0x31 0x23 OVER SCAN
0x23 0x43 0x52 0x11 0x00 0x23 SINGLE
0x23 0x43 0x52 0x11 0x00 0x23 2x2
0x23 0x43 0x52 0x11 0x00 0x23 3x3
0x23 0x43 0x52 0x11 0x00 0x23 4x4
0x23 0x43 0x52 0x11 0x00 0x23 5x5
0x23 0x43 0x52 0x11 0x00 0x23 3x2
0x23 0x43 0x52 0x11 0x00 0x23 4x3
0xEF 0x05 0xD7 0xC0 0x22 0x07 0xEE Change to HDMI
0xEF 0x05 0xD0 0xC0 0x22 0x00 0xEE Change to PC
0xEF 0x06 0x8A 0xC0 0x20 0x01 0xBB 0xEE Option
7