CYP SDV-CS8 User manual

OPERATION MANUAL
SDV-CS8
SDV System Controller & Configurator

3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer file, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2019 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 26/07/2019 First release (RDV1)

5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................7
4. System Requirements ...........................7
5. Features..................................................7
6. Operation Controls and Functions.......8
6.1 Front Panel................................................... 8
6.2 Rear Panel..................................................... 8
6.3 Remote Control.......................................... 9
6.4 IR Cable Pinout .........................................10
6.5 RS-232 Pinout and Defaults.................10
6.6 WebGUI Control .......................................11
6.7 Telnet Control............................................35
6.8 RS-232 and Telnet Commands............36
7. Connection Diagram .......................... 43
8. Specifications...................................... 44
8.1 Technical Specifications ........................44
9. Acronyms............................................. 45

6
1. INTRODUCTION
This IP Master Controller is a powerful and exible solution for controlling
multiple SDVoE (Software Dened Video over Ethernet) based extenders
within same network. The user only needs to install this unit into the same
local network as the extenders (Transmitter and Receiver) to easily dene
and congure channel routing selections (including video, audio, and a
variety of control interface types) using the WebGUI. Without the use of
this centralised control unit, each Transmitter and Receiver pair would
only be able to function in a point-to-point capacity.
Additionally, this unit supports controlling and conguring the matrix,
video wall, and MultiViewer modes of connected SDVoE units. The
settings of all connected Transmitter/Receiver units, including IP address,
netmask and extender status are clearly displayed within the WebGUI.
A trigger input interface is also provided to allow the easy addition of a
remote control keypad, or other trigger-supporting products, which can
be installed within a podium or within a table in a conference room or
classroom. This interface can allow the user to activate stored presets with
the simple press of a button. Standard control is available via WebGUI
(remote or local), RS-232, Telnet and IR Remote.
2. APPLICATIONS
Video/TV wall display and control
Security surveillance and control
Commercial advertising, display and control
Home Cinema with Smart Home Controls
Retail sales and demonstration

7
3. PACKAGE CONTENTS
1× IP Master Controller (SDVoE)
1× 5V/2.5A DC Power Adapter
1× Terminal Block (3-pin)
3× Terminal Block (5-pin)
1× IR Extender Cable
1× Remote Control (CR-183)
1× Shockproof Feet (Set of 4)
1× Operation Manual
4. SYSTEM REQUIREMENTS
An active network connection from a switch or router for control of
compatible Video over IP devices.
5. FEATURES
Enables the management and conguration of multiple compatible
SDVoE (Software Dened Video over Ethernet) extenders through a
single WebGUI
Provides control over the independent routing of video, audio and
control signals between all local compatible transmitters and receivers
Control over matrix, video wall, and MultiViewer modes using WebGUI
presets
WebGUI clearly displays the status of all connected Transmitters and
Receivers, including IP address, channel selection, etc.
Can generate serial commands to directly control an external serial-
controllable device
Can be powered by Ethernet switches supporting the IEEE 802.3af
2003 PoE standard (Optional)
Trigger Control Keypad support for easy, single-button, preset
activation (Optional, coming in the“Phase 2”update)
Standard control is available via WebGUI (remote or local), RS-232,
Telnet, and IR Remote

8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER IR
IP Master Control SDV-CS8
1 2
1POWER LED: This LED will illuminate to indicate the unit is on and
receiving power.
2IR Window: Accepts IR signals from the included IR remote for control
of this unit only.
6.2 Rear Panel
LAN 1(POE)LAN 2USBHDMI OUTRS-232CONTROLIR EXT DC 5V TRIGGER IN
TX RX
1 2 3 4 5 6 7 8 109
1IR EXT Port: Connect to the provided IR Extender to extend the IR
control range of the unit. Ensure that the remote being used is within
direct line-of-sight of the IR Extender.
2CONTROL Terminal Block: Connect to a serial controllable device for
the transmission of RS-232 signals.
3RS-232 Terminal Block: Connect to a PC, laptop or other serial control
device with a 3-pin adapter cable to control the unit via RS-232.
4TRIGGER IN Terminal Block: This functionality is not currently
available and will be added in the“Phase 2” update.
5HDMI OUT Port: This functionality is not currently available and will
be added in the “Phase 2” update.
6USB Port: This functionality is not currently available and will be
added in the “Phase 2” update.
7LAN 2 Port: Connect directly, or through a network switch, to your
PC/ laptop to control the unit via WebGUI/Telnet.

9
8LAN 1(POE) Port: This port is used to connect to the SDVoE devices
to be controlled. Connect to the SDVoE units’private network through
their dedicated network switch, to enable detection and control over
those units.
Note: If the connected network switch supports the IEEE 802.3af 2003
PoE (Power over Ethernet) standard, this unit can optionally be powered
directly via this Ethernet port.
9FACTORY RESET Pinhole: Press and hold for 3 seconds to reset the
unit to its factory defaults, including Ethernet settings.
Note: While the reset is in process, the LEDs on the front of the unit will
ash. Once the reset is complete, the unit will return to normal operation.
10 DC 5V Port: Plug the 5V DC power adapter into the unit and connect
it to an AC wall outlet for power. (Optional, not required if the unit is
powered via PoE).
6.3 Remote Control
1PRESET 1~8 Buttons: This functionality is not currently
available and will be added in the“Phase 2” update.
1

10
6.4 IR Cable Pinout
IR Extender
Cabl
e
1
2
3
Infr
ared
Power
Ground
6.5 RS-232 Pinout and Defaults
Serial Port Default Settings
Baud Rate 19200
Data Bits 8
Parity Bits None
Stop Bits 1
Flow Control None
1
2
3
RxD
GND
TxD
3-pin
Terminal Block
1
2
3
4
5RxD
TxD
GN
D
CTS
RTS
5-pin
Terminal Block
Unit Control Serial Output

11
6.6 WebGUI Control
Device Discovery
Please obtain the “Device Discovery” software from your authorised dealer
and save it in a directory where you can easily nd it.
Connect the unit and your PC/Laptop to the same active network and
execute the“Device Discovery” software. Click on“Find Devices on
Network” and a list of devices connected to the local network will show
up indicating their current IP address.
Note: This unit defaults to DHCP mode. The current IP address can be veried
using the HDMI output (to be added in "Phase 2") or RS-232 if the Device
Discovery software is not available.
By clicking on one of the listed devices you will be presented with the
network details of that particular device.
1) IP Mode: If you choose, you can alter the static IP network settings for
the device, or switch the unit into DHCP mode to automatically obtain
proper network settings from a local DHCP server. To switch to DHCP
mode, please select DHCP from the IP mode drop-down, then click
“Save” followed by “Reboot”.
2) WebGUI Hotkey: Once you are satised with the network settings,
you may use them to connect via Telnet or WebGUI. The network
information window provides a convenient link to launch the WebGUI
directly.

12
WebGUI Overview
After connecting to the WebGUI’s address in a web browser, the
WebGUI will load and display the System tab. Click “Login" to open the
authentication window. Please enter the appropriate user name and
password then click“Enter” to log in.
Note: The default user name and password is “admin”.
After logging in, on the left side of the browser you will see the following
menu tabs where all primary functions of the unit are controllable via
the built in WebGUI. The individual functions will be introduced in the
following sections.

13
Clicking the “Logout” button within the “System” tab will automatically log
the currently connected user out of the WebGUI and return to login page.
Note: When not logged in, only the “Monitor & Control” and “System” tabs are
available.
6.6.1 Monitor & Control Tab
This tab provides easy to use drag-and-drop control over all basic routing
functionality of the transmitters and receivers that have been detected
within the local network. Transmitters are represented by the source
icon ( ) and receivers are represented by the display icon ( ). Each of
this tab’s sections control the routing of a dierent type of interface that
can be found on most compatible transmitters, receivers or transceivers.
These interfaces are: Video routing, HDMI Audio routing, Analogue Audio
routing, USB routing, IR routing, and RS-232 routing. This tab’s controls are
available even when a user is not logged in, providing basic control over
routing without exposing system critical conguration areas.
Note: Units that were previously a part of the system, but are not currently
detected will still be displayed, however they will have a disconnected icon (
) and cannot be used for routing.
1) Video Routing: Provides drag-and-drop control over the video
routing between all detected transmitters and receivers.
■Video Transmitter: This section provides drag-and-drop buttons
for all transmitters detected by the system as well as a button
target to stop one or all video streams from being transmitted.

14
Note: If a transmitter’s streams require more bandwidth than is
available, a warning icon ( ) will be displayed instead of the normal
source icon. Video output from a source displaying this icon may
become visually unstable. It is recommended to either lower the
resolution or framerate of the stream.
Source to Single Receiver Routing: To route a source to a
receiver, click and drag the source’s button on the left to the
preferred display on the right side, then release the mouse button.
If the routing was completed successfully, the newly routed
source’s name will appear below the display’s name within the
button. Clicking on any source button will change the colour of
itself, and all currently routed displays.
Note: Receivers may also be drag and dropped onto sources to
activate a new route.
Source to Multiple Receiver Routing: To route a source to
multiple receivers at the same time, click and drag the source’s
button on the left to the “All” button on the right side, then release
the mouse button. If the routing was completed successfully, the
source’s name will appear within all appropriate buttons.
Stop Stream: To stop the video streams from a single source, drag
the source down to the “Stop” button at the bottom of the window,
then release the mouse button. To stop ALL video streams, drag
the “All” button down to the “Stop” button.
■Video Receiver: This section provides drag-and-drop buttons for
all receivers detected by the system as well as a button target to
stop one or all output streams from being displayed.
Stop Stream: To stop the video stream on a single display,
drag the display down to the “Stop” button at the bottom of
the window, then release the mouse button. To stop ALL video
outputs, drag the“All”button down to the“Stop” button.

15
2) HDMI Audio Routing: Provides drag-and-drop control over the
independent HDMI audio routing of all detected transmitters and
receivers.
Note: Bitstream audio is only supported when the receiver’s HDMI audio
device setting is set to “HDMI Audio (Follow Video in Genlock Mode)”.
■HDMI Audio Transmitter: This section provides drag-and-drop
buttons for all transmitters detected by the system as well as a
button target to stop one or all independent HDMI audio streams
from being transmitted.
Source to Single Receiver Routing: To route an HDMI audio
source to a receiver, click and drag the source’s button on the left
to the preferred display on the right side, then release the mouse
button. If the routing was completed successfully, the newly
routed source’s name will appear below the display’s name within
the button. Clicking on any source button will change the colour
of itself, and all currently routed displays.
Note: Receivers may also be drag and dropped onto sources to
activate a new route.
Source to Multiple Receiver Routing: To route an HDMI audio
source to multiple receivers at the same time, click and drag the
source’s button on the left to the “All” button on the right side,
then release the mouse button. If the routing was completed
successfully, the source’s name will appear within all appropriate
buttons.

16
Stop Stream: To stop the independent HDMI audio stream from
a single source, drag the source down to the “Stop” button at the
bottom of the window, then release the mouse button. To stop
ALL independent HDMI audio streams, drag the “All” button down
to the “Stop” button.
Note: When a receiver’s HDMI Audio is set to “Follow Video in Genlock
Mode”, and scaling on that output has been disabled, the audio
output on that receiver will not be stopped.
■HDMI Audio Receiver: This section provides drag-and-drop
buttons for all receivers detected by the system as well as a button
target to stop one or all independent HDMI audio streams.
Note: When a receiver’s HDMI Audio is set to “Follow Video in Genlock
Mode” and scaling on that output has been disabled, the HDMI audio
setting is ignored and the audio embedded with the HDMI source will
always be output. In these instances a (!) mark will be displayed.
Stop Stream: To stop the HDMI audio stream on a single display,
drag the display down to the “Stop” button at the bottom of
the window, then release the mouse button. To stop ALL video
outputs, drag the“All”button down to the“Stop” button.
Note: When a receiver’s HDMI Audio is set to “Follow Video in Genlock
Mode”, and scaling on that output has been disabled, the independent
audio route will be stopped, however the HDMI embedded audio will
continue to be output normally.

17
3) Analogue Audio Routing: Provides drag-and-drop control over
the routing of analogue audio input streams between all detected
transmitters and receivers.
■Analogue Audio Transmitter: This section provides drag-and-
drop buttons for all analogue input sources detected by the
system as well as a button target to stop one or all analogue audio
streams from being transmitted.
Source to Single Receiver Routing: To route an analogue audio
source to a receiver, click and drag the source’s button on the left
to the preferred receiver on the right side, then release the mouse
button. If the routing was completed successfully, the newly
routed source’s name will appear below the receiver’s name within
the button. Clicking on any source button will change the colour
of itself, and all currently routed receivers.
Note: Receivers may also be drag and dropped onto sources to
activate a new route.
Source to Multiple Receiver Routing: To route an analogue
audio source to multiple receivers at the same time, click and
drag the source’s button on the left to the “All” button on the right
side, then release the mouse button. If the routing was completed
successfully, the source’s name will appear within all appropriate
buttons.
Stop Stream: To stop the analogue audio stream from a single
source, drag the source down to the “Stop” button at the bottom of
the window, then release the mouse button. To stop ALL analogue
audio streams, drag the “All” button down to the “Stop” button.
■Analogue Audio Receiver: This section provides drag-and-drop
buttons for all analogue audio outputs detected by the system as
well as a button target to stop the output of one or all analogue
audio streams.
Note: If the selected audio source for an analogue output has been set
to “HDMI Audio (Stereo Downmix)” that output will be marked with a
(!) and the audio output will mirror the source set on the HDMI Audio
routing page.
Stop Stream: To stop the analogue audio output on a single
receiver, drag the receiver down to the “Stop” button at the bottom
of the window, then release the mouse button. To stop ALL video
outputs, drag the“All”button down to the“Stop” button.

18
Note: If the selected audio source for an analogue output has been
set to “HDMI Audio (Stereo Downmix)” the audio output can only be
stopped from the HDMI Audio page.
4) USB Pairing: Provides drag-and-drop control over the pairing of USB
hosts (PC, laptop, etc.) and USB devices (keyboard, mouse, webcam,
etc.) between the ports detected on all transmitters and receivers.
Note: When a USB host port has enabled “Simultaneous Mode”, it can be
paired with up to 7 device endpoints. If “Simultaneous Mode” is disabled,
a USB host port can only be paired with a single USB device endpoint.
■USB Host: This section provides drag-and-drop buttons for
detected USB host ports as well as a button target to stop
communication from a host.
Host to Device Pairing: To pair a USB host with a USB device,
click and drag the USB host’s button on the left to the preferred
USB device on the right side, then release the mouse button. If
the pairing was completed successfully, the active USB host’s
name will appear below the USB device’s name within the button.
Clicking on any USB host button will change the colour of itself,
and all currently paired USB device endpoints.
Note: USB devices may also be drag and dropped onto USB hosts to
activate a new pairing.

19
Stop Host: To stop communication from a USB host, drag the USB
host down to the“Stop” button at the bottom of the window, then
release the mouse button.
■USB Device: This section provides drag-and-drop buttons for all
detected USB device endpoints as well as a button target to stop
communication from a device.
Stop Device: To stop communication from a USB device, drag
the USB device down to the“Stop” button at the bottom of the
window, then release the mouse button.
5) IR Routing: Provides drag-and-drop control over the routing of the IR
inputs and outputs detected on all transmitters and receivers.
Note: An IR output can be routed to by multiple IR inputs, however each IR
input may only be directly routed to a single IR output. If an IR input needs
to be sent to more than one output, the Global Broadcast option must be
used.
■IR Input: This section provides drag-and-drop buttons for all IR
input ports detected by the system as well as a button target to
stop one or all IR streams from being transmitted.
IR Input Global Broadcast: To broadcast an IR input to all
available IR outputs, click and drag the IR input’s button on the
left to the “All” button on the right side, then release the mouse
button. If the routing was completed successfully, the IP broadcast
address (255.255.255.255) will appear within the appropriate IR
input’s button.
Stop Stream: To stop the broadcast of an IR signal from a single IR

20
input, drag the IR input down to the“Stop” button at the bottom
of the window, then release the mouse button. To stop the
transmission of ALL IR signals, drag the “All” button down to the
“Stop” button.
■IR Output: This section provides drag-and-drop buttons for all
IR output ports detected by the system. Each IR output has an
automatically assigned IR stream IP address listed below the
output’s name.
IR Output to IR Input Routing: To connect an IR output to an
IR input, click and drag the IR output’s button on the right to the
preferred IR input on the left side, then release the mouse button.
If the routing was completed successfully, the newly routed IR
output’s IR stream IP address will appear below the IR input’s name
within its button. Clicking on any IR output button will change the
colour of itself, and all IR inputs currently routed to it.
Note: IR inputs may also be drag and dropped onto IR outputs to
activate a new route.
6) RS-232 Routing: Provides drag-and-drop control over the routing
of the RS-232 senders and receivers detected on all transmitters and
receivers. The RS-232 port on a standard extension unit contains one
sender (Rx pin) and one receiver (Tx pin).
Note: An RS-232 receiver can be routed to by multiple RS-232 senders,
however each RS-232 sender may only be directly routed to a single
RS-232 receiver. If an RS-232 sender needs to be sent to more than one
receiver, the Global Broadcast option must be used.