Cypress Hills AXCRGREY17 User manual

GREYSTONE MEDIUM STORAGE CABINET
ASSEMBLY INSTRUCTIONS
MODEL # AXCRGREY17

DO NOT RETURN
FOR REPLACEMENT PARTS OR OTHER INQUIRIES
PLEASE CONTACT US AT:
1-800-667-8992
PLEASE ENSURE TO HAVE THE COLLECTION
NAME AND DESCRIPTION FROM THE
PACKAGING OR INSTRUCTION BOOKLET

IMPORTANT : Please read this manual carefully before beginning
assembly of this product. Keep this manual for future reference.
CAUTION: Injuries and damage can occur from furniture tip over if product is
not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint
provided with the product. Consult our assembly instructions for help.
If the Furniture Anti-Tipping Restraint kit is not in the box, please contact our
customer service department in order to obtain another kit before using the
furniture.
Identify all the parts and hardware. Do not discard of the packaging until you
have checked that you have all of the parts and hardware required.
Hardware package may have spare parts.
WARNING: This item contains small parts which can be swallowed by
children and pets. Keep children and pets away during assembly. To avoid
danger of suffocation, always keep plastic bags away from children and pets.
We recommend that you assemble this unit on a carpeted floor to avoid
scratches. If using power tools, set the tool to low torque to avoid damage.
May require 2 people for ease of assembly.
SAFETY INFORMATION

Perhaps the greatest environmental damage to wood furniture comes from wide swings in
relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity
rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and
contracts unequally along different grain directions. As humidity changes, the components
of wooden objects are continually pushing and pulling against each other. This pressure
often results in parts of furniture no longer fitting together closely or becoming distorted
or breaking from their own internal stresses.
The response to relative humidity changes begins with determining the annual average RH
for your particular space. Then try to keep the RH in the space where your furniture is as
close to that average as possible, generally within about 10% up or down. De-humidify in
the summer and humidify in the winter.
Be aware that raising the temperature lowers the humidity and vice versa. Thus, modern
heating systems, which can drive down interior RH in the winter, almost invariably cause
problems for furniture. To counteract their effect, you can either modify the RH by keeping
furniture containing spaces cooler in the winter or most importantly, have a good working
humidifier for your home. A humidistat automatically works to balance the humidity in
your home so it is constant. Dry indoor air can suck enough moisture from its surroundings
to do permanent damage to wood, causing it to crack or split.
Remember, that not all woods are created equal. Two factors that help determine how
rapidly a wood will lose moisture are pore size and surface hardness. A piece made from a
dense and hard wood will dry less rapidly than pieces made from softer woods.
Furniture that is sealed and lacquered will lose moisture more slowly than an unfinished
piece while pieces with veneer finishes are not only stronger, but lose moisture more
slowly than other finishes.
To help protect your wood furniture, take these steps:
Use a humidifier, preferably one with an automatic control system that can sense the
humidity level and adjust itself accordingly. Don't over-humidify; that can damage wood
by causing it to expand and contract.
Keep furniture out of direct sunlight, which can cause it to dry out, crack and warp.
If you can avoid it, don't put furniture near heating vents. If you must, keep the piece 3
to 4 inches away from the wall, giving the heat and air space to circulate.
Dust with soft dry cloth.
Do not use liquid or aerosol products.
CARE and MAINTENANCE
IMPORTANT : Please read this manual carefully before beginning
assembly of this product. Keep this manual for future reference.

PART DESCRIPTION
TOP
QTY 1
BOTTOM
QTY 1
DIVIDER
QTY 1
LEFT SIDE
QTY 1
LEFT BACK PANEL
QTY 1
DOOR
QTY 1
ALARB
CD E
FGL
RIGHT SIDE
QTY 1
CABINET SHELF
QTY 1
GR
RIGHT BACK PANEL
QTY 1
Warning Label
PRE-ASSEMBLY INFORMATION MODEL # AXCRGREY17
NEED HELP? For help with assembly or if you are missing a part,
Please call customer service at 1-800-667-8992.

PART DESCRIPTION
PRE-ASSEMBLY INFORMATION MODEL # AXCRGREY17
NEED HELP? For help with assembly or if you are missing a part,
Please call customer service at 1-800-667-8992.
KL
SMALL DRAWER FRONT
QTY 3
LARGE DRAWER BACK
QTY 1 LARGE DRAWER BOTTOM
QTY 1
SMALL DRAWER BOTTOM
QTY 3
L
MNO
LEFT DRAWER SIDE
QTY 4
SMALL DRAWER BACK
QTY 3
P
DRAWER BOTTOM SUPPORT
QTY 1
LARGE DRAWER FRONT
QTY 1
KR
RIGHT DRAWER SIDE
QTY 4
TOP SHELF
QTY 1
H I J

HARDWARE DESCRIPTION
1
PRE-ASSEMBLY INFORMATION MODEL # AXCRGREY17
NEED HELP? For help with assembly or if you are missing a part,
Please call customer service at 1-800-667-8992.
ALLEN KEY SCREW
M6 X 30mm
QTY 34
ALLEN KEY
QTY 1
PHILLIPS SCREW
ROUND HEAD
M4 X 15mm
QTY 19
SHELF SUPPORT
QTY 6
23 4
567
PHILLIPS SCREW
M3 X 15mm
QTY 4
8
HANDLE
M4 X 25mm
QTY 6 SETS
9
MAGNET AND PLATE
QTY 1 SET
PHILLIPS SCREW
M4 X 15mm
QTY 12
CAM LOCK PIN
CAM LOCK
QTY 23 SETS
10 12
FURNITURE TIP
OVER RESTRAINT
ADJUSTABLE HINGE
QTY 2
Required -
Flathead screwdiver
Phillips screwdriver
Not Included
11
PHILLIPS SCREW
M4 X 30mm
QTY 2

DFE
H
C
B
AL
AR
GR
GL
COMPONENTS-KEY DIAGRAM MODEL # AXCRGREY17
L
I
N
KLKR
P
M
OJ
KR
KL

STEP-1
ASSEMBLY MODEL # AXCRGREY17
STEP-2
1. Attach four Cam Lock Pins 9 to back of Small Drawer Front I .
2. Align Cam Lock Pins with pre-drilled holes and attach Drawer Sides KL , KR .
3. Insert two Cam Lock 9 into pre-drilled holes on each Drawer Side KL , KR .
4. Use flathead screwdriver to secure Cam Locks.
1. Slide Small Drawer Bottom N firmly into slots on Drawer Sides KL , KR and Small
Drawer Front I .
I
9
NI
K
L
K R
K
L
K
R

ASSEMBLY MODEL # AXCRGREY17
STEP-3
STEP-4
1. Align Small Drawer Back L with Small Drawer Bottom N and press firmly into slot.
2. Attach Small Drawer Back L using two Allen Key Screws 1 through pre-drilled
holes on each Side KL , KR .
3. Use Allen Key 2 to tighten Screws. Do not over-tighten.
NOTE: The screwdriver is not
included in the hardware pack.
1. Use phillips screwdriver to attach Handle 8 to Small Drawer Front I .
Repeat Step 1 - 4 for the remaining drawers.
1
2
L
N
8
I
K
L
K
R

ASSEMBLY MODEL # AXCRGREY17
STEP-5
STEP-6
1. Attach five Cam Lock Pins 9 to back of Large Drawer Front J .
2. Align Cam Lock Pins with pre-drilled holes and attach Drawer Sides KL , KR .
3. Insert two Cam Lock 9 into pre-drilled holes on each Drawer Side KL , KR .
4. Use flathead screwdriver to secure Cam Locks.
1. Slide Large Drawer Bottom O firmly into slots on Drawer Sides KL , KR and Large
Drawer Front J .
J
9
9
J
O
K
L
K
R
K
L
K R

ASSEMBLY MODEL # AXCRGREY17
STEP-7
1. Align Cam Lock Pins with pre-drilled holes and attach Drawer Bottom Support P .
2. Insert one Cam Lock 9 into pre-drilled holes on Drawer Bottom Support P .
3. Use flathead screwdriver to secure Cam Locks.
4. Attach Large Drawer Back M to Drawer Bottom Support P using two Phillips
screws 11 .
5. Use Phillip Screwdriver to snugly tighten screw.
6. Align Large Drawer Back M with Large Drawer Bottom O and press firmly into slot.
7. Attach Large Drawer Back M using two Allen Key Screws 1 through pre-drilled
holes on each Side KL , KR .
8. Use Allen Key 2 to tighten Screws. Do not over-tighten.
21
M
11
O
9
P
NOTE: The screwdriver is not
included in the hardware pack.
K L
K
L

ASSEMBLY MODEL # AXCRGREY17
STEP-8
NOTE: The screwdriver is not
included in the hardware pack.
1. Use phillips screwdriver to attach two Handles 8 to Large Drawer Front J .
8
J

STEP-9
STEP-10
1. Attach Divider D to Top Shelf H using three Allen Key Screws 1 .
2. Use Allen Key 2 to tighten. Do not over-tighten.
1. Attach three Cam Lock Pins 9 to back of Left Side AL .
2. Align Cam Lock Pins with pre-drilled holes and attach Top Shelf H .
3. Insert three Cam Lock 9 into pre-drilled holes on Top Shelf H .
4. Use flathead screwdriver to secure Cam Locks.
5. Attach Bottom C to Left Side AL using three Allen Key Screws 1 .
6. Use Allen Key 2 to tighten Screws. Do not over-tighten.
1
2D
H
9
H
C
2
1
AL
ASSEMBLY MODEL # AXCRGREY17

STEP-11
1. Repeat Step-3 for The Right Side AR .
9
H
C
1
2
AR
AL
ASSEMBLY MODEL # AXCRGREY17

STEP-12
1. Attach Top B to Side AR , AL and Divider D using nine Allen Key Screws 1
(three screws on each Side and Divider).
2. Use Allen Key 2 to tighten screws. Do not over-tighten.
1
2
2
1
B
D
AL
AR
ASSEMBLY MODEL # AXCRGREY17

STEP-13
1. Attach Back Panels GL , GR to back frame of cabinet using nineteen Phillips
Screws Round Head 6 through pre-drilled holes.
2. Use Phillips Screwdriver to tighten screws.
NOTE: The screwdriver is not
included in the hardware pack.
6
B
GL
GR
Warning Label
Note:
ASSEMBLY MODEL # AXCRGREY17

STEP-14
ASSEMBLY MODEL # AXCRGREY17
1. Attach Adjustable Hinges 10 to Door E using Phillips Screws 4 into
pre-drilled holes on Door E .
2. Use Phillips screwdriver to attach Handle 8 to Doors
E .
8
4
10
STEP-15
10
4
1. Attach Adjustable Hinges 10 on Door E to each Side BL , BR
using Phillips Screws 4 into pre-drilled holes on each Side BL , BR .
2. Use Phillips screwdriver to snugly tighten screws.
E
E
AR

ASSEMBLY MODEL # AXCRGREY17
IMPORTANT NOTE:
Tighten the Screw marked II to fasten hinge. The door may need to
be adjusted so that all the spaces between the door and the unit sides are equal.
To adjust, follow instructions:
1. Side adjustment 4 mm
To move the door towards the side panel, loosen screw I and tighten screw II .
To move the door away from the side panel, loosen screw II and tighten screw I .
2. Depth adjustment 4 mm
Loosen screw II ( just one turn ), adjust door to desired position, re-tighten screw .
3. Height adjustment
Loosen screw 4 , adjust door to desired position, re-tighten screw .
4
II I
STEP-16

STEP-17
ASSEMBLY MODEL # AXCRGREY17
F
1. Use four Shelf Supports 3 for each Cabinet Shelf F in desired location.
2. Two Shelf Supports 3 may be used on back top of each Cabinet Shelf F as a
tipping restraint.
3
3
7
5
STEP-18
F
D
H
E
1. Attach Magnet Plates 7 to bottom corner of Door E using Phillips Screws 5 into
guide holes on Door E .
2. Attach Magnets 7 using Phillips Screws 5 into guide holes on Divider D .
3. Use Phillips screwdriver to snugly tighten screw.