Cypress Hills MARANA AXCCMAR14 User manual

MARANA LOW STORAGE CABINET
ASSEMBLY INSTRUCTIONS
MODEL # AXCCMAR14

DO NOT RETURN
FOR REPLACEMENT PARTS OR OTHER INQUIRIES
PLEASE CONTACT US AT:
1-800-667-8992
PLEASE ENSURE TO HAVE THE COLLECTION
NAME AND DESCRIPTION FROM THE
PACKAGING OR INSTRUCTION BOOKLET

IMPORTANT : Please read this manual carefully before beginning
assembly of this product. Keep this manual for future reference.
CAUTION: Injuries and damage can occur from furniture tip over if product is
not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint
provided with the product. Consult our assembly instructions for help.
If the Furniture Anti-Tipping Restraint kit is not in the box, please contact our
customer service department in order to obtain another kit before using the
furniture.
Identify all the parts and hardware. Do not discard of the packaging until you
have checked that you have all of the parts and hardware required.
Hardware package may have spare parts.
WARNING: This item contains small parts which can be swallowed by
children and pets. Keep children and pets away during assembly. To avoid
danger of suffocation, always keep plastic bags away from children and pets.
We recommend that you assemble this unit on a carpeted floor to avoid
scratches. If using power tools, set the tool to low torque to avoid damage.
May require 2 people for ease of assembly.
SAFETY INFORMATION

Perhaps the greatest environmental damage to wood furniture comes from wide swings in
relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity
rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and
contracts unequally along different grain directions. As humidity changes, the components
of wooden objects are continually pushing and pulling against each other. This pressure
often results in parts of furniture no longer fitting together closely or becoming distorted
or breaking from their own internal stresses.
The response to relative humidity changes begins with determining the annual average RH
for your particular space. Then try to keep the RH in the space where your furniture is as
close to that average as possible, generally within about 10% up or down. De-humidify in
the summer and humidify in the winter.
Be aware that raising the temperature lowers the humidity and vice versa. Thus, modern
heating systems, which can drive down interior RH in the winter, almost invariably cause
problems for furniture. To counteract their effect, you can either modify the RH by keeping
furniture containing spaces cooler in the winter or most importantly, have a good working
humidifier for your home. A humidistat automatically works to balance the humidity in
your home so it is constant. Dry indoor air can suck enough moisture from its surroundings
to do permanent damage to wood, causing it to crack or split.
Remember, that not all woods are created equal. Two factors that help determine how
rapidly a wood will lose moisture are pore size and surface hardness. A piece made from a
dense and hard wood will dry less rapidly than pieces made from softer woods.
Furniture that is sealed and lacquered will lose moisture more slowly than an unfinished
piece while pieces with veneer finishes are not only stronger, but lose moisture more
slowly than other finishes.
To help protect your wood furniture, take these steps:
Use a humidifier, preferably one with an automatic control system that can sense the
humidity level and adjust itself accordingly. Don't over-humidify; that can damage wood
by causing it to expand and contract.
Keep furniture out of direct sunlight, which can cause it to dry out, crack and warp.
If you can avoid it, don't put furniture near heating vents. If you must, keep the piece 3
to 4 inches away from the wall, giving the heat and air space to circulate.
Dust with soft dry cloth.
Do not use liquid or aerosol products.
CARE and MAINTENANCE
IMPORTANT : Please read this manual carefully before beginning
assembly of this product. Keep this manual for future reference.

PART DESCRIPTION
TOP
QTY 1 RIGHT SIDE
QTY 1
DIVIDER
QTY 1 BOTTOM SHELF
QTY 1
LEFT DOOR
QTY 1 LEFT BACK PANEL
QTY 1
CABINET SHELF
QTY 2
A BR
CD E
FL
LEFT SIDE
QTY 1
BL
RIGHT DOOR
QTY 1
FRGL
RIGHT BACK PANEL
QTY 1
GR
PRE-ASSEMBLY INFORMATION MODEL # AXCCMAR14
Warning
Label
NEED HELP? For help with assembly or if you are missing a part,
Please call customer service at 1-800-667-8992.

HARDWARE DESCRIPTION
1
Required -
Flathead screwdriver
Phillips screwdriver
Rubber mallet
Not Included
PRE-ASSEMBLY INFORMATION MODEL # AXCCMAR14
NEED HELP? For help with assembly or if you are missing a part,
Please call customer service at 1-800-667-8992.
ALLEN KEY
QTY 1
ALLEN KEY SCREW
M6 X 30mm
QTY 9
PHILLIPS SCREW ROUND HEAD
M4 X 15mm
QTY 18
HANDLE
M4 X 30 mm
QTY 2 SETS MAGNET AND PLATE
QTY 2 SETS
SHELF SUPPORT
QTY 12
PHILLIPS SCREW
M3 X 15mm
QTY 8
CAM LOCK PIN
CAM LOCK
QTY 9 SETS
WOOD DOWEL
QTY 6
PHILLIPS SCREW
M4 X 15mm
QTY 24
2 3
4 5 6
78 9
10 11 12
ADJUSTABLE HINGE
QTY 4 QTY 1 SET

A
C
E
D
E
BL
BR
FL
FR
GR
GL
COMPONENTS-KEY DIAGRAM MODEL # AXCCMAR14

STEP-1
C
D
3
1
1. Insert 2 Dowels 3 into guide holes on Divider C .
2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. 1/2 length of
Dowels should be exposed.
3. Attach Divider C to Bottom Shelf D using 3 Allen Key Screws 1 .
4. Use Allen Key 4 to tighten screws. Do not over-tighten.
ASSEMBLY MODEL # AXCCMAR14
4

STEP-2
C
D
1. Insert 4 Dowels 3 into guide holes on Bottom Shelf D ( 2 dowels on each side).
2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. 1/2 length of
Dowels should be exposed.
3. Attach 3 Cam Lock Pins 2 to each Side BL , BR using pre-drilled holes.
4. Align Cam Lock Pins with guide holes on Bottom Shelf D .
5. Insert 6 Cam Locks 2 into guide holes on Bottom Shelf D
(3 Cam Locks on each side).
6. Use flathead screwdriver to secure Cam Locks.
BL
BR
ASSEMBLY MODEL # AXCCMAR14
3
2
2

STEP-3
4
1
A
D
C
2
1. Attach 3 Cam Lock Pins 2 to middle Top A using pre-drilled holes.
2. Align Cam Lock Pins with guide holes on Divider C .
3. Insert 3 Cam Locks 2 into guide holes on Divider C .
4. Use flathead screwdriver to secure Cam Locks.
5. Attach Top A to Sides BL , BR using 6 Allen Key Screws 1
(3 screws on each Side).
6. Use Allen Key 4 to tighten Screws. Do not over-tighten.
BL
BR
ASSEMBLY MODEL # AXCCMAR14

STEP-4
ASSEMBLY MODEL # AXCCMAR14
NOTE:
The triangle ruler
is not included in
the hardware pack.
Triangle ruler
Adjust the cabinet frame before assembling the back panels.
STEP-5 Note:
1. Attach Back Panels GL , GR to back frame of Storage using 18 Phillips Screws
Round Head 5 through guide holes.
2. Use Phillips Screwdriver to tighten screws.
Warning Label
5
GR
GL

STEP-6
ASSEMBLY MODEL # AXCCMAR14
FR
FL
BR
BL
A
1. Attach Adjustable Hinges 11 to Doors FL , FR using Phillips Screws 10 into
pre-drilled holes on Doors FL , FR .
2. Use Phillips screwdriver to attach Handle 7 to Doors FL , FR .
10
11
1. Attach Adjustable Hinges 11 on Doors FL , FR to each Side BL , BR
using Phillips Screws 10 into pre-drilled holes on each Side BL , BR.
2. Use Phillips screwdriver to snugly tighten screws.
7
FLFR
11
10
STEP-7

ASSEMBLY MODEL # AXCCMAR14
IMPORTANT NOTE:
Tighten the Screw marked II to fasten hinge. The door may need to
be adjusted so that all the spaces between the door and the unit sides are equal.
To adjust, follow instructions:
1. Side adjustment 4 mm
To move the door towards the side panel, loosen screw I and tighten screw II .
To move the door away from the side panel, loosen screw II and tighten screw I .
2. Depth adjustment 4 mm
Loosen screw II ( just one turn ), adjust door to desired position, re-tighten screw .
3. Height adjustment
Loosen screw 10, adjust door to desired position, re-tighten screw .
10
II I
STEP-8

ASSEMBLY MODEL # AXCCMAR14
STEP-9
9898
DFR
FL

1. Use 4 Shelf Supports 6 for each Cabinet Shelf E in desired location.
2. 2 Shelf Supports 6 may be used on back top of each Cabinet Shelf E
as a tipping restraint.
ASSEMBLY MODEL # AXCCMAR14
shelf level 3
shelf level 2
shelf level 1
shelf support
anti - tipping
6
E
E
6
E
E
Note: Levelers on bottom of legs can be adjusted if floor is uneven.
STEP-10

12
12
NOTE: The screwdriver is not
included in the hardware pack.
WARNING
Serious or fatal crushing injuries can occur from furniture tip-over.
If the furniture tip over restraint kit is not in the box, please contact our customer
service department in order to obtain another kit before using the furniture.
FURNITURE TIP OVER RESTRAINT ASSEMBLY
STEP-11

Furniture Tip Over Restraint Instructions:
1. Attach one of the mounting brackets securely to the back edge of
the furniture. Use the shorter screw.
2. Determine where furniture is to be placed and mark location on
the wall for mounting bracket screw hole approximately 2 inches
below the bracket mounted to the furniture.
3. Drill a 3/16 inch hole in the wall. Press the plastic anchor into the
hole and gently tap until the flange on the anchor is against the
wall surface.
4. Position the bracket over the anchor and use the longer screw to
securely attach the bracket to the wall.
5. Place the furniture so the back edge is in line with the bracket on
the wall.
6. Lace an end of the nylon zip-tie strap down through each bracket.
Bring both ends together and slide the smooth side upright
through the square-shaped end and pull through to create the
7. Check to make sure the strap is securely laced and locked to the
brackets.
DO NOT put a TV or other heavy objects on top of a Low Storage
Cabinet or any other furniture not intended for use with a TV
DO NOT place heavy objects in top drawers
DO NOT let children climb or hang on drawers, doors or shelves
x
x
x
FURNITURE TIP OVER RESTRAINT ASSEMBLY