Cypress Semiconductor CY3215-DK User manual

CY3215-DK
PSoC® 1 In-Circuit Emulator Development
Kit Guide
Doc. # 001-66514 Rev. *B
Cypress Semiconductor
198 Champion Court
San Jose, CA 95134-1709
Phone (USA): 800.858.1810
Phone (Intnl): 408.943.2600
http://www.cypress.com

2 CY3215-DK PSoC 1 In-Circuit Emulator Development Kit Guide, Doc. # 001-66514 Rev. *B
Copyrights
Copyrights
© Cypress Semiconductor Corporation, 2011-2012. The information contained herein is subject to change without notice.
Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a
Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted
nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an
express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components
in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user.
The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such
use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by
and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty
provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create
derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom soft-
ware and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as speci-
fied in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source
Code except as specified above is prohibited without the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATE-
RIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described
herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein.
Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure
may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support sys-
tems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all
charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
PSoC®Designer™ is a trademark and PSoC®is a registered trademark of Cypress Semiconductor Corp. All other trade-
marks or registered trademarks referenced herein are property of the respective corporations.
Flash Code Protection
Cypress products meet the specifications contained in their particular Cypress PSoC Data Sheets. Cypress believes that its
family of PSoC products is one of the most secure families of its kind on the market today, regardless of how they are used.
There may be methods, unknown to Cypress, that can breach the code protection features. Any of these methods, to our
knowledge, would be dishonest and possibly illegal. Neither Cypress nor any other semiconductor manufacturer can guaran-
tee the security of their code. Code protection does not mean that we are guaranteeing the product as ‘unbreakable’.
Cypress is willing to work with the customer who is concerned about the integrity of their code. Code protection is constantly
evolving. We at Cypress are committed to continuously improving the code protection features of our products.

CY3215-DK PSoC 1 In-Circuit Emulator Development Kit Guide, Doc. # 001-66514 Rev. *B 3
Contents
1. Introduction 4
1.1 Kit Contents.................................................................................................................4
1.2 Additional Learning Resources....................................................................................5
1.3 Document History ........................................................................................................6
1.4 Documentation Conventions .......................................................................................6
2. Getting Started 8
2.1 Kit Installation ..............................................................................................................8
2.2 PSoC Designer..........................................................................................................11
2.3 PSoC Programmer ....................................................................................................13
3. Using ICE-Cube Connector 14
3.1 Introduction................................................................................................................14
3.1.1 Software Installation.......................................................................................14
3.2 Connecting the ICE-Cube..........................................................................................16
3.2.1 Connect using a USB Port.............................................................................16
3.2.2 Connect using a Flex Cable...........................................................................16
3.2.3 Connect using a Backward Compatibility Adapter.........................................19
3.2.4 Debug a Project .............................................................................................20
3.2.4.1 Break Points.....................................................................................22
3.2.4.2 CPU and Register Views .................................................................22
3.2.4.3 Watch Variables...............................................................................23
3.2.4.4 Trace................................................................................................24
3.2.4.5 Locals...............................................................................................24
3.3 PSoC Programmer ....................................................................................................25
4. Code Examples 28
4.1 My First Code Example .............................................................................................28
4.1.1 Project Objective............................................................................................28
4.1.2 Creating My First PSoC 1 Project..................................................................28
4.1.3 Verify Output ..................................................................................................36

4 CY3215-DK PSoC 1 In-Circuit Emulator Development Kit Guide, Doc. # 001-66514 Rev. *B
Contents

CY3215-DK PSoC 1 In-Circuit Emulator Development Kit Guide, Doc. # 001-66514 Rev. *B 4
1. Introduction
Thank you for your interest in the CY3215-DK PSoC®1 In-Circuit Emulator Development Kit. You
can use this kit with PSoC Designer™ or PSoC Programmer. The CY3215-DK provides debugging
functionality that requires two-way communication between the in-circuit emulator (ICE) and your
computer.
The MiniEval board, provided with the kit, is a programming and evaluation board that connects to
the ICE-Cube via an In-System Serial Programming (ISSP) cable and enables programming of
PSoC 1 devices. The MiniEval also includes LEDs and a potentiometer for simple evaluation and
demonstration.
The CY3215-DK Kit supports the following 8-bit PSoC 1 families, including automotive, except
CY8C25/26xxx devices.
■CY8C20x34
■CY8C20xx6A
■CY8C21x23
■CY8C21x34
■CY8C22xxx/CY8C21x45
■CY8C23x33
■CY8C24x23A
■CY8C24x94
■CY8C27x43
■CY8C28xxx
■CY8C29x66
■CY8C95xx
1.1 Kit Contents
The CY3215-DK Kit includes the following:
■ICE-Cube in-circuit emulator
■ISSP cable
■USB 2.0 cable
■Blue Cat-5e cable
■MiniEval programming board
■2 units of 28-pin DIP samples (CY8C29466-24PXI)
■ZIF socket
■CY3250 flex cable
■Backward compatibility adapter
■29000-28 PDIP kit

5 CY3215-DK PSoC 1 In-Circuit Emulator Development Kit Guide, Doc. # 001-66514 Rev. *B
Introduction
■12-V 1-A adapter
■CY3215-DK kit CD
❐PSoC Designer installation file
❐PSoC Programmer installation file
❐Bridge Control Panel installation file (packaged along with PSoC Programmer)
❐Kit guide
❐Quick start guide
❐Release notes
Inspect the contents of the kit; if any parts are missing, contact your nearest Cypress sales office for
further assistance.
1.2 Additional Learning Resources
Visit http://www.cypress.com for additional learning resources in the form of data sheets, technical
reference manual and application notes.
■For more information regarding PSoC Designer functionality and releases:
http://www.cypress.com/go/psocdesigner
■For more information regarding PSoC Programmer, supported hardware and COM layer:
http://www.cypress.com/go/psocprogrammer
■For a list of PSoC Designer-related trainings:
http://www.cypress.com/?rID=40543
■For more information on CY3250-29xxxQFN ICE Pod Schematic:
http://www.cypress.com/?rID=3451
■For more information on CY3250-FLEXCABLE Mechanical Layout Drawing:
http://www.cypress.com/?rID=3451
■For more information on CY3250-29xxxQFN ICE Pod Mechanical Layout Drawing:
http://www.cypress.com/?rID=3451

CY3215-DK PSoC 1 In-Circuit Emulator Development Kit Guide, Doc. # 001-66514 Rev. *B 6
Introduction
1.3 Document History
1.4 Documentation Conventions
Table 1-1. Revision History
Revision PDFCreation
Date Origin of Change Description of Change
** 01/27/2011 RKPM Initial version of kit guide
*A 05/11/2011 RKPM Added Code Examples chapter. Updated images in section
2.1. Content updates throughout the document.
*B 01/30/2012 PAVA Added information on the devices that CY3215-DK sup-
ports in the Introduction chapter. Updated Figure 2-2.
Table 1-2. Document Conventions for Guides
Convention Usage
Courier New Displays file locations, user entered text, and source code:
C:\...cd\icc\
Italics Displays file names and reference documentation:
Read about the sourcefile.hex file in the PSoC Designer User Guide.
[Bracketed, Bold]Displays keyboard commands in procedures:
[Enter] or [Ctrl] [C]
File >> Open Represents menu paths:
File >> Open >> New Project
Bold Displays commands, menu paths, and icon names in procedures:
Click the File icon and then click Open.
Times New Roman Displays an equation:
2 + 2 = 4
Text in gray boxes Describes cautions or unique functionality of the product.

7 CY3215-DK PSoC 1 In-Circuit Emulator Development Kit Guide, Doc. # 001-66514 Rev. *B
Introduction

CY3215-DK PSoC 1 In-Circuit Emulator Development Kit Guide, Doc. # 001-66514 Rev. *B 8
2. Getting Started
This chapter describes how to install the CY3215-DK PSoC 1 In-Circuit Emulator Development Kit.
2.1 Kit Installation
To install the CY3215-DK kit, follow these steps:
1. Insert the kit CD into the CD/DVD drive of your PC. The CD is designed to auto-run and the kit
installer startup screen appears.
Note You can also download the latest kit installer from http://www.cypress.com/go/CY3215-DK.
Three different types of installers are available for download.
a. CY3215-DK_ISO: This file (ISO image) is an archive file of the optical disc provided with the
kit. You can use this to create an installer CD or extract information using WinRar or similar
tools.
b. CY3215-DK_ Single Package: This executable file installs the contents of the kit CD, which
includes PSoC Programmer, PSoC Designer, and user documents.
c. CY3215-DK_Single Package (without prerequisites): This executable file installs only the kit
contents, which includes kit user documents.
2. Click Install CY3215-DK to start the installation, as shown in Figure 2-1.
Figure 2-1. Kit Installer Startup Screen

9 CY3215-DK PSoC 1 In-Circuit Emulator Development Kit Guide, Doc. # 001-66514 Rev. *B
Getting Started
Note If auto-run does not execute, double-click the cyautorun.exe file on the root directory of the
CD, as shown in Figure 2-2. To access the root directory, click Start > My Computer > CY3215-
DK <drive:>.
Figure 2-2. CD Root Directory
3. In the InstallShield Wizard,choose the folder location to install the setup files. You can change
the location of the folder for the setup files using Change,as shown in Figure 2-3.
4. Click Next to launch the kit installer.
Figure 2-3. InstallShield Wizard
5. On the Product Installation Overview screen, select the installation type that best suits your
requirement. The drop-down menu has three options: Typical, Complete,and Custom, as
shown in Figure 2-4.
6. Click Next to start the installation.