Cypress CLUX-SDI2CSS User manual

CLUX-SDI2CSS
SDI to CV/SV Scaler with
Audio
Operation Manual
CLUX-SDI2CSS

Disclaimers
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes
no commitment to update or to keep current the information
contained in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
Copyright Notice
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
- electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise - without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.0 May 2011
Trademark Acknowledgments
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

Safety Precautions
Please read all instructions before attempting to unpack or install or
operate this equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
 Always follow basic safety precautions to reduce the risk of
re, electrical shock and injury to persons.
 To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
 Never spill liquid of any kind on or into this product.
 Never push an object of any kind into this product through
module openings or empty slots, as you may damage parts.
 Do not attach the power supply cabling to building surfaces.
 Do not allow anything to rest on the power cabling or allow it to
be abused by persons walking on it.
 To protect the equipment from overheating, do not block the
slots and openings in the module housing that provide
ventilation.
Revision History
Version No Date Summary of Change
VR0 20110513 Preliminary Release
VR1 20110928 Spec. Transmission Typo

Table of Contents
1
1
1
2
3
4
4
5
6
7
7
7
8
8
9
10
1. Introduction ……………………..……………………...…........….…….
2. Applications …………………..………………….……...................…..
3. Package Contents ………………………...........……….................…
4. Features …………………………………………......……........…...……
5. Specications ………………………………...……..........………....….
6. Operation Controls and Functions ……………...……..............……
6.1 Front Panel ..............................................................................
6.2 Rear Panel .…………………………………..…….......…...….…
7. OSD Menu and Function List ...................………..........…..…....…...
7.1 Display .................…......................……………..........…..…....….
7.2 Color .........…..….....................................................................….
7.3 SDI Audio ...................................................................…..…....….
7.4 Factory Reset ............................................................…..…....….
7.5 Information ...............................................................…..…....….
8. Connection and Installation ….………………….........…..…..…......
9. Acronyms …......................................................................................

1. Introduction
The SDI to CV/SV Scaler with Audio allows SD, HD and 3G-SDI signals to be
display on CV/SV displays while ensuring high bit rates of 2.970 Gbps gives
you fast signal transmission without signal loss. For professional this means that
it is now easier to distribute and extend your SDI signal while giving you the
ability to display your work on the existing CV/SV displays. Further, the design
of coaxial and L/R audio output allows user to output audio with both digital
and analog format and the loop-through 3G-SDI design also benet user to
enjoy both SDI and CV/SV display synchronously.
2. Applications
Broadcast video signal sending to SDI display
3G SDI signal convert into CV/SV signal
3. Package Contents
SDI to CV/SV Scaler with Audio
5V/2.6A DC power adaptor
Operation Manual
1

4. Features

Operation at 2.970Gbps, 2.970/1.001Gbps, 1.485Gbps, 1.485/1.001Gbps
and 270Mbps

Supports SMPTE 425M (Level A and Level B), SMPTE 424M, SMPTE 292M,
SMPTE 259M-C

Equalized and re-clocked loop output

Alternative audio output to coaxial and analog 2CH

Auto video mode detection (3G/HD/SD)

Conversion from SMPTE 425M level B to Level A for 1080p 50/59.94/60 4:2:2
10-bit

Supports NTSC/PAL output
2

5. Specications
SMPTE Standard 425M Level A & B, 424M, 292M, 259M-C
SDI Transmission Rates 2.970 Gbps and 2.970/1.001 Gbps, 1.485Gbps,
1.485/1.001Gbps, and 270Mbps
Input Port 1 x BNC (SD/HD/3G-SDI)
Output Port 1 x BNC (SD/HD/3G-SDI),
1 x CV, 1 x SV, 1 x Coaxial, 1 x R/L RCA Jack
Video Output Support NTSC/PAL
SDI In/Out Support Timing 480i, 576i, 720p@50/59.94/60, 1080i@50/59.94/
60, [email protected]/24/25/29.97/30/50/59.94/60
1080Ps[email protected]/24/25/29.97/30
Power Supply 5V DC/ 2.6A (US/EU standards,
CE/FCC/UL certied)
ESD Protection Human body model: ±8kV (air-gap discharge)
±4kV (contact discharge)
SDI Cable Distance 3G up to 100M (BELDEN 1694A Cable)
HD up to 200M (BELDEN 1694A Cable)
SD up to 300M (BELDEN 1694A Cable)
Dimensions (mm) 180(W) x 142(D) x 25(H)
Weight(g) 435
Chassis Material Aluminum
Silkscreen Color Gray
Operating Temperature 0˚C ~ 40˚C / 32˚F ~ 104˚F
Storage Temperature -20˚C ~ 60˚C / -4˚F ~ 140˚F
Relative Humidity 20 ~ 90% RH (Non-condensing)
Power Consumption (W) 8.5
3

6. Operation Controls and Functions
6.1 Front Panel
POWER3GHDSD MENUENTER
-
+
NTSC PAL
3G SDI to Video Scaler CLUX-SDI2CSS
① ② ③ ④ ⑤ ⑥ ⑦
① Power LED: This blue LED will illuminate when the device is connected with
power supply.
② 3G LED: This green LED illuminate when the input SDI signal is with 3G
format.
③ HD LED: This green LED illuminate when the input SDI signal is with HD
format.
④ SD LED: This green LED illuminate when the input SDI signal is with SD
format.
⑤ MENU: Press this button to enter/exit the OSD menu.
⑥ ENTER: Press this button to confirm your selection. Press both ENTER and
– buttons together to switch output timing to NTSC format instantly or
press both ENTER and + buttons together to switch output timing to PAL
format. After the selelction press ENTER to confirm the output format.
⑦ -/+: Press these buttons to move up or down the OSD selections.
4

6.2 Rear Panel
SDI IN SDI OUT AUDIO OUT DC 5V
COAXIAL R L
S VIDEOVIDEO
① ② ③ ④ ⑤ ⑥
① SDI IN: This slot is where you connect the SDI source output for SDI signal
sending to be display on screen.
② SDI OUT: This slot is where you connect the SDI display with SDI cable for
input source display.
③ AUDIO OUT COAXIAL: This slot is where you connect the amplifier with
coaxial cable and from amplifier to speaker
④ AUDIO OUT R/L: These slots are where you connect the speaker or
amplifier with RCA jack for audio signal display.
⑤ These slots are to connected with display TV or monitor with CV/SV
cable(s).
⑥ DC 5V: Plug the 5V DC power supply into the unit and connect the
adaptor to AC wall outlet. Blue LED will illuminate when the power is ON.
5

7. OSD Menu and Function List
1st Layer 2nd Layer 3rd Layer
Display
Output NTSC
PAL
Size
Full
Over Scan
Under 1
Under 2
Letter Box
Pan Scan
Exit
Color
Contrast 0~255(105)
Brightness 0~192(96)
R 0~255(128)
G 0~255(128)
B 0~255(128)
R Offset 0~64(32)
G Offset 0~64(32)
B Offset 0~64(32)
Exit
SDI Audio
Group 1
Group 2
Group 3
Group 4
Auto
Off
Factory Reset Yes
Information Input/Output &
Revision
6