D-Link SharePort DIR-825 User manual

Additional documentation is also available on the D-Link website
DIR-825
Quick Installation Guide
AC1200 Wi-Fi Gigabit Router & LTE Outdoor CPE
DWP-812KT

Contents
English 1
Polski 7

Quick Installation Guide 1
ENGLISH
Before You Begin
This Quick Installation Guide gives you step-by-
step instructions for setting up your DIR-825
AC1200 Wi-Fi Gigabit Router and connecting
it to your DWP-812KT LTE Outdoor CPE. The
model you have purchased may appear slightly
different from the one shown in the illustrations.
For more detailed information about the router,
please refer to the User Manual.
Package Contents
This package should include the following items:
• DIR-825 AC1200 Wi-Fi Gigabit Router
• DWP-812KT LTE Outdoor CPE
• Power adapter (DIR-825)
• Power adapter (DWP-812KT)
• PoE injector (DWP-812KT)
• 10 meter Ethernet cable
• 2 x 1 meter Ethernet cable
• Mounting bracket
• 4 x M6 screw
• 4 x M3 screw
• 2 x U-bolt clamp
• Quick Installation Guide
If any of the above items are damaged or
missing, please contact your local D-Link reseller.
Installing and mounting the DWP-812KT and
connecting it to the DIR-825 requires the use
of a drill with a 4 mm drill bit and a Phillips
screwdriver.
Note: Using a power supply with a different
voltage than the one recommended for the
devices will cause damage and void the
warranty for these products.
System Requirements
• Safari 8, Google Chrome 48, Microsoft
Internet Explorer 10, Microsoft Edge
20.10240, Mozilla Firefox 44, or Opera 35
• A PC with an Ethernet or Wi-Fi adapter
Hardware Overview
DIR-825 Front Panel LED Indicators
13 4
Figure 1: DIR-825 Front Panel LED Indicators
# LED Description
1Power Indicates whether the DIR-825 is
receiving power.
2 Internet
Off No Ethernet cable attached.
Slow
Blinking
Cable attached, but no
Internet connection.
Solid
Green
Active connection; no data
is being transferred.
Fast
Blinking
Active connection; data is
currently being transferred.
3 LAN Indicates whether the router is
connected to devices on its LAN ports.
42.4G/5G
WLAN
Indicates whether the 2.4 GHz and 5
GHz interfaces are enabled or disabled.
5 WPS Indicates whether WPS is enabled.
6 USB Indicates whether a USB storage
device is connected to the DIR-825.
Table 1: DIR-825 Front Panel LED
Indicator Descriptions
2 5 6

2Quick Installation Guide
ENGLISH
DWP-812KT Rear Panel
LED Indicators
RF
PWR
ETH
SIM
Figure 3: Front Panel Interface
# LED Description
1 RF
Indicates the strength of the LTE
signal. More bars signify a stronger
signal.
2PWR Indicates whether the device is
receiving power.
3 ETH
Indicates whether the DWP-812KT
is connected to another device on
its Ethernet port.
4 SIM
Indicates whether an active SIM
card is inserted into the SIM card
slot.
Table 3: DWP-812KT Rear Panel LED Indicators
DWP-812KT Interface Connectors
Figure 4: DWP-812KT Interface Connectors
# Connector Description
1SIM Card
Slot
2FF SIM card slot.
2Ethernet
LAN Port
10/100/1000 Gigabit Ethernet
LAN port.
Table 4: DWP-812KT Interface Connectors
DIR-825 Rear Panel
Interface Connectors
LAN4 LAN3 LAN2 LAN1
WAN USB
WPS
WiFi
POWER
- • +
Figure 2: DIR-825 Rear Panel Interface Connectors
# Interface Description
1 WIFI Press to enable or disable Wi-Fi.
2 WPS
Press to start the WPS process and
create an encrypted connection to
a WPS client.
3Ethernet
LAN Ports
10/100/1000 Gigabit Ethernet
LAN ports.
4Ethernet
WAN Port
10/100/1000 Gigabit Ethernet
WAN port.
5USB 2.0
Port
USB 2.0 port for a storage device.
6Power
Input
Input for the power adapter.
7Power
Button
Press to power the DIR-825 on
or off.
Table 2: DIR-825 Rear Panel Interface
Connector Descriptions
1
2 3 4 5 6 7
1 2
1
2
3
4

Quick Installation Guide 3
ENGLISH
Hardware Installation
Before You Begin
Observe the following precautions to help
prevent shutdowns, equipment failures, and
personal injury:
• Install the DIR-825 in a cool and dry place.
• Install the DIR-825 in a site free from strong
electromagnetic sources, vibration, dust,
excessive moisture, and direct sunlight.
• Place in an unobstructed area with a clear
mobile signal. Avoid metal boxes, brick
walls, and other dense materials.
• Visually inspect the power connector and
make sure that it is fully secure.
• Do not stack any devices on top of the
DIR-825.
Setting Up the DWP-812KT
The DIR-825 is designed to connect to a 4G
LTE network through the DWP-812KT. Check
that you have an active LTE SIM card from your
service provider.
1. Unscrew the covers from the SIM card slot
and Ethernet LAN port on the bottom
panel of the DWP-812KT.
2. Insert an active LTE SIM card into the SIM
card slot.
SIM
PoE
Figure 5: Inserting a SIM Card and Ethernet Cable
3. Connect an Ethernet cable to the LAN port
on the bottom panel of the DWP-812KT,
threading it through the hole on the
Ethernet cover. Connect the other end to
the PoE port on the included PoE injector.
4. Replace both covers on the bottom panel
of the DWP-812KT.
Figure 6: Attaching the Covers
Establishing an Internet Connection
with the DIR-825
Connecting to the DWP-812KT
1. Ensure that the DWP-812KT is powered on
and set up with an active SIM card. (Refer
to Setting Up the DWP-812KT below.)
2. Use an Ethernet cable to connect the WAN
port on the rear panel of the DIR-825 to the
data port on the PoE injector.
3. Connect the power adapter to the power
input on the DIR-825 and plug the adapter
into a nearby power outlet.

4Quick Installation Guide
ENGLISH
Connecting to the
Management Computer
Connecting via Ethernet
1. Use an Ethernet cable to connect the
LAN port on the rear panel of the DIR-825
to an Ethernet port on the management
computer.
2. Turn on the router by pressing the POWER
button on its back panel.
3. Make sure that the Ethernet adapter of
your PC is configured to obtain an IP
address automatically.
Connecting via Wi-Fi
1. Turn on the DIR-825 by pressing the
POWER button on its back panel.
2. Make sure that the Wi-Fi adapter of your
PC is configured to obtain an IP address
automatically.
3. Connect to the network DIR-825-XXXX
(for operating in the 2.4 GHz band) or
DIR-825-5G-XXXX (for operating in the 5 GHz
band), substituting the last four characters
of the DIR-825's MAC address for XXXX. Use
the WPS PIN from the barcode label as the
network key.
Mounting the DWP-812KT
Place the DWP-812KT outside, in an open area.
Obstructions such as windows or concrete
or wooden walls affect the transmission and
reception of wireless signals. Keep the DWP-812KT
away from appliances that produce strong electric
or magnetic fields such as dish satellite antennas.
Mounting on a Pole
1. Attach the U-shaped bracket to the pole
using the provided mounting ties.
Figure 7: Attaching the Bracket to the Pole
2. Attach the other mounting bracket to the
rear panel of the DWP-812KT using four
mounting screws.
RF
PWR
ETH
SIM
RF
PWR
ETH
SIM
Figure 8: Attaching the Rear
Panel Mounting Bracket
3. Place the mounting bracket over the
U-shaped bracket. Position the DWP-812KT
at the desired angle and attach it with four
screws.
Figure 9: Attaching the Bracket to the Pole

Quick Installation Guide 5
ENGLISH
Mounting on a Wall
1. Place the U-shaped bracket against the
wall in the desired position. Use a 4 mm
drill bit to make four holes approximately
30 mm deep, then insert four wall anchors
into the holes.
2. Use four screws to attach the U-shaped
bracket to the wall.
3. Use four screws to attach the mounting
bracket to the rear panel of the
DWP-812KT, or eight screws to stack two
mounting brackets together, allowing
the DWP-812KT's angle to be adjusted
horizontally and vertically.
Figure 10: Attaching Two Mounting Brackets
4. Place the mounting brackets over the
U-shaped bracket. Position the DWP-812KT
at the desired angle and attach it with four
screws.
Completed Installation
Once the installation is complete and the DIR-825 is
connected to the DWP-812KT, your network should
resemble Figure 11: Completed Installation.
Figure 11: Completed Installation
Management Options
1. First, ensure that the DIR-825 and
DWP-812KT are both connected. Launch
a web browser. Enter 192.168.0.1 in the
address field of your browser.
2. When you first access the web-based
interface, you will be prompted to enter a
new admin password for the UI. Type the
password in the first field and retype it in
the second field to confirm it.
3. After changing the admin password, use
the menu in the left part of the page to
configure the router.
It is recommended that you immediately disable
the DWP-812KT's PIN Code Request feature to
prevent problems when the device is powered
off. For detailed instructions on how to do this,
refer to the User Manual.
Wired LAN
Clients
Wireless LAN
Clients
DIR-825
DWP-812KT
PoE Injector
LTE

6Quick Installation Guide
ENGLISH
Additional Information
If you are encountering problems setting up
your network, please refer to the user manual.
Additional help is available online. To find out
more about D-Link products or marketing
information, please visit the D-Link support
website at http://dlink.com/support/.
Warranty Information
The D-Link Limited LifetimeWarranty information
is available at the following website:
http://warranty.dlink.com/
TECHNICAL SUPPORT eu.dlink.com/support

Quick Installation Guide 7
POLSKI
Wstęp
Skrócona instrukcja instalacji wyjaśnia jak,
krok po kroku zainstalować zestaw IDU/ODU.
Zakupione urządzenia mogą się nieznacznie
różnić od widocznych na ilustracjach. Aby
uzyskać szczegółowe informacje dotyczące
routera, pobierz Instrukcję obsługi ze strony
dlink.com
Zawartość opakowania
Wewnątrz opakowania znajdują się następujące
elementy:
• Router DIR-825 AC1200 Wi-Fi Gigabit
• Antena zewnętrzna DWP-812KT LTE
Outdoor CPE
• Zasilacz (DIR-825)
• Zasilacz (DWP-812KT/Adapter PoE)
• Adapter PoE (PoE injector) (DWP-812KT)
• 1x Kabel Ethernet 10m
• 2x Kabel Ethernet 1m
• Uchwyt montażowy
• 4x śruby M6
• 4x śruby M3
• 2x zaciski w kształcie litery U
• Skrócona instrukcja instalacji
Jeśli w zestawie brakuje jakiegokolwiek
elementu, skontaktuj się ze Sprzedawcą.
Instalacja i montaż anteny zewnętrznej DWP-
812KT oraz podłączenie jej do routera DIR-825
wymaga wiertarki z wiertłem o średnicy 4mm
oraz wkrętaków Phillips (krzyżowych).
UWAGA: Stosowanie zasilacza o innym napięciu
niż zalecane spowoduje uszkodzenie i utratę
gwarancji na zakupione urządzenia.
Wymagania systemowe
• Safari 8, Google Chrome 48, Microsoft
Internet Explorer 10, Microsoft Edge
20.10240, Mozilla Firefox 44 lub Opera 35
• Komputer PC z portem Ethernet lub
modułem Wi-Fi
Opis urządzenia
DIR-825 Przedni panel
ze wskaźnikami LED
13 4
Rysunek 1: DIR-825 Przedni panel
ze wskaźnikami LED
#LED Opis
1Power Wskazuje czy urządzenie jest podłączone do
źródła zasilania.
2Internet
Nie świeci Wskazuje brak połączenia
kablem Ethernet z anteną
zewnętrzną.
Jednostajne
miganie
Wskazuje poprawne
połączenie kablem z antena
zewnętrzną oraz brak
połączenia z Internetem.
Świeci Wskazuje połączenie z
Internetem oraz brak
transmisji danych.
Szybkie
nieregularne
miganie
Wskazuje połączenie z
Internetem oraz aktywną
transmisję danych.
2 5 6

8Quick Installation Guide
POLSKI
DWP-812KT Przedni panel ze
wskaźnikami LED
RF
PWR
ETH
SIM
Rysunek 3: Interfejsy na przednim panelu
#LED Opis
1RF Wskazuje siłę sygnału LTE. Więcej
słupków oznacza silniejszy sygnał.
2PWR Wskazuje, czyurządzeniejest zasilane.
3ETH
Wskazuje, czy DWP-812KT jest
podłączone do innego urządzenia
przez port Ethernet.
4SIM Wskazuje, czy aktywna karta SIM jest
umieszczona w gnieździe karty SIM.
Tabela 3: DWP-812KT Opis wskaźników
LED na przednim panelu
DWP-812KT Złącza interfejsów
Rysunek 4: DWP-812KT Złącza interfejsów
#Złącze/
Gniazdo
Opis
1Slot karty
SIM
Gniazdo karty 2FF SIM.
2Port LAN Port LAN 10/100/1000 Gigabit
Ethernet.
Tabela 4: DWP-812KT Złącza interfejsów
#LED Opis
3LAN Wskazuje, czy router jest połączony z
urządzeniami poprzez porty LAN.
42.4G/5G
WLAN
Wskazuje, czy moduły Wi-Fi 2,4 GHz i 5 GHz są
włączone czy wyłączone.
5WPS Wskazuje, czy WPS jest włączony.
6USB Wskazuje, czy dysk USB jest podłączony do
DIR-825.
Tabela 1: Opis wskaźników LED na
przednim panelu DIR-825
DIR-825 Złącza na tylnym panelu
urządzenia
LAN4 LAN3 LAN2 LAN1
WAN USB
WPS
WiFi
POWER
- • +
Rysunek 2: Złącza na tylnym panelu urządzenia
#Interfejs Opis
1WIFI Naciśnij, aby włączyć lub wyłączyć Wi-Fi.
2WPS
Naciśnij, aby rozpocząć proces parowania
używając funkcji WPS, celem utworzenia
szyfrowanego połączenia z drugim
urządzeniem.
3Porty LAN Porty LAN 10/100/1000 Gigabit Ethernet.
4Port WAN Port WAN 10/100/1000 Gigabit Ethernet.
5Port USB
2.0
Port USB 2.0 do podłączenia dysku USB.
6Wejście
zasilania
Gniazdo do podłączenia zasilacza.
7Przycisk
zasilania
Naciśnij,abywłączyć lub wyłączyć DIR-825.
Tabela 2: Opis interfejsów na tylnym panelu DIR-825.
1
2 3 4 5 6 7
1 2
1
2
3
4