D-Link DES-1316 - Switch User manual

1
This Quick Installation Guide gives step-by-step instructions for setting up the D-Link
DES-1316 PoE Web-Smart Switch. The model you have purchased may appear slightly
different from those shown in the illustrations. For more detailed information about the
switch, its components, making network connections and technical specifications,
please refer to the User’s Manual on master CD included with your switch.
Check Your Package Contents
If any item is found missing or damaged, please contact your local reseller for
replacement.
©2004 D-Link System, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective
holders. Software and specifications subject to change without notice.
16-Port 10/100Mbps Ethernet Web Smart Switch
with 8-Port PoE
DES-1316
16-Port 10/100Mbps Ethernet Web
Smart Switch with 8-Port PoE
CD-Rom(Containing manual and Utility
Installation)
Before Your Be
g
in
A
C powe
r
cord (Suitable for your area’s
electrical power connections)

2
Setup The DES-1316 PoE Web Smart Switch
The setup of the Switch can be performed using the following steps:
A. Install DES-1316 in a fairly cool and dry place. See Technical Specifications for the
acceptable temperature and humidity operating ranges.
B. Install the Switch in a site free from strong electromagnetic field generators (such as
motors), vibration, dust, and direct exposure to sunlight.
C. Leave at least 10cm of space at the front and rear of the hub for ventilation.
D. Install the Switch on a sturdy, level surface that can support its weight, or in an EIA
standard-size equipment rack. For information on rack installation, see the next
section, Rack Mounting.
E. When installing the Switch on a level surface, attach the rubber feet to the bottom of
each device. The rubber feet cushion the hub and protect the hub case from
scratching.
Rack Mounting
ES-1316 can be mounted in an EIA standard-size, 19-inch rack, which can be placed in
a wiring closet with other equipment. Attach the mounting brackets at the switch’s front
panel (one on each side), and secure them with the provided screws.
Combine the Switch with the provided screws
Then, use screws provided with the equipment rack to mount each switch in the rack.
Mount the Switch in the rack

3
Connecting Network Cable
DES-1316 support 16 10/100M Ethernet ports and Port 1 ~ port 8 are PoE Enable ports,
these PoE port will automatically activated when a compatible terminal is identified, the
Switch will supply power through the Ethernet port to the connected PoE device.
For the Legacy devices that are not yet compatible, the PoE port will not offer the power
to this device. This feature allows users to freely and safely mix legacy and Power over
LAN compatible devices on their network.
The Switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and it runs both in half
and full duplex mode using two pair of Category 5 cable.
These RJ45 ports are Auto-MDI type port. The Switch can auto transform to MDI-II or
MDI-X type, so you can just make an easy connection that without worrying if you are
using a standard or crossover RJ45 cable.
AC Power
The Switch used the AC power supply 100-240V AC, 50-60 Hz. The power switch is located at the
rear of the unit adjacent to the AC power connector and the system fan. The switch’s power
supply will adjust to the local power source automatically and may be turned on without having
any or all LAN segment cables connected.

4
Identifying External Components
This chapter describes the front panel, rear panel, and LED indicators of the Switch.
Front Panel
The figure below shows the front panels of the Switch.
PoE Ports
┌――┐
└――――┘ └―――┘
LEDIndicators EthernetPorts
Front panel of the Switch
LED Indicator:
Comprehensive LED indicators display the status of the switch and the network (see the
LED Indicators chapter below).
PoE Ports (Port 1~8):
These ports are PoE Enable ports, the PoE port will automatically activated when a
compatible terminal is identified, the Switch will supply power through the Ethernet port
to the connected PoE device.
For the Legacy devices that are not yet compatible, the PoE port will not offer the power
to this device. This feature allows users to freely and safely mix legacy and Power over
LAN compatible devices on their network
These ports support network speeds of either 10Mbps or 100Mbps, and can operate in
half- and full- duplex transfer modes. These ports also supports automatic MDI/MDIX
crossover detection function gives true “plug and play” capability, just need to plug-in the
network cable to the hub directly and don’t care if the end node is NIC (Network
Interface Card) or switch and hub.
Ethernet Ports (Port 9~16):
These ports support network speeds of either 10Mbps or 100Mbps, and can operate in
half- and full- duplex transfer modes. These ports also supports automatic MDI/MDIX

5
crossover detection function gives true “plug and play” capability, just need to plug-in the
network cable to the hub directly and don’t care if the end node is NIC (Network
Interface Card) or switch and hub
Note: When the port was set to “Forced Mode”, the Auto MDI/MDIX will be disabled.
Rear Panel
Rear panel of the Switch
AC Power Connector:
This is a three-pronged connector that supports the power cord. Plug in the female connector of
the provided power cord into this connector, and the male into a power outlet. Supported input
voltages range from 100-240V AC at 50-60Hz.
Reset:
The Reset button is to reset all the setting back to the factory default.
Note: Be sure that you recorded the setting of your device, else all the setting will
be erased when pressing the “Reset” button.
Understanding LED ndicators
The front panel LEDs provides instant status feedback, and, helps monitor and troubleshoot when
needed.
Figure 5. LED indicators of the Switch
AC Power Connector
Reset Button

6
Power and CPU LEDs
POWER: Power Indicator
On When the Power LED lights on, the Switch is receiving power.
Off When the Power turns off or the power cord has improper connection.
CPU: Management Indicator
Blinking When the CPU is working, the CPU LED is blinking.
On/Off The CPU is not working.
Ports 1~8 PoE port status LEDs
Link/ACT: Link/Activity
On
When the Link/ACT LED lights on, the respective port is successfully connected
to an Ethernet network.
Blinking
When the Link/ACT LED is blinking, the port is transmitting or receiving data on
the Ethernet network.
Off No link.
100Mbps
On
When the 100Mbps LED lights on, the respective port is connected to a 100Mbps
Fast Ethernet network.
Off When the respective port is connected to a 10Mbps Ethernet network
PoE Status
Green When the PoE device was connected and the port supplies power successfully.
Red
When the PoE port have the following failure happens:
 PoE power short circuit
 PoE Power over current
 PoE Power fault
Off No Powered Device is detected

7
Ports 9~16 Ethernet port status LEDs
Link/ACT: Link/Activity
On
When the Link/ACT LED lights on, the respective port is successfully connected
to an Ethernet network.
Blinking
When the Link/ACT LED is blinking, the port is transmitting or receiving data on
the Ethernet network.
Off No link.
100Mbps
On
When the 100Mbps LED lights on, the respective port is connected to a 100Mbps
Fast Ethernet network.
Off When the respective port is connected to a 10Mbps Ethernet network

8
Installing the Web Management Utility
The following gives instructions guiding you through the installations of the Web
Management utility.
1. Insert the Utility CD in the CD-Rom Drive.
2. From the Start menu on the Windows desktop, choose Run.
3. In the Run dialog box, type D:\Web Management Utility\setup.exe (D:\ depends
where your CD-Rom drive is located) and click OK.
4. Follow the on-screen instructions to install the utility.
5. Upon completion, go to Program Files -> web_management_utility and execute
the Web Management utility. (Figure 1.)
Figure 1. Web Management Utility

9
Configuring the Switch
The 16-Port 10/100Mbps Ethernet Web Smart Switch with 8-Port PoE has a Web GUI
interface for smart switch configuration. The Switch can be configured through the Web
Browser. A network administrator can manage, control and monitor the switch from the
local LAN. This section indicates how to configure the Switch to enable its smart
functions including:
 Port Setting (Speed/Disable and Flow Control)
 VLAN Setting (802.1Q VLAN)
 Trunking
 Port Mirroring
 QoS Setting
 PoE Setting
 System Setting
 Device status and Statistic
Login
Before you configure this device, note that when the Web Smart Switch is configured
through an Ethernet connection, make sure the manager PC must be set on same the
IP network. For example, when the default network address of the default IP address of
the Web Smart Switch is 192.168.0.1, then the manager PC should be set at
192.168.0.x (where x is a number between 2 and 254), and the default subnet mask is
255.255.255.0.
Open Internet Explorer 5.0 or above Web browser.
Enter IP address http://192.168.0.1 (the factory-default IP address setting) to the
address location. (Figure 2.)
Figure 2.

10
Or through the Web Management Utility, you do not need to remember the IP Address,
select the device shown in the Monitor List of the Web Management Utility to settle the
device on the Web Browser.
When the following dialog page appears, remain enter the default password "admin"
and press Login to enter the main configuration window. (Figure 3.)
Figure 3.
After entering the password, the main page comes up, the screen will display the device
status. (Figure 4.)
Figure 4. Device Status