D-Link DI-LB60 User manual

2 D-Link Systems, Inc.
DI-LB604 Install GuideSystem Requirements
System Requirements
 Ethernet-based Cable or DSL Modem
 Computers with Windows, Macintosh, or Linux-based
operating systems with an installed Ethernet adapter

Internet Explorer Version 6.0 or Netscape Navigator 7.0 and
above
Package Contents

D-Link Systems, Inc. 3
DI-LB604 Install Guide Hardware Overview
Power LED
A solid light indicates a
proper connection to the
proper power supply.
Status LED
This LED will be off to indicate
proper operation and it will blink
during data transmission.
WAN LEDs
A solid light indicates a connection
on the WAN port. These LEDs blink
during data transmission.
Local Network LEDs
A solid light on each port
indicates a connection to an
Ethernet enabled computer.
These LEDs blink during data
transmission.
Hardware Overview
Front Panel

4 D-Link Systems, Inc.
DI-LB604 Install GuideHardware Overview
WAN Ports
This is for the connection of
an Ethernet cable to your
Cable or DSL modem.
LAN Ports
These are the connections for Ethernet cables
to Ethernet enabled computers.
Reset Button
Pressing this button restores the Router to its
original factory default settings.
Power Receptor
Back Panel Connections

D-Link Systems, Inc. 5
DI-LB604 Install Guide Connecting the DI-LB604
Connecting The DI-LB604 Load
Balancing Router To Your Network
A. First, connect the power adapter to the receptor at the back
panel of the DI-LB604 and then plug the other end of the power
adapter to a wall outlet or power strip. The Power LED will turn
ON to indicate proper operation.
B. 1. Power off your Cable or DSL modem; some devices
may not have an on/off switch and will require you to
unplug the power adapter. Now, the DI-LB604 should be
powered on and the Cable/DSL modem should be turned off.
2. Cable/DSL modem (Power Off) – DI-LB604 (Power On)
Connect an Ethernet cable to the Ethernet jack located
on the Cable/DSL modem. After the Ethernet cable is
securely connected, power on the Cable/DSL modem
by turning on the unit or plugging in the power adapter.
3. Cable/DSL modem (Power On) – DI-LB604 (Power On)
Insert the other end of the Ethernet cable to the WAN PORT on
the back panel of the DI-LB604. The WAN LED light will illuminate
to indicate proper connection. If the WAN LED is not illuminated,
please go back to step B1 and repeat the instructions.
C. Insert an Ethernet cable to LAN port 1 on the back panel of the
DI-LB604 and an available Ethernet port on the network adapter
in the computer you will use to configure the DI-LB604. The LED
light for LAN Port 1 will illuminate to indicate proper connection.
(Note: The LAN Ports on the DI-LB604 are Auto-MDI/MDIX.
Meaning you can use a straight-through or crossover Ethernet
cable to the LAN Ports.)

6 D-Link Systems, Inc.
DI-LB604 Install GuideConnecting the DI-LB604
Getting Started

D-Link Systems, Inc. 7
DI-LB604 Install Guide Using The Setup Wizard
Once you have logged
in, the Home screen will
appear.
Using The Setup Wizard
The logon screen will
appear.
Open your Web browser
and type “http://192.168.0.1”
into the URL address box.
Then press the Enter or
Return key.
Type “admin” for the username
and leave the password field
blank.
Click OK
Click Run Wizard

8 D-Link Systems, Inc.
DI-LB604 Install GuideUsing The Setup Wizard
You will see the following
screens:
Click Next
Click Next
Choose your time zone
from the drop down list.
Click Next
Set up your new password.
You have the option to
establish a password for the
username “admin”.

D-Link Systems, Inc. 9
DI-LB604 Install Guide Using The Setup Wizard
Click Next
Click Next
If you are unsure of which
setting to select, please
contact your Internet Service
Provider.
Click Next
Select the type of Internet
Connection that is attached
to WAN1.
Enter the needed information
for the type of connection you
have chosen.
Select the type of Internet
connection that is attached to
WAN2.

10 D-Link Systems, Inc.
DI-LB604 Install GuideUsing The Setup Wizard
Click Next
Your Setup is Complete!
Click Next
Enter the needed information
for the type of connection you
have chosen.