D-Link DFL-210 - NetDefend - Security Appliance User manual

Network
Security Firewall
This Quick Guide will guide you through the installation Process. You are
only moments away from using your new D-Link Network Security Product
Building Networks for People
DFL-210

1.Before You Begin
1.1 Check Your Package Contents....................................................................1
2.Indentifying Components
2.1 FrontView.................................................................................................2
2.2 Rear View.................................................................................................2
2.3 LED Indicators...........................................................................................3
2.4 DefaultInterface AttributeDefinition..........................................................3
3.Connecting the DFL-210
3.1 Setting up Firewall to your Network...........................................................4
4.Configure DFL-210
4.1 Configure your Computer’s IP...................................................................5
4.2 UsingtheSetupWizard..............................................................................6
5.Appendix
5.1 How to Configure Static IP Manually on Microsoft Windows XP...............15
5.2 How to Configure Static IP Manually on Apple MAC OS X............................16
6.Statement
DFL-210 Quick Installation Guide

1.1 Check Your Package Contents
Your NetDefend Network Security Firewall package should
contain all the items listed below. If any of these items is found
damaged or missing in your package, report it to your reseller
immediately for replacement.
One (1) DFL-210 NetDefend™ Network Security Firewall
One (1) 5V DC Power Adapter
One (1) Console Cable (RS-232 cable)
One (1) Ethernet (CAT5 UTP/Straight Through) Cable
One (1) Ethernet (CAT5 UTP/Cross-over) Cable
One (1) CD-ROM (containing QIG/Manual )
DFL-210
Before You Begin 1
01
DFL-210
Power Adapter
Console Cable CD-ROM
Ethernet Cable
(Cross-over)
Ethernet Cable
(Straight-Through)

Identifying Components 2
The following illustrates the front panel of the DFL-210 and
explains the front panel’s key components:
2.1 Front View
02
1. Power LED
2. Status LED
3. WAN LED
4. DMZ LED
5. LAN LED
Power indication of the DFL-210.
System status indication of the DFL-210.
WAN port status indication of the DFL-210.
DMZ port status indication of the DFL-210.
LAN port status indication of the DFL-210.
Note:
WAN interface does not support Auto MDI/MDI-X
(Automatic cable detection for Straight-through and Crossover
function).
1 2 3 4 5
2.2 Rear View
1. Console Port
2. LAN Ports
3. DMZ Port
4. WAN Port
5. Reset
6. Power Receptor
Connects to RS-232 console cable that connects to PC.
These are for the connection of Ethernet cables to the internal network.
This is for the connection of an Ethernet cable to an DMZ network.
This is for the connection of an Ethernet cable to a Cable or DSL modem.
This is for resetting system conguration to factory defaults.
This is for the connection of the power adaper to a wall outlet or power strip.
1 3 4 62 5

2.4 Default Interface Attribute Definition
Note:
NetDefendOS only allows Web GUI access from LAN port by default
for security consideration. Please refer to user manual for more
detail about how to change this conguration.
DFL-210 Quick Installation Guide
03
Wording on
Front plate
Default name
in rewall
Default interface
type denition
Default interface
IP Address
Default
DHCP Status
WAN WAN DHCP client N/A Enabled
DMZ DMZ Static IP 172.17.100.254/24 Disable
Ports: 1~4 LAN Static IP 192.168.1.1/24 Disable
2.3 LED Indicators
Status
Solid green
Light off
Solid green
Light off
Blinking green
Solid green
Blinking green
Light off
Solid green
Blinking green
Light off
Solid green
Blinking green
Light off
Description
The device is powered on.
The device is powered off.
System is operating properly.
The device is not working.
System is defective, such rmware
upgrade fail.
Link present
Port is sending or receiving data.
No link
Link present
Port is sending or receiving data.
No link
Link present
Port is sending or receiving data.
No link
Color
Green
Green
Green
Green
Green
LED
Power
Status
WAN
DMZ
LAN

Connecting the DFL-210 3
04
3.1 Connecting Firewall to Your Network
A. First, connect the power cord to the receptor at the back panel of
the DFL-210 and then plug the other end of the power cord to a
wall outlet or power strip. Then powered on the DFL-210 using
the on/off switch. Now the Power LED will turn ON to indicate
proper operation. After the power LED turns on, you need to wait
1-2 minutes for the DFL-210 to boot up completely.
B. Connect an Ethernet cable from the DFL-210 to your Cable/
DSL modem. If the Cable/DSL modem is powered on, wait for
the WAN1 LED on the DFL-210 to light up to show a proper
connection. Otherwise, turn off your Cable/DSL modem, connect
the Ethernet cable from the DFL-210 to your Cable/DSL modem,
and turn on the Cable/DSL modem. Some Cable/DSL modems
may not have an on/off switch and will require you to unplug the
power adapter.
Note:
The default management IP address of the DFL-210 is
192.168.1.1. If you have are using a router that uses DHCP,
there may be a conict if the router uses the same IP address as
the DFL-210. If this is the case, either disconnect the DFL-210
from the router and change the management IP address of the
DFL-210, or change the DHCP settings on your router.
C. Insert an Ethernet cable to the LAN1 port on the front panel of
the DFL-210 and connect it to a port on your network hub or
switch. The LED light above the Ethernet port on the DFL-210
will illuminate to indicate proper connection
D. Connecting the computer that you will use to congure the
DFL-210 to the network hub or switch.

4.1 Configure Your Computer’s IP Address
Make sure that the network adapter in your computer is congured
to use a static IP address with 192.168.1.1 as default gateway and
255.255.255.0 as netmask. Instructions on how to congure the
network adapter can be found in the appendix.
When you have completed the steps in this Quick Installation
Guide, your connected network should look similar to this:
Configure DFL-210 4
05
Cable/DSL Modem
DFL-210
Switch
Internal
Network
DMZ
Network
(optional)
Computer1 Computer2

Type the default
Username/Password
Username: admin
Pasword: admin
and click Login
4.2 Using the Setup Wizard
The DFL-210 provides Web based conguration. You can congure your DFL-
210 through Internet Explorer 6 and later or Firefox 1.0 and later browser in MS
Windows, Macintosh or UNIX based platforms.
Activate your browser, and ensure your built-in Pop-Up Blocker has been
disabled, so that the Pop-Up Blocker will not block the Startup Wizard while you
initiate the NetDefend Firewall for the rst time.
Additionally, in order to reduce the impact of Pop-Up Blocker, a user-friendly
mechanism has beem implemented in NetDefend Firewalls. A "Startup Wizard"
button is shown on the toolbar since rmware v2.20. This button is available on
the WebGUI while the appliance is initiated with Conguration Version 1. Once
you complete conguration and save/activate the setting, the Startup Wizard
button will be removed automatically from the toolbar while you login WebGUI
next time.
Now, let's start on WebGUI login, type the IP address of the DFL-210, e.g.
https://192.168.1.1, in the Location (for Netscape) or Address (for IE) eld and
press "Enter".
Log on to the DFL-210 web interface.
To start using the DFL-210 web interface you need to log on using the
default username and password.
DFL-210 Quick Installation Guide
Open your Web browser and
type https://192.168.1.1 / into
the URL address box. Then
press the Enter or Return key.
06
Note:
DFL-210 allows either HTTP or a secure HTTPS connection
from any management host. However, for security reason, by
default only a secure HTTPS connection is allowed.

Step1 - Welcome to the DFL-210 setup wizard!
Step2 - Set up rewall administrator password
First Enter the
username that you want
to use for the admin
account.
Enter the password
that you want to use
for the admin account.
DFL-210 Quick Installation Guide
This wizard will guide
you through the setup of
your DFL-210
Click Next
07
Click Next

2
Step 3 - Set up time and date
Click Set time and date
button for setting device
08
Click Next
Select the appropriate date
Enter the appropriate time
Click OK
DFL-210 Quick Installation Guide