D-Link DVG-N5402G/ACF User manual

Quick Installation Guide
DVG-N5402G/ACF
Wireless AC1200 Dual Band Gigabit Router
ith Fiber WAN Port, 3G/LTE Support, 2 FXS
Ports, 1 PSTN (lifeline) Port, and USB Port

DVG-N5402G/ACF Quick Installation Guide
BEFO E YOU BEGIN
Delivery Package
•Router DVG-N5402G/ACF
•Power adapter DC 12V/2A
•Ethernet cab e (CAT 5E)
•Two RJ-11 te ephone cab es
•“Quick Installation Guide” (brochure).
If any of the items are missing, p ease contact your rese er.
The “User Manual” and “Quick Installation Guide” documents are avai ab e
on D-Link website (see www.d ink.ru).
!Using a power supply with a different voltage rating than the one
included will cause damage and void the warranty for this product.
2

DVG-N5402G/ACF Quick Installation Guide
Default Settings
Domain name of device dlinkrouter.local.
IP address of device 192.168.8.254
Username (login) admin
Password admin
Name of wireless
network (SSID)
2.4GHz DVG-N5402G
5GHz DVG-N5402G-5G
Network key (PSK password)
see WPS PIN on the barcode
abe on the bottom pane of
the device
!
Router DVG-N5402G/ACF with defau t settings cannot connect to the
Internet. To get started, p ease set your own password for access to the
web-based interface and change the WLAN name (SSID); then, if
needed, configure other settings recommended by your ISP.
3

DVG-N5402G/ACF Quick Installation Guide
System Requirements and Equipment
•A computer with any operating system that supports a web browser.
•A web browser to access the web-based interface of the router:
◦App e Safari 8 and ater
◦Goog e Chrome 48 and ater
◦Microsoft Internet Exp orer 10 and ater
◦Microsoft Edge 20.10240 and ater
◦Mozi a Firefox 44 and ater
◦Opera 35 and ater.
•A NIC (Ethernet or Wi-Fi adapter) to connect to the router.
•An 802.11a, b, g, n, or ac Wi-Fi adapter to create a wire ess network.
•SFP transceiver to connect to a fiber optic ine.
•Ana og phone.
•A USB modem (when it is necessary to connect to the Internet via mobi e
operators' networks)1.
!
Your USB modem shou d be equipped with an active SIM card of your
operator.
Some operators require subscribers to activate their USB modems prior
to using them. P ease, refer to connection guide ines provided by your
operator when conc uding the agreement or p aced on its website.
For some mode s of USB modems, it is required to disab e the PIN
code check on the SIM card prior to connecting the USB modem to the
router.
1 Contact your operator to get information on the service coverage and fees.
4

DVG-N5402G/ACF Quick Installation Guide
CONNECTING TO PC
PC with Ethernet Adapter
1. Connect an Ethernet cab e between any of LAN ports ocated on the back
pane of the router and the Ethernet port of your PC.
2. To connect via USB modem: connect your USB modem to the USB port2
ocated on the back pane of the router.
!In some cases you wi need to reboot the router after connection of the
USB modem.
3. To connect the device to a fiber optic line: connect your SFP transceiver
to the SFP port, then connect the fiber optic cab e to the SFP transceiver.
4. To connect the device to an Ethernet line: in the web-based interface of
the router, se ect the router's LAN port that wi be used as the WAN port
and create an Ethernet WAN connection. Then connect an Ethernet cab e
between an avai ab e Ethernet port of the router and the Ethernet ine.
!P ease connect the router to the ISP's Ethernet ine on y after setting the
WAN port and creating the Internet connection.
5. Connect the power cord to the power connector port on the back pane of
the router, then p ug the power adapter into an e ectrica out et or power
strip.
6. Turn on the router by pressing the ON/OFF button on its back pane .
Then make sure that your PC is configured to obtain an IP address automatica y
(as DHCP c ient).
2 It is recommended to use a USB extension cab e to connect a USB modem to the
router.
5

DVG-N5402G/ACF Quick Installation Guide
Obtaining P Address Automatically
(OS Windows 7)
1. C ick the Start button and proceed to the Control Panel window.
2. Se ect the Network and Sharing Center section. (If the Contro Pane
has the category view (the Category va ue is se ected from the View by
drop-down ist in the top right corner of the window), choose the View
network status and tasks ine under the Network and Internet
section.)
3. In the menu ocated on the eft part of the window, se ect the Change
adapter settings ine.
4. In the opened window, right-c ick the re evant Local Area Connection
icon and se ect the Properties ine in the menu disp ayed.
5. In the Local Area Connection Properties window, on the
Networking tab, se ect the Internet Protocol Version 4 (TCP/IPv4)
ine. C ick the Properties button.
6

DVG-N5402G/ACF Quick Installation Guide
6. Make sure that the Obtain an IP address automatically and Obtain
DNS server address automatically choices of the radio buttons are
se ected. C ick the OK button.
7. C ick the OK button in the connection properties window.
7

DVG-N5402G/ACF Quick Installation Guide
PC with Wi-Fi Adapter
1. To connect via USB modem: connect your USB modem to the USB port3
ocated on the back pane of the router.
!In some cases you wi need to reboot the router after connection of the
USB modem.
2. To connect the device to a fiber optic line: connect your SFP transceiver
to the SFP port, then connect the fiber optic cab e to the SFP transceiver.
3. To connect the device to an Ethernet line: in the web-based interface of
the router, se ect the router's LAN port that wi be used as the WAN port
and create an Ethernet WAN connection. Then connect an Ethernet cab e
between an avai ab e Ethernet port of the router and the Ethernet ine.
!P ease connect the router to the ISP's Ethernet ine on y after setting the
WAN port and creating the Internet connection.
4. Connect the power cord to the power connector port on the back pane of
the router, then p ug the power adapter into an e ectrica out et or power
strip.
5. Turn on the router by pressing the ON/OFF button on its back pane .
6. Make sure that the Wi-Fi adapter of your PC is on. As a ru e, modern
notebooks with bui t-in wire ess NICs are equipped with a button or
switch that turns on/off the wire ess adapter (refer to your PC documents).
If your PC is equipped with a p uggab e wire ess NIC, insta the software
provided with your Wi-Fi adapter.
Then make sure that your Wi-Fi adapter is configured to obtain an IP address
automatica y (as DHCP c ient).
3 It is recommended to use a USB extension cab e to connect a USB modem to the
router.
8

DVG-N5402G/ACF Quick Installation Guide
Obtaining P Address Automatically and
Connecting to Wireless Network (OS Windows 7)
1. C ick the Start button and proceed to the Control Panel window.
2. Se ect the Network and Sharing Center section. (If the Contro Pane
has the category view (the Category va ue is se ected from the View by
drop-down ist in the top right corner of the window), choose the View
network status and tasks ine under the Network and Internet
section.)
3. In the menu ocated on the eft part of the window, se ect the Change
adapter settings ine.
4. In the opened window, right-c ick the re evant Wireless Network
Connection icon. Make sure that your Wi-Fi adapter is on, then se ect
the Properties ine in the menu disp ayed.
5. In the Wireless Network Connection Properties window, on the
Networking tab, se ect the Internet Protocol Version 4 (TCP/IPv4)
ine. C ick the Properties button.
9

DVG-N5402G/ACF Quick Installation Guide
6. Make sure that the Obtain an IP address automatically and Obtain
DNS server address automatically choices of the radio buttons are
se ected. C ick the OK button.
7. C ick the OK button in the connection properties window.
8. To open the ist of avai ab e wire ess networks, se ect the icon of the
wire ess network connection and c ick the Connect To button or eft-
c ick the network icon in the notification area ocated on the right side of
the taskbar.
10