D-Link DSL-2640U User manual

Quick Installation Guide
DSL-2640U
Wireless N150 ADSL2+ Router

DSL-2640U Quick Installation Guide
BEFORE YOU BEGI
Delivery Package
•Router DSL-2640U
•Power adapter DC 12V/0.5A
•RJ-11 telepho e cable
•Ether et cable
•Splitter
•“Quick Installation Guide” (brochure).
If a y of the items are missi g, please co tact your reseller.
The “User Manual” a d “Quick Installation Guide” docume ts are available
o D-Li k website (see www.dli k.ru).
!Using a power supply with a different voltage rating than the one
included will cause damage and void the warranty for this product.
2

DSL-2640U Quick Installation Guide
Default Settings
Domain name of device dlinkrouter.local.
IP address of device 192.168.1.1
Username (login) admin
Password admin
ame of wireless network (SSID) DSL-2640U
etwork key (PSK)
see WPS PIN o the
barcode label o the back
pa el of the device
3

DSL-2640U Quick Installation Guide
System Requirements and Equipment
•A computer with a y operati g system that supports a web browser.
•A web browser to access the web-based i terface of the router:
◦Apple Safari 8 a d later
◦Google Chrome 48 a d later
◦Microsoft I ter et Explorer 10 a d later
◦Microsoft Edge 20.10240 a d later
◦Mozilla Firefox 44 a d later
◦Opera 35 a d later.
•A NIC (Ether et or Wi-Fi adapter) to co ect to the router.
•A 802.11b, g, or Wi-Fi adapter to create a wireless etwork.
4

DSL-2640U Quick Installation Guide
CO ECTI G TO PC
PC with Ethernet Adapter
1. Co ect a Ether et cable betwee a y of LAN ports located o the back
pa el of the router a d the Ether et port of your PC.
2. To connect the router to a DSL line: co ect a pho e cable betwee the
DSL port of the router a d the ADSL OUT port of the splitter. Co ect
your pho e to the PHO E port of the splitter. The co ect a other
pho e cable betwee a pho e jack a d the ADSL I port of the splitter.
3. To connect the device to an Ethernet line: please co ect the router to
the ISP's Ether et li e o ly after setti g the WAN port a d creati g the
I ter et co ectio (see the Initial Configuration Wi ard sectio , page
16).
4. Co ect the power cord to the power co ector port o the back pa el of
the router, the plug the power adapter i to a electrical outlet or power
strip.
5. Tur o the router by pressi g the O /OFF butto o its back pa el.
The make sure that your PC is co figured to obtai a IP address
automatically (as DHCP clie t).
5

DSL-2640U Quick Installation Guide
Obtaining P Address Automatically
(OS Windows 7)
1. Click the Start butto a d proceed to the Control Panel wi dow.
2. Select the etwork and Sharing Center sectio . (If the Co trol Pa el
has the category view (the Category value is selected from the View by
drop-dow list i the top right cor er of the wi dow), choose the View
network status and tasks li e u der the etwork and Internet
sectio .)
3. I the me u located o the left part of the wi dow, select the Change
adapter settings li e.
4. I the ope ed wi dow, right-click the releva t Local Area Connection
ico a d select the Properties li e i the me u displayed.
5. I the Local Area Connection Properties wi dow, o the
etworking tab, select the Internet Protocol Version 4 (TCP/IPv4)
li e. Click the Properties butto .
6

DSL-2640U Quick Installation Guide
6. Make sure that the Obtain an IP address automatically a d Obtain
D S server address automatically choices of the radio butto s are
selected. Click the OK butto .
7. Click the OK butto i the co ectio properties wi dow.
7

DSL-2640U Quick Installation Guide
PC with Wi-Fi Adapter
1. To connect the router to a DSL line: co ect a pho e cable betwee the
DSL port of the router a d the ADSL OUT port of the splitter. Co ect
your pho e to the PHO E port of the splitter. The co ect a other
pho e cable betwee a pho e jack a d the ADSL I port of the splitter.
2. To connect the device to an Ethernet line: please co ect the router to
the ISP's Ether et li e o ly after setti g the WAN port a d creati g the
I ter et co ectio (see the Initial Configuration Wi ard sectio , page
16).
3. Co ect the power cord to the power co ector port o the back pa el of
the router, the plug the power adapter i to a electrical outlet or power
strip.
4. Tur o the router by pressi g the O /OFF butto o its back pa el.
5. Make sure that the Wi-Fi adapter of your PC is o . As a rule, moder
otebooks with built-i wireless NICs are equipped with a butto or
switch that tur s o /off the wireless adapter (refer to your PC docume ts).
If your PC is equipped with a pluggable wireless NIC, i stall the software
provided with your Wi-Fi adapter.
The make sure that your Wi-Fi adapter is co figured to obtai a IP address
automatically (as DHCP clie t).
8

DSL-2640U Quick Installation Guide
Obtaining P Address Automatically and
Connecting to Wireless Network (OS Windows 7)
1. Click the Start butto a d proceed to the Control Panel wi dow.
2. Select the etwork and Sharing Center sectio . (If the Co trol Pa el
has the category view (the Category value is selected from the View by
drop-dow list i the top right cor er of the wi dow), choose the View
network status and tasks li e u der the etwork and Internet
sectio .)
3. I the me u located o the left part of the wi dow, select the Change
adapter settings li e.
4. I the ope ed wi dow, right-click the releva t Wireless etwork
Connection ico . Make sure that your Wi-Fi adapter is o , the select
the Properties li e i the me u displayed.
5. I the Wireless etwork Connection Properties wi dow, o the
etworking tab, select the Internet Protocol Version 4 (TCP/IPv4)
li e. Click the Properties butto .
9

DSL-2640U Quick Installation Guide
6. Make sure that the Obtain an IP address automatically a d Obtain
D S server address automatically choices of the radio butto s are
selected. Click the OK butto .
7. Click the OK butto i the co ectio properties wi dow.
8. To ope the list of available wireless etworks, select the ico of the
wireless etwork co ectio a d click the Connect To butto or left-
click the etwork ico i the otificatio area located o the right side of
the taskbar.
10

DSL-2640U Quick Installation Guide
9. I the ope ed wi dow, i the list of available wireless etworks, select the
wireless etwork DSL-2640U a d click the Connect butto .
10. I the ope ed wi dow, e ter the etwork key (see WPS PIN o the
barcode label o the back pa el of the device) i the Security key field
a d click the OK butto .
11. Wait for about 20-30 seco ds. After the co ectio is established, the
etwork ico will be displayed as the sig al level scale.
!
If you perform i itial co figuratio of the router via Wi-Fi co ectio ,
ote that immediately after cha gi g the wireless default setti gs of the
router you will eed to reco figure the wireless co ectio usi g the
ewly specified setti gs.
11

DSL-2640U Quick Installation Guide
CO FIGURI G ROUTER
Connecting to Web-based nterface
Start a web browser. I the address bar of the web browser, e ter the domai
ame of the router (by default, dlinkrouter.local) with a dot at the e d
a d press the Enter key. Also you ca e ter the IP address of the device (by
default, 192.168.1.1).
!
If the error “ The page cannot be displayed ” (or “ Unable to display the
page ”/“ Could not connect to remote server ”) occurs upo co ecti g to
the web-based i terface of the router, make sure that you have properly
co ected the router to your computer.
If the device has ot bee co figured previously or the default setti gs have
bee restored, after access to the web-based i terface the I itial Co figuratio
Wizard ope s (see the Initial Configuration Wi ard sectio , page 16).
12

DSL-2640U Quick Installation Guide
If you co figured the device previously, after access to the web-based i terface
the logi page ope s. E ter the user ame (admin) i the Username field
a d the password you specified i the Password field, the click the LOGI
butto .
If you e ter a wro g password several times, the web-based i terface will be
blocked for a while. Please wait for o e mi ute a d ree ter the password you
specified.
13

DSL-2640U Quick Installation Guide
The Summary page displays ge eral i formatio o the router a d its
software.
14

DSL-2640U Quick Installation Guide
The Home page displays li ks to the most freque tly used pages with device's
setti gs.
The web-based i terface of the router is multili gual. You ca select the
eeded la guage upo the i itial co figuratio of the web-based i terface of
the router or i the System / Configuration sectio of the me u.
Other setti gs of the router are available i the me u i the left part of the
page. Go to the releva t sectio a d select the eeded page or ru the wizard
i the Initial Configuration sectio .
15

DSL-2640U Quick Installation Guide
nitial Configuration Wizard
I order to start the I itial Co figuratio Wizard ma ually, go to the Initial
Configuration sectio .
Click the OK butto a d wait u til the factory default setti gs are restored.
If you perform i itial co figuratio of the router via Wi-Fi co ectio , please
make sure that you are co ected to the wireless etwork of DSL-2640U (see
the WLAN ame (SSID) i the Default Settings sectio , page 3) a d click the
EXT butto . The click the START butto .
If the device has ot bee co figured previously or the default setti gs have
bee restored, the I itial Co figuratio Wizard starts automatically upo
access to the web-based i terface or upo ope i g a web site o the I ter et.
16

DSL-2640U Quick Installation Guide
1. Click YES i order to leave the curre t la guage of the web-based
i terface or click O to select a other la guage.
2. O the ext page, click the CO TI UE butto .
17

DSL-2640U Quick Installation Guide
Selecting Operation Mode
I order to co ect your device to a ADSL li e, o the Device mode page,
from the Connection method list, select the ADSL value. I this mode you
ca co figure a WAN co ectio , set your ow setti gs for the wireless
etwork, co figure LAN ports to co ect a STB or VoIP pho e, a d set your
ow password for access to the web-based i terface of the device.
I order to co ect your device to a private Ether et li e, o the Device
mode page, from the Connection method list, select the Ethernet (LA )
value. I this mode you ca co figure o e of the router's LAN port as the
WAN port, co figure a WAN co ectio , set your ow setti gs for the wireless
etwork, co figure LAN ports to co ect a STB or VoIP pho e, a d set your
ow password for access to the web-based i terface of the device.
Whe the operatio mode is selected, click the EXT butto .
18

DSL-2640U Quick Installation Guide
Conguring LAN Port as WAN Port
This co figuratio step is available for the Ethernet (LA ) mode.
1. O the Device connection page, select the WA /LA port.
2. Click the EXT butto .
19

DSL-2640U Quick Installation Guide
Conguring Ethernet WAN Connection
This co figuratio step is available for the Ethernet (LA ) mode.
!
You should co figure your WAN co ectio i accorda ce with data
provided by your I ter et service provider (ISP). Make sure that you have
obtai ed all ecessary i formatio prior to co figuri g your co ectio .
Otherwise co tact your ISP.
1. O the Internet connection type page, from the Connection type
list, select the co ectio type used by your ISP a d fill i the fields
displayed o the page.
Static IPv4: Fill i the followi g fields: IP address, Subnet mask,
Gateway IP address, a d D S IP address.
Static IPv6: Fill i the followi g fields: IP address, Prefix, Gateway IP
address, a d D S IP address.
20