D-Link DWR Series User manual

CONFIGURATION GUIDE
For DWR Series Routers
www. d l i n k.co.in

UNBOXING & CONNECTING
SETUP
WIRELESS SETUP
Configuration Guide
for DWR series routers

Configuration Guide
for DWR series routers

HOW TO ACCESS THE ROUTER
4) If you have the computer with Wi-Fi
then, go to wireless utility to display
available Wireless networks & select
the Wi-Fi name of device. (Default
Wi-Fi name is dlink_DWR_113). By
default there is no security /
password for this network.
5) If you don’t have Wi-Fi enabled
computer then you can connect
the lan cable provided in the box
between any lan port of the router
and computer lan port.
3) Connect the power adaptor to
device and power on the device.
Power LED should be green.
2)
1)
Connect the Wi-Fi Antenna to
the router.
Unbox the router.

HOW TO ACCESS THE ROUTER
6)
7)
8) You will be prompt for username
and password. By default Username
is admin and password is blank.
9) You will get the configuration page
of the DWR serier router
After getting connected to router.
Open the browser (such as Internet
Explorer, Mozilla, Crome etc.)
Type http://192.168.0.1 in address
bar and press enter to get the
configuration page of the router.

CONFIGURING INTERNET
10) To setup the internet connection click
on Setup. You will see the multiple
options on Left side main configuration
menus. Click on Internet.
11) In DWR series routers multiple types of
internet connections are supported.
12) To connect the router with wired
internet connection, kindly connect
the internet cable to WAN port of
the router, which is at the back side.
13) Now click on Internet Connection
Setup Wizard.
14) This Wizard will guide you through
step by step config. There are 4 main
steps as follows. Click next to proceed.
Wired Connection:-
a. DHCP Connection
b. Static IP Connection
c. PPPoE Connection
d. PPTP Connection
e. L2TP Connection
3G/4G USB Connection

CONFIGURING INTERNET
15) At first step Device administration
password needs tobe configured. After
password is provided Click on Next.
16) Setup the Time Zone, For India set
the time to GMT+05.30 INDIA and
Press Next.
19) Now Internet Setup is complete
with DHCP type of connection.

CONFIGURING INTERNET
20) PPPoE connection:- It is an dial Up
connection Type, in this ISP provides
an Username and Password for the
connection. Click Next.
21) Put the Username and password
provided by ISP. IP address is optional.
Service Name will be your ISP name
this is also Optional Click Next.
22) Now Internet Setup is complete
with PPPoE type of connection.
23) DWR series supports PPTP and L2TP
clients as Internet connection.

CONFIGURING INTERNET
24) Connection Type 3G :- In this
connection type, you can use your USB
internet dongle to get the internet.
25) For this type of connection select
3G as option in step 3 & Click Next.
27) Now Internet Setup is complete
with internet type as 3G Dongle.
26) Select Dial-Up Profile:- Manual
Select Country: - Others
Select Telecom: - Others
Select 3G Network:- Let it be Default.
Select Username: - Refer the Table.
Select the password:- Refer the Table.
Dial Number:- Refer the Table.
Select Authentication:- Auto.
APN:- Refer the table.
Press NEXT.
ISP APN
Access
NO
Username Password
Airtel
airtelgprs.com
*99#
blank
blank
Aircel
aircelgprs
*99#
blank
blank
Vodafone
www
*99#
blank
blank
Tata Docomo
3G
tata.docomo.internet
*99#
blank blank
Reliance 3G
rcomnet / smartnet
*99#
blank
blank
BSNL
bsnlnet
*99#
blank
blank
MTNL
mtnl.net
*99#
blank
blank
Idea
internet
*99#
blank
blank
Uninor
uninor
*99#
blank
blank
Tata CDMA
blank
#777
internet
internet
Reliance
CDMA
blank #777
10 digit dongle no
10 digit dongle
no
MTS
blank
#777
[email protected]
mts

28) Static Ip Connection:- In static IP
connection Service Provider provides
an IP address, subnet mask default
gateway details. For this in Step 3
Select Connection type as Static IP.
29) In next step provide all details and
press Next.
30) After providing all the details Click
on next or Connect.
31) To verify the internet connection
status , kindly click on StatusTab.
CONFIGURING INTERNET

32) To configure the Wireless Lan network,
Click on Setup then Wire less Settings
Tab on left side of the page.
33) Click on the Wireless Connection
Setup Wizard.
34) There are three steps to configure
the wireless Lan network.
Click on NEXT.
35) At first step configure your Wi-Fi
name. This name will be broadcasted
as wifi name. By default it will be
dlink_DWR_113. Press NEXT.
36) At step 2 select the security type.
Best:- This mode supports WPA2
security Type.
Better:- This mode supports WPA
Security type.
Good:- This mode supports WEP
security type.
None:- No security.
WIRELESS CONFIGURATION

37) Select Network Authentication As
BEST and click Next.
39) Wi-Fi setup is completed and click
on Save.
38) In this step, provide the wireless
security password. This password
will be asked when there is new a
user wants to connect to your
network. This password should be
minimum 8 Digit. It could be alpha
numeric. Press NEXT.
WIRELESS CONFIGURATION