D-Link DVG-5402SP User manual

Quick Installation Guide
DVG-5402SP
VoIP Router
Package Contents
Using a power adapter with a
different voltage rating will damage
this product and void the warranty.
DVG-5402SP
VoIP Router
CD-ROM
which
includes
the User
Manual
Phone Cord
X 2
Ether
(CAT5
UTP)
Cable
Power
Adapter

2
Front Panel
Power Solid indicates a connection to a good power source.
Prov./Alm A blinking light indicates DVG-5402SP is attempting to
connect with the Provisioning server. Once the service
connects, the LED will turn off. The LED will light solid red
if the self-test or boot-up fails.
Register The Register LED will turn on when DVG-5402SP is
connected to a VoIP service provider. The LED will turn
off if not connected to a service provider.
WAN When a connection is established the 10 or 100 LED will
light up solid. The LED will blink to indicate activity. If the
10 or 100 LED does not light up when a cable is
connected, verify the cable connections and make sure
your devices are powered on.
LAN When a connection is established the 10 or 100 LED will
light up solid on the appropriate port. The LEDs will blink
to indicate activity. If the 10 or 100 LED does not light up
when a cable is connected, verify the cable connections
and make sure your devices are powered on.
Phone This LED displays the VoIP status and Hook activity on
the phone port that is used to connect your normal
telephone(s). If a phone connected to a phone port is off
hook or in use, this LED will light solid. When a phone is
ringing, the indicator will blink.
Line Light on means the line is in use (off-hook).
Hardware Overview

3
Rear Panel
1. Line: Connect to your original telephone line on the wall jack with
RJ-11 cable.
2. Phone Port (1-2): Connect to your phones using standard phone
cabling (RJ-11).
3. LAN: Connect to your Ethernet enabled computers using Ethernet
cabling.
4. WAN: Connect to your broadband modem using an Ethernet cable.
5. Power Receptor: Receptor for the provided power adapter.
6. Ground: A conducting connection with the earth. Connect with the
ground so as to make the earth a part of an electrical circuit using
metal wire.
Hardware Overview (continued)

4
A. Insert one end of the Ethernet cable into the Ethernet (LAN) port on
the back panel of the DVG-5402SP and the other end of the cable to
an Ethernet Adapter or available Ethernet port on your computer.
B. Insert one end of the Ethernet cable into the WAN port on the back of
the DVG-5402SP and the other into your cable/DSL modem or the
LAN port of your router.
C. Insert a telephone cable into the Phone port, and then connect the
cable to your telephone.
Installing the Hardware

5
D. Insert your original telephone line on the wall jack (PSTN) into the
Line port.
E. Connect the power adapter to the power input at the back panel of
the DVG-5402SP and then plug the other end of the power adapter
to a wall outlet or power strip. On the front of the device, the Power
LED will turn On to indicate proper operation.
F. Check the LED display on the front of the VoIP Router to confirm that
the connections have been made.
Installing the Hardware (continued)

6
After the installations are completed, your network should look similar to
the diagram below.
Hardware configuration is complete! If your VoIP service is already activated, you
can make phone calls now.
Installing the Hardware (continued)

7
Configuration
To access the web-based configuration utility, open a web browser such
as Internet Explorer and enter the IP address of the DVG-5402SP.
Open your Web browser and
type http://192.168.8.254 into
the URL address box. Press
the Enter or Return Key.
Click Login to enter Web Site.
Click Setup Wizard.

8
Configuration (continued)
The username of ADMIN and USER
have been defined and locked by
default. It is highly recommended to
create a login password to keep
your router secure.
Enter a NTP server or use the
default server.
Click Next.
Click Next.
Click Next.

9
Configuration (continued)
Select your Internet connection type:
DHCP – Most Cable ISPs or if you
are connecting the DVG-5402SP
behind a router.
Static IP – Select if your ISP
supplied you with your IP settings.
PPPoE – Most DSL ISPs.
PPTP – Select if required by your
ISP.
BigPond – For Australia only.
Select Manual to manually enter IP
address of DNS or select Auto if
DNS is assigned by ISP.
Click Next.
Click Next.
Register to the SIP Proxy Server
by clicking Enable support of SIP
Proxy Server. Enter Proxy
Server IP/Domain and Port.
The Outbound Proxy Support is
optional. To register, please click
on the Outbound Proxy Support
check box and enter Outbound
Proxy IP/Domain and Port in it.
Registration by phone line: enter
Number, User ID/Account and
Password supplied by your ITSP.
Click on the Register check box to
register to Proxy Server.

10
Configuration (continued)
Setup is finished. Check the
summary of your settings. To
make new settings effective, you
must click on the Restart button
to reboot the DVG-5402SP.
Click Restart.