D-Link DSL-G604T User manual

©2007 D-Link Australia Pty Ltd. All rights reserved. Trademarks or registered trademarks are the property of their
respective holders. Software and specifications subject to change without notice.
DSL-G604T ADSL Modem Router.
Before You Begin
1. If you purchased this Router to share your high-speed Internet connection with other
computers, you must have an established Internet account from an Internet Service Provider
(ISP).
2. It is best to use the same computer that is connected to your ISP for configuring the DSL-
G604T ADSL Modem Router. The DSL-G604T acts as a DHCP server and will assign all the
necessary IP address information on your network. See the Appendix for setting each
network adapter to automatically obtain an IP address.
Check Your Package Contents
If any of the above items are missing, please contact your reseller.
This product can be setup using
any current web browser, i.e.,
InternetExplorer6orNetscape
Navigator 6.2.3.
Using a power adapter with
a different voltage rating will
damage and void the
warranty for this product.
DSL-G604T Generation II
Wireless ADSL2+ Modem Route
r
CD-ROM with Click’n Connect Utility and
Product Documentation
Wireless Antenna
Telephone Cable (RJ-11)
CAT 5 UTP Ethernet Cable (RJ-45)
12V 1.25A
Power Adapter
DSL-G604T
A
DSL Modem Route
r

2
Connecting the Router to your
Computer
1. First, connect the power adapter to the power input at the back
panel of the DSL-G604T and then plug the other end of the
power adapter to a wall outlet or power strip. On the front of
the device, the Power LED will turn ON to indicate proper
operation.
2. Insert one end of the Ethernet cable into an Ethernet port on
the back panel of the DSL-G604T and the other end of the
cable to an Ethernet Adapter or available Ethernet port on your
computer.
3. Insert the telephone cable included with the Router into the
ADSL port, and then connect the cable to your telephone line.
(Line must be activated for ADSL use)
4. Check the LED display on the front of the Router to confirm
that the connections have been made. (This will be shown with
solid lights for the corresponding port)
ADSL Port
Connect to
your ADSL
p
hone line
Antenna
Post
Connect
antenna here
Ethernet Ports
Connect to
Ethernet cable
Power Input
Connect to
p
ower ada
p
ter

3
Configuring the Router via the
D-Link Click’n Connect Utility
Insert the CD-ROM into your PCs CD Drive. The Click’n Connect utility should
appear automatically. If it does not appear, explore your CD-ROM drive within
Windows, and double-click on the file “dslutility.exe” to start the utility
manually.
You can select one of five options:
1. User Manual: This option will open up the DSL-G604T user manual.
You will need Adobe Acrobat Reader installed to view the manual.
2. Quick Install Guide: This option will show you a software-based version
of this Quick Install Guide
3. Install Acrobat Reader: Selecting this option will install Adobe Acrobat
Reader onto your PC.
4. Technical Support: Selecting this option will link you to D-Link
Australia/New Zealand Technical Support online.
5. Start Installation: This will commence the installation of the DSL-
G604T.

4
Configuring the Router via the
D-Link Click’n Connect Utility
The Click’n Connect utility will guide you through the installation process step-
by-step. Follow the on-screen instructions, then proceed to the next step.
Step 1 - Power Up the Device
Connect the Power Adapter from the wall socket to the DSL-G604T. Wait for the
Status LED to blink before proceeding onto the next step.
Follow the on-
screen
instructions,
then Click
Next to
continue

5
Configuring the Router via the
D-Link Click’n Connect Utility
The Click’n Connect utility will guide you through the installation process step-
by-step. Follow the on-screen instructions, then proceed to the next step.
Step 2 – Connect the Device to your Computer
Connect the Ethernet cable from the computer to one of the LAN ports
(numbered 1 to 4) on the DSL-G604T now. Wait for the LAN Link LED for the
corresponding LAN port number to flash, then click on Next to continue to Step
3.
Follow the on-
screen
instructions,
then Click
Next to
continue

6
Configuring the Router via the
D-Link Click’n Connect Utility
The Click’n Connect utility will guide you through the installation process step-
by-step. Follow the on-screen instructions, then proceed to the next step.
Step 3 – Connect the Device to the ADSL Line
Connect your ADSL telephone line from the wall socket to the DSL-G604T
ADSL socket. Please note that if you are using an ADSL Splitter/Filter, you will
need to connect the telephone line from the DSL socket on the filter to the DSL-
G604T ADSL socket.
Once you have completed this, wait for the ADSL LED to light up, and click on
Next to continue to Step 4.
Follow the on-
screen
instructions,
then Click
Next to
continue

7
Configuring the Router via the
D-Link Click’n Connect Utility
The Click’n Connect utility will guide you through the installation process step-
by-step. Follow the on-screen instructions, then proceed to the next step.
Step 4 – Checking Device Connectivity
The Click’n Connect utility will now check the DSL-G604T to make sure it has
been connected correctly. Once it has successfully detected your modem, it will
proceed to the next step automatically.
At this point, you may want to prepare your ADSL account information that is
provided to you by your Internet Service Provider (ISP) as you will require it
shortly.

8
Configuring the Router via the
D-Link Click’n Connect Utility
The Click’n Connect utility will guide you through the installation process step-
by-step. Follow the on-screen instructions, then proceed to the next step.
Step 5 – ISP Configuration
You will now be prompted to select your Country as well as your Internet
Service Provider (ISP). If your ISP is not listed for your country, select Other
and enter the details that are relevant to your ISP.
Once you have completed this step, click on Next to continue onto Step 6.
Click Next to
continue
Select your
ISP
Select your
Country

9
Configuring the Router via the
D-Link Click’n Connect Utility
The Click’n Connect utility will guide you through the installation process step-
by-step. Follow the on-screen instructions, then proceed to the next step.
Step 6 – Account Configuration
At this step, you will be required to enter your ADSL account Username, as
provided by your ISP. You will also be required to enter your ADSL account
Password, then reenter the password in the Confirm Password box.
Please note, different ISP’s use different Usernames. Some use the first part of
your email address while some ISP’s use part or all of your email address. If
you are unsure as to which one your ISP uses, please confirm this with your
ISP.
Once you have completed this step, click on Next to continue onto Step 7.
Enter your ISP Username
Enter your ISP Password
Re-Enter
y
our ISP Password
Click Next to
continue

10
Configuring the Router via the
D-Link Click’n Connect Utility
The Click’n Connect utility will guide you through the installation process step-
by-step. Follow the on-screen instructions, then proceed to the next step.
Step 7 – Set Wireless Connection
You will now be asked if you would like to enable your Wireless Radio. The
wireless radio is what the router uses to provide wireless networking
functionality to your wireless computers. If you would like to turn the radio on,
select Enabled to turn it on, otherwise select Disabled to turn the radio off.
You can turn the radio on or off at a later date by referring to your User Manual.
Once you have completed this step, click Next to continue. If you Enabled
your wireless radio, proceed to step 7A on Page 10. If you Disabled your
wireless radio, proceed to Step 8 on Page 11.
Select your
Wireless Radio
Preference
Click Next to
continue

11
Configuring the Router via the
D-Link Click’n Connect Utility
The Click’n Connect utility will guide you through the installation process step-
by-step. Follow the on-screen instructions, then proceed to the next step.
This section is only relevant if you enabled the Wireless Radio on your
DSL-G604T Router at Step 7. If you disabled the Wireless Radio, please
proceed to page 11.
Step 7A – Set Wireless Connection
You will now be asked to set security to your wireless network. Type in your
desired SSID name, select a Channel, and set your preferred Encryption
settings for your wireless network. Please refer to your User Manual for more
information.
Important Note: You are strongly advised to enable Encryption on your
wireless network, as this will deter hackers from gaining access to your
network.
Enter your
SSID Name
Select your Channel
Select your
Encryption
Preferences
Click Next to
continue

12
Configuring the Router via the
D-Link Click’n Connect Utility
The Click’n Connect utility will guide you through the installation process step-
by-step. Follow the on-screen instructions, then proceed to the next step.
Step 8 – Completing Setup
The Click’n Connect Utility will now save the settings you have entered to the
DSL-G604T modem, and verify that you have entered your account details
correctly to ensure an Internet connection can be established.
If you receive an error message, please review all the information that you have
entered in very carefully, and try again.
Click Next to
continue

13
Configuring the Router via the
D-Link Click’n Connect Utility
The Click’n Connect utility will guide you through the installation
process step-by-step. Follow the on-screen instructions, then proceed
to the next step.
Step 9 – Setup Complete
If you have arrived at this screen, this means that your Internet
connection has been successfully established and all the details that
you have entered are correct.
Click Finish to
close the Click’n
Connect Utility

14
Configuring the Router via the
Web Interface
Now it is time to configure the Router. Enter 10.1.1.1 into the URL
address box.
The login dialog appears:
Open your Web browser and
type http://10.1.1.1 into the
URL address box. Press Enter or
Return.
When you first log in, your Login
Name is admin and your
password is also admin. These
may be changed later.

15
Configuring the Router via the
Web Interface
Once you have logged in, the Home directory tab is prominent with the setup
Wizard window displayed. Most users will be able to use the setup wizard to
establish the ADSL connection to your ADSL Internet Service Provider (ISP). To
begin using the setup wizard, click on the Run Wizard button in the middle of
the web page.
A pop-up window will appear. This pop-up window is the Setup Wizard. The
Setup Wizard procedure consists of four general steps:
1. Choose your time zone.
2. Set Internet connection.
3. Set wireless configuration.
4. Save and restart.
When you setup the Internet connection, you will need to enter the information
provided to you from your ISP. The type of information you need depends on
the type of connection you are setting up.
Click the Run Wizard button.

16
Configuring the Router via the
Web Interface
The first Setup Wizard window lists a summary of the steps required to
complete the setup. Click the Next button to begin setup.
Click
the Next button.

17
Configuring the Router via the
Web Interface
Configure the time zone used for the Router’s system clock. Select the
appropriate time zone setting for your location. Click Next to continue.
Next you will set the Internet connection type for the WAN interface. Click the
Next button.
Click the Next button.
Select the time zone you are
located in.

18
Configuring the Router via the
Web Interface
Configure the Internet connection type for the WAN interface. Your ISP has
given this information to you. If you do not know what type of connection to
use, exit the Setup Wizard and contact your ISP for the information. The Setup
Wizard window that appears when you click the Next button depends on what
connection type you select. The connection types available are PPPoE/PPPoA ,
Dynamic IP Address, Static IP Address, and Bridge Mode. Follow the instructions
below for the type of connection you are using.
Select the Connection Type
used for your ADSL service. Click the Next button.

19
Configuring the Router via the
Web Interface
PPPoE / PPPoA Connection
If you selected the PPPoE/PPPoA connection type in the previous window, you
will see the Setup Wizard window pictured here. Type in the Username and
Password used to identify and verify your account to the ISP. If you have been
instructed to change the VPI number and VCI number, type in the new values.
Select the Connection Type used for encapsulation specific to your service.
Click Next to go to the Set Wireless LAN Connection window.
Select the Connection
Type as instructed by
your ISP account. Click the Next button.
Type the Username
and Password for
your ISP account.
Change the VPI and
VCI numbers as
instructed by your ISP.
Type the new values in
the spaces provided
here.

20
Configuring the Router via the
Web Interface
Wireless LAN Connection
Configure the SSID and Channel for the Wireless LAN. You may also configure
either WEP or WPA security settings at this time or configure them later using
the web manager. Select None to configure either WEP or WPA later. To disable
the wireless access point, click the Enable AP option box to remove the green
check mark. Click Next to continue to the final menu.
Click
the Next button.
Enter the SSID name
and Channel number
for the Wireless LAN.
Uncheck this box to
disable the wireless
AP.
Choose None if you
neither want to
configure WEP nor WPA
lat this time.