D-Link DCS-7513 User manual

This document will guide you through
the basic installation process for your new
D-Link Network Camera.
DCS-7513
Documentation also available
on CD and via the D-Link
Website
Quick Installation Guide
Full HD WDR Day & Night Outdoor Network Camera

D-Link DCS-7513 Quick Install Guide
2
Quick Installation Guide
This installation guide provides basic instructions for installing the DCS-7513 on your network.
For additional information about how to use the camera, please see the User Manual which is
available on the CD included in this package or from the D-Link support website.
Installation Steps
1. Verify the package contents against the list below.
2. Hardware Overview
3. SD Card Installation
4. Hardware Installation
5. Conguration (Setup Wizard)
1. Package Contents
DCS-7513 Full HD WDR Day & Night Outdoor Network Camera
Mounting Bracket and Hardware
CAT5 Ethernet Cable
CD-ROM with User Manual and Software
Mounting Plate
Alignment Sticker
Quick Installation Guide
If any of the above items are missing, please contact your reseller.
Safety Notice:
Installation and servicing should be done by certied technicians to conform to all local codes
and prevent voiding your warranty.

D-Link DCS-7513 Quick Install Guide
3
2. Hardware Overview
Power Connector
Connects to a 12 V DC power adapter
(not included).
24 V Power Connector
Connects to 24 V AC power.
Reset Button
Press for 10 seconds to reset the camera
back to the factory default settings.
BNC
Analog video output.
Ethernet Jack
RJ-45 connector for Ethernet which
can also be used to power the camera
using Power over Ethernet (PoE).
Audio In
Connects to a microphone.
DI/DO Wiring, 12 V DC output
I/O connectors for external devices.
Install the SD Card
Push the SD card into the card
slot with the gold contacts
directed towards the base of
the camera. To eject the SD
card, push the SD card into the
slot and release. The SD card
will spring out.
3. SD Card Installation
Disassemble the Camera
Open the camera by
loosening the two screws.
Audio Out
Connects to speakers.
3
1
4
2

D-Link DCS-7513 Quick Install Guide
4
4. Mounting Instructions
Mounting Installation
Refer to the User Manual for detailed instructions regarding the installation and mounting of
the camera using a mounting bracket.
Figure 2.1
Figure 2.3
Figure 2.2
Figure 2.4

D-Link DCS-7513 Quick Install Guide 5
Connection with a PoE Switch
If you are using a PoE switch, connect the camera to the switch using an Ethernet cable, which
will provide transmission of both power and data over a single cable.
General Connection Using 24 V AC Power Wiring
1. Connect the network camera to your network using an Ethernet cable.
2. Connect the supplied power cable from the camera to a power source such as your
building's emergency power.
General Connection Using a 12 V DC Power Adapter
1. Connect the network camera to your network using an Ethernet cable.
2. Connect a compatible 12 V power adapter (not included) from the camera to a power outlet.

D-Link DCS-7513 Quick Install Guide
6
5. Conguration (Setup Wizard)
Click Setup Wizard to begin the installation.
Insert the DCS-7513 CD into your computer's CD-ROM drive to begin the installation. If the Autorun
function on your computer is disabled, or if the D-Link Launcher fails to start automatically, click
the Start button and in the box type D:\autorun.exe, where D: represents the drive letter of your
CD-ROM drive.
After clicking Setup Wizard, the following window will open.
Click Next to continue.
Click Yes to accept the License Agreement.
Click Finish to complete the installation.
To start the installation process, click Next.
Note: The installation may take several minutes to nish.

D-Link DCS-7513 Quick Install Guide 7
Click on the D-Link Setup Wizard SE icon that was created
in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Take a moment to conrm your settings and click Restart.
Select DHCP if your camera automatically obtains an IP
address from a DHCP server such as a router. Select Static
IP if you want to manually enter the IP settings for the
camera.
Click Next to continue.
Enter the Admin ID and password. When logging in for the
rst time, the default Admin ID is admin with the password
left blank.
Click Next to continue.
The Setup Wizard will appear and display the MAC address
and IP address of your camera(s). If you have a DHCP server
on your network, a valid IP Address will be displayed. If your
network does not use a DHCP server, the network camera's
default static IP 192.168.0.20 will be displayed.
Click the Wizard button to continue.

D-Link DCS-7513 Quick Install Guide
8
Click on the D-Link Setup Wizard SE icon that was
created in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Viewing Camera via Web Browser
This section shows your camera’s live video. You can select
your video prole and view or operate the camera. For
additional information about web conguration, please
refer to the user manual included on the CD-ROM or the
D-Link website.
Select admin as the username and leave the password
blank. Click OK to continue.
Select the camera and click the Link button to access the
web conguration.
The Setup Wizard will automatically open your web browser
to the IP address of the camera.

D-Link DCS-7513 Quick Install Guide 9
Notes

D-Link DCS-7513 Quick Install Guide
10
Notes