D-Link DCS 6210 User manual

This document will guide you through the basic
installation process for your new D-Link Network
Camera.
DCS-6210
Quick Install Guide
Full HD Mini Fixed-Dome Network Camera
Quick Installation Guide

D-Link DCS-6210 Quick Install Guide
2
DCS-6210 Quick Install Guide
This installation guide provides basic instructions for installing the DCS-6210 Full HD Mini
Fixed-Dome Network Camera on your network. For additional information about how to
use the camera, please see the User’s Manual, which is available on the CD included in this
package or on the D-Link support website.
Installation Steps
1. Verify the package contents against the list below.
2. Hardware Overview.
3. SD Card Installation.
4. Hardware Installation.
5. Conguration with Wizard.
6. Adjusting the 3-axis gimbal.
1. Package Contents
Full HD Mini Fixed-Dome Network Camera
Power Adaptor
CAT5 Ethernet Cable
Quick Install Guide
Installation CD with D-ViewCam™
Mounting Kit with Security Wrench
If any of the above items are missing, please contact your reseller.
Safety Notice: Installation and servicing should be done by certied technicians so as to conform
to all local codes and prevent voiding your warranty.

D-Link DCS-6210 Quick Install Guide 3
2. Hardware Overview
SD/SDHC Card Slot
SD/SDHC card for storing
recorded images and video
Power Connector
Connects to 12V DC power
Ethernet Jack
RJ-45 connector for Ethernet
which can also be used to
power the camera using
Power over Ethernet (PoE)
Install the SD Card
Push the SD card into the camera with the
gold contacts oriented towards the base of
the camera. To eject the SD card, push the
SD card into the slot.
3. SD Card Installation
Disassemble the Camera
Open the camera enclosure by loosening
the 3 screws. Lift the dome o the base of
the camera.
LED
Power and network
indicator
Reset
Press and hold this
button for 10 seconds
to reset the camera
SD

D-Link DCS-6210 Quick Install Guide
4
4. Hardware Installation
Mounting Installation
Please see the User Manual for detailed instructions regarding installation and mounting of
the camera.
Figure 4.1 Figure 4.2
Figure 4.3 Figure 4.4
Figure 4.5

D-Link DCS-6210 Quick Install Guide 5
Connection with a PoE Switch
If you are using a PoE switch, connect the camera to the switch via an Ethernet cable, which
will provide transmission of both power and data over a single cable.
General Connection Using 12V DC Power Adapter
1. Connect the network camera to a switch via an Ethernet cable.
2. Connect the supplied power cable from the camera to a power outlet.

D-Link DCS-6210 Quick Install Guide
6
5. Conguration with Wizard
Click Setup Wizard to begin the installation.
Insert the DCS-6210 CD into your computer's CD-ROM drive to begin the installation. If the Autorun
function on your computer is disabled, or if the D-Link Launcher fails to start automatically, click
Start > Run. Type D:\autorun.exe, where D: represents the drive letter of your CD-ROM drive.
After clicking Setup Wizard, the following window will open.
Click Next to continue.
Click Yes to accept the License Agreement.
Click Finish to complete the installation.
To start the installation process, click Next.
Note: The installation may take several minutes to nish.

D-Link DCS-6210 Quick Install Guide 7
Click on the D-Link Setup Wizard SE icon that was created
in your Windows Start menu.
Start > Programs > D-Link > Setup Wizard SE
Take a moment to conrm your settings and click Restart.
Select DHCP if your camera obtains an IP address
automatically when it boots up. Select Static IP if the
camera will use the same IP address each time it is started.
Click Next to proceed to the next page.
Enter the Admin ID and password. When logging in for the
rst time, the default Admin ID is admin with the password
left blank.
Click Next to proceed to the next page.
The Setup Wizard will appear and display the MAC address
and IP address of your camera(s). If you have a DHCP server
on your network, a valid IP address will be displayed. If your
network does not use a DHCP server, the network camera's
default static IP (192.168.0.20) will be displayed.
Click the Wizard button to continue.

D-Link DCS-6210 Quick Install Guide
8
Click on the D-Link Setup Wizard SE icon that was created
in your Windows Start menu.
Start > Programs > D-Link > Setup Wizard SE
Viewing Camera via Web Browser
This section shows your camera’s live video. You can select
your video prole and view or operate the camera. For
additional information about web conguration, please
refer to the user manual included on the CD-ROM or the
D-Link website.
Enter admin as the default username and leave the
password blank. Click OK to continue.
Select the camera and click the Link button to access the
web conguration.
The Setup Wizard will automatically open your web
browser to the IP address of the camera.

D-Link DCS-6210 Quick Install Guide 9
Adjust the Viewing Angle of the 3-Axis Gimbal
Turn the lens module left and right until the desired
position is achieved.
Turn the lens up and down until the desired position
is achieved.
Turn the lens to adjust the camera’s image until the
desired orientation is achieved.
6. Adjusting the 3-Axis Gimbal

D-Link DCS-6210 Quick Install Guide
10
Notes