D-Link SECURICAM DCS-7110 User manual

This document will guide you through the basic installation
process for your new D-Link Network Camera.
DCS-7110
Quick Installation Guide
Full HD Day & Night Network Camera

D-Link DCS-7110 Quick Installation Guide
2
This installation guide provides basic instructions for installing the DCS-7110
Network Camera on your network. For additional information about how to
use the camera, please see the User Manual which is available on the CD
included in this package or from the D-Link website.
Installation Steps
1. Verify the package contents against the list below
2. Hardware Overview
3. Conguration
4. Mounting the Camera
Package Contents
• DCS-7110 Full HD Day & Night Network Camera
• Mounting Kit
• User Manual and Software on CD-ROM
• CAT5 Ethernet Cable
• Quick Installation Guide
• Hex Key
If any of the above items are missing, please contact your reseller.
Installation

D-Link DCS-7110 Quick Installation Guide 3
Infrared LEDs
IR LEDs Illuminate the
camera's eld of view.
DI/DO Connectors
DI/DO connectors provide a physical interface to send
and receive digital signals to and from a variety of
external devices.
DC Power Connector
Connects a 12 V power adapter (not included) to the camera.
Ethernet (PoE)
The RJ-45 connector is for Ethernet and can also be
used to power the camera using PoE.
IR-Cut Removable (ICR) Sensor
IR-Cut Removable sensor judges
lighting conditions and switches
from day mode to night mode
accordingly.
Sunshield
Adjustable sunshield
protects the camera
sensor from direct
sunlight.
24 V Power Connector
Connects to 24V AC power.
Hardware Overview

D-Link DCS-7110 Quick Installation Guide
4
Reset Button
After removing the weatherproof cover,
use a paperclip or similar tool to press and
hold the recessed button for 10 seconds
to reset the camera back to the factory
default settings.
Hardware Overview

D-Link DCS-7110 Quick Installation Guide
5
Note: Once the camera is receiving power, the LED will turn red. When the device has
obtained an IP address and is accessible, the LED will turn green.
Basic Connection (without PoE)
1. Connect the camera to your switch or router via Ethernet cable.
2. Connect the power cable from the camera to a compatible 12V power adapter (not included).
3. Connect the power adapter to a power outlet.
Power over Ethernet (PoE) Connection
If using a PoE switch or router, connect the network camera via Ethernet cable. PoE will
transmit both power and data over a single cable.
Cable Connections

D-Link DCS-7110 Quick Installation Guide
6
To prevent the camera’s wire connectors from being damaged by water or other elements:
1. When connecting the camera, the unsheathed part of the wire connectors must either be
sealed or enclosed in a junction box.
2. The unsheathed part of the wire connectors should be positioned at a downward-facing
angle when they extend out of the rear of the camera, not upward.
The unsheathed part of the wire connectors must either be
sealed or enclosed in a junction box.

D-Link DCS-7110 Quick Installation Guide
7
Insert the DCS-7110 CD into your computer's CD-ROM drive to begin the installation. If
the Autorun function on your computer is disabled, or if the D-Link Launcher fails to start
automatically, click the Start button and type D:\autorun.exe, where D: represents the drive
letter of your CD-ROM drive.
Click Setup Wizard to begin the installation.
You will see the Welcome screen for the Setup Wizard.
Click Next to continue.
Click Yes to accept the License Agreement.
Select the location to install the Wizard and click Next to
continue.
Note: The installation may take several minutes to nish.
Conguration

D-Link DCS-7110 Quick Installation Guide
8
Click Finish to complete the installation.
Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Enter the Admin ID and password. When logging in for
the rst time, the default Admin ID is admin with the
password left blank.
Click Next to continue.
The Setup Wizard will appear and display the MAC address and IP address of your camera(s). If
you have a DHCP server on your network, a valid IP Address will be displayed. If your network
does not use a DHCP server, the network camera's default static IP 192.168.0.20 will be
displayed.
Click the Wizard button to continue.

D-Link DCS-7110 Quick Installation Guide
9
Take a moment to conrm your settings and click Restart.
Select DHCP if your camera automatically obtains an IP
address from a DHCP server such as a router. Select Static
IP if you want to manually enter the IP settings for the
camera.
Click Next to continue.

D-Link DCS-7110 Quick Installation Guide
10
Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Enter admin as the default username and leave the
password blank. Click OK to continue.
Select the camera and click the Link button to access
the web conguration.
The Setup Wizard will automatically open your web
browser to the IP address of the camera.
Viewing Camera via Web Browser