D-Link DES-7206 User manual

DES-7200 Series
Quick Installation Guide

DES-7200 Series Quick Installation Guide
Revision No.: V1.1
Date:2007/8/16
Copyright statement
All rights reserved.
D-Link Corporation reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any
means, without the prior written consent of D-Link Corporation is prohibited.
Exemption statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please
obtain the latest information through the D-Link Corporation website. D-Link Corporation endeavors to ensure content
accuracy and will not shoulder any responsibility for losses and damages caused due to content omissions,
inaccuracies or errors.

Contents
Product Overview....................................................................................................................................3
Safety Precautions for Removing ...........................................................................................................3
Preparation Before Installation................................................................................................................4
Temperature and Humidity Requirements ....................................................................................4
Static Discharge Damage Prevention...........................................................................................4
System Grounding Requirements.................................................................................................5
Power Requirements ....................................................................................................................5
Requirements of Installation Tools................................................................................................6
Installation Site Requirements ................................................................................................................7
Requirements for Rack Mounting .................................................................................................7
Ventilation Requirements..............................................................................................................7
Mounting the DES-7210/7206 into the Cabinet ............................................................................8
Installing the Fan Tray...................................................................................................................8
Installing the Power Supply...........................................................................................................9
Installing the Handle ...................................................................................................................10
Installing the Cabling Rack of the DES-7210.............................................................................. 11
Installing the Air Filter of the DES-7210...................................................................................... 11
Connecting the System Ground..................................................................................................12
Connecting the DC Power Supply to the Power Module............................................................12
Connecting the AC Power Supply to the Power Module ............................................................13
Connecting the Cable of the Management Module ....................................................................14
Removing Boards from the DES-7210/7206 ..............................................................................14
Installing Boards on the DES-7210/7206....................................................................................15
Installation Check........................................................................................................................15
Unpacking Inspection Requirements ....................................................................................................16
Checking Goods .........................................................................................................................16
i

DES-7200 Series Quick Installation Guide
Product Overview
D-Link Corporation introduces high-density multi-service IPv6 core router switch DES-7200
by sparing great efforts, after the release of the multi-service 10,000M core router switch
DES-7200 being applicable to the backbone Ethernet. DES-7200, as a multi-service IPv6
10,000M core router switch of the new generation, provides powerful defense ability while
ensuring high performance and large capacity. It also boasts the ability of service addition
and expansion on demand, thus satisfying the design requirements of equal emphasis on
service and performance. Currently, two models are available, DES-7206 and DES-7210,
which offer ten vertical slots and six horizontal slots respectively.
The DES-7210 series multi-service Ipv6 10,000M core router switch provides users with
high-speed non-blocking data switching. With powerful switching and routing functions and
secure intelligent technologies, it can be used together with various series of D-Link
switches to provide users with complete end-to-end solutions. It is ideal for large-scale
network core backbone and heavy traffic node switch. By expanding with high-performance
multi-service cards, the DES-7200 series switches support policy routing and IPV6, and
satisfies customers’ flexible and complex application requirements.
Applications:
Core layers of such enterprise networks of educational, financial and governmental
organizations
Running environment that needs powerful routing function and carrier-class security &
reliability
High-layer switching of enterprise networks with high bandwidth and 10G needs
Enterprise environment that needs to provide high QoS assurance for various
applications
Safety Precautions for Removing
The DES-7210/7206 is large and heavy. When you handle them, please pay attention to the
following requirement:
Avoid moving the equipment frequently.
At least two people are needed to move the equipment. Do not attempt to move the
equipment by one person only.
Keep balanced in moving the equipment, and avoid injuring your leg and feet or
spraining your waist.
Turn off all power supplies and unplug all power cables before you can remove the
equipment.
First remove all the line cards, fan tray, and power module from the chassis before you
can move the DES-7210/7206 by using the handles on both sides, to avoid any
damage.
3

DES-7200 Series Quick Installation Guide
Correctly Moving the DES-7210 and DES-7206
Warning
Do not move the equipment by grasping the panel, power supply handle,
ventilation holes of the chassis, as they are not designed to bear the
weight of the entire equipment. Failing to do so may cause damage or
even injure yourself.
Preparation Before Installation
Temperature and Humidity Requirements
To ensure the normal working and a prolonged useful life of the DES-7210/7206, appropriate
temperature and humidity must be maintained in the equipment room.
If the equipment room has temperature and humidity that do not meet the requirements for a
long time, the equipment may be damaged.
Temperature and Humidity Requirements of the DES-7210/7206
Temperature Relative Humidity
Long-term condition Short-term condition Long-term condition Short-term condition
0ºC-45ºC 0ºC-45ºC 40%-65% 10%-90%
Note
1. The ambient temperature and humidity are measured at the point that is
1.5m above the floor and 0.4m before the equipment when there is no
protective plate in front or back of the equipment rack.
2. The short-term working condition applies where the continuous working
period does not exceed 48 hours and the accumulative total period within
a year does not exceed 15 days.
Static Discharge Damage Prevention
To prevent damage from static electricity, you must pay attention to the following:
1. Proper grounding of the equipment and floor
2. Dust prevention measures are taken in the room.
4

DES-7200 Series Quick Installation Guide
3. An appropriate humidity is maintained.
4. Always wear an anti-static wrist strap when you touch any circuit board.
5. Try to hold a circuit board by its edges. Do not touch any components or the PCB.
6. Do not let any clothes touch a circuit board. An antistatic wrist strap can only prevent
static electricity from human damaging the circuit board, but cannot prevent any static
electricity on clothes.
System Grounding Requirements
A good grounding system is the basis for the stable and reliable operation of the
DES-7210/7206. It is the chief condition to prevent lightning stroke and resist interference.
Please carefully check the grounding conditions on the installation site according to the
grounding requirements, and perform grounding properly as needed.
Grounding of the DES-7210/7206
The system cables must ensure the normal working of the equipment. Before you connect
the cables, please carefully read the following precautions.
Power Requirements
When the DES-7210/7206 uses the AC power supply:
AC input voltage: 90Vac~264Vac, 47Hz~63Hz
Power: 1200W/2000W
When the DES-7210/7206 uses the DC power supply:
DC input voltage: DC - 36Vdc ~ -75Vdc
Power: 1200W/2000W
Please refer to following table to evaluate the total system requirement:
5

DES-7200 Series Quick Installation Guide
DES-7200 Series Modules Maximum Power Consumption (W)
7200-CM1 30
7200-CM2 30
7200-24G 75
7200-24 85
7200-48 100
7200-2XG 75
7200-24P 85+15.4*N (N indicates the PoE port being used, of
which the value is less than 24)
7200-48P 100+15.4*N (N indicates the PoE port being used, of
which the value is less than 48)
Note
The DES-7210/7206 provides 1+1 redundancy of power supply. You are
recommended to use multiple power supplies for the equipment to ensure
its continuous and stable working by avoiding the impact of unexpected
power failures on the equipment. However, you must note that the
redundancy power supplies must be of the same type; a mix of power
supplies is not allowed.
Requirements of Installation Tools
List of Installation Tools
Common tools Cross screwdriver, straight screwdriver, related electric and optical
cables
Bolts, diagonal pliers, straps
Special-purpose tools Anti-static tool
Meter Multimeter
6

DES-7200 Series Quick Installation Guide
Installation Site Requirements
The DES-7210/7206 must be used indoors. To ensure the normal working and a prolonged
useful file of the equipment, the installation site must meet the following requirements.
Requirements for Rack Mounting
If you plan to mount the DES-7210/7206 in a frame, you must verify that the frame meets the
following conditions:
Install the switch in an open cabinet as much as possible. If you install the switch inside
a closed cabinet, please make sure that the cabinet has a good ventilation and heat
dissipation system.
Make sure that the cabinet is firm enough to bear the weight of the DES-7210/7206 and
its installation accessories.
Make sure that the dimensions of the cabinet spare certain space for the installation of
the front, rear, left and right panels of the DES-7210/7206 for the sake of heat
dissipation.
The frame should be properly grounded.
Ventilation Requirements
Following figure shows the ventilation requirements of the DES-7210/7206. You must
ensure that sufficient spacing is reserved at the ventilation openings to ensure the normal
working of ventilation. After various cables have been connected, they should be arranged
into bundles or placed on the cabling rack, to avoid blocking the air inlets.
Ventilation of the DES-7210 and DES-7206
7

DES-7200 Series Quick Installation Guide
Mounting the DES-7210/7206 into the Cabinet
Verify the following before installation:
The cabinet has been fastened properly and various modules in the frame have been
installed. There should be no obstacles for installation in the frame and in the surrounding.
The equipment to be installed is ready, and has been moved to a place of easy handling and
close to the frame.
Simple Installation Steps:
1. Levelly lift the DES-7210/7206 by two people on both sides, and slowly move it to the
front of the frame.
2. Levelly lift the DES-7210/7206 to a position slightly higher than the tray or the slide rail
of the cabinet, put the equipment onto the tray or the slide rail, and push it into the
cabinet.
3. Fasten the DES-7210/7206 onto the cabinet with screws. There are fastening notches
on both the left and right of the front panel on the equipment frame. Use screws to
fasten them to the fastening bracket of the cabinet. After fastened, the equipment
should be stable and still in the cabinet.
Installing the Fan Tray
The DES-7210/7206 provides a ventilation system, 7210-FAN for DES-7210, and 7206-FAN
for DES-7206. Install the fan tray by performing the following steps:
1. Remove the blank panel of the fan tray by loosing the captive screws with a straight
screwdriver and the cross screws with a cross screwdriver.
2. Push the fan into the cabinet along the guide rail.
3. Tighten the captive screws with a straight screwdriver. Figure 3-1 and Figure 3-2 show
the installed fan tray.
Installing the Fan Tray of the DES-7210 and DES-7206
8

DES-7200 Series Quick Installation Guide
Installing the Power Supply
The DES-7210/7206 system provides AC and DC power, which can be installed in the same
way by performing the following steps:
1. Remove any blank panel of the power module by loosening the two cross screws with a
cross screwdriver, as shown in Figure 3-3 and 3-4.
Installing the Power Supply of the DES-7210 and DES-7206
2. Insert the power supply module into the cabinet along the guide rail, as shown in Figure
3-5 and Figure 3-6:
Installing the Power Supply of the DES-7210 and DES-7206
9

DES-7200 Series Quick Installation Guide
3. Tighten the screws on both sides of the power supply by using a straight screwdriver,
as shown in Figure 3-7 and Figure 3-8.
Installing the Power Supply of the DES-7210 and DES-7206
Installing the Handle
For easy handling of the system, the DES-7210/7206 chassis is provided with a handle,
which can be installed by performing the following steps:
1. Align the handle with the sunk hole on the fastening bar;
2. Tighten the cross M4 sunk screws provided with the unit, as shown in Figure 3-9 and
Figure 3-10.
Installing the Handle of the DES-7210 and DES-7206
10

DES-7200 Series Quick Installation Guide
Installing the Cabling Rack of the DES-7210
The cabling rack of the DES-7210 can be performed by performing the following steps:
1. Remove the blank panel of the tracing rack by loosing the captive screws with a straight
screwdriver and the cross screws with a cross screwdriver.
2. Install the panel of the tracing rack by tightening the two captive screws with a straight
screwdriver and the four cross screws with a cross screwdriver.
3. Fasten the cabling rack by using the cross M3 screws provided. (The cabling rack is
available in two sizes, and you can select the appropriate one)
Installing the Cabling Rack of the DES-7210
Installing the Air Filter of the DES-7210
Simply push the air filter of the DES-7210 into the cabinet along the guide rail.
Installing the Air Filter of the DES-7210
11

DES-7200 Series Quick Installation Guide
Note
You are recommended to install the air filter as the last step of the chassis
installation.
Connecting the System Ground
A working ground GND is installed on the back of DES-7210/7206. In order to protect the
system, the ground must be well treated. GND is directly connected to the ground bar or
ground pole of the equipment room.
Connection of grounding posts on the DES-7210/7206 back
Precautions
The sectional area of the grounding cable should be determined according to the
possible maximum current. Cables of good conductor should be used.
Do not use bare wire.
The grounding resistance for combined grounding should be less than 1Ω.
Simple Grounding Steps
1. Release the nut on the rear grounding post of the equipment.
2. Lock the terminal of the grounding cable to the grounding pole.
3. Tighten the nut.
4. Connect the related terminals according to the above steps and the wiring diagram.
Connecting the DC Power Supply to the Power
Module
Connect the related DC power cable according to the ID on the panel of the DC power
module and the location requirement. as shown in the following diagram.
12

DES-7200 Series Quick Installation Guide
Schematic Diagram for the Connection of the DC Power Cable
Precautions
Before connecting the power supply, you must verify that the external power supply
provided matches the power module installed of this equipment.
Before connecting the power cable, you must make sure that the switch of the power
module is at the OFF position.
The power cables of various colors must be connected to the appropriate wiring posts.
You must ensure that the power cables connected are in good contact.
Simple Connection Steps
1. Remove the protection cover of the DC wiring terminal.
2. Lock the power cable to the appropriate terminal according to the identification, and
tighten the pressing screw.
3. Put on the protection cover and tighten the screw.
4. Connect the other end of the power cable to the corresponding socket or connector.
Connecting the AC Power Supply to the Power
Module
Connect the related AC power cable according to the ID on the panel of the AC power
module and the location requirement, as shown in the following diagram.
13

DES-7200 Series Quick Installation Guide
Schematic Diagram for the Connection of the AC Power Cable
Precautions
Before connecting the power supply, you must verify that the external power supply
provided matches the power module installed of this equipment.
Before connecting the power cable, you must make sure that the switch of the power
module is at the OFF position.
The power cable with a standard 3-pin connector should be used for connection.
You must ensure that the power cables connected are in good contact.
Simple Connection Steps
1. Insert the plug of the power cable into the power module.
2. Connect the other end of the power cable to the corresponding socket or connector.
Connecting the Cable of the Management
Module
1. Connect the end of the Ethernet cable with the RJ45 connector to the Ethernet port of
the equipment management module (7210/7200-CM1), and the other end to the NM or
control terminal.
2. Connect the end of the standard DB9 serial cable with the RS-232 serial port to the
RS-232 serial port of the equipment management module, and the other end to the NM
or control terminal.
Note
The DES-7210/7206 system must have at least one management module
to work normally.
Removing Boards from the DES-7210/7206
1. Unplug all cables/fibers such as optical fibers and RJ45 twisted pairs from the panel.
2. Tighten two captive screws on the panel.
3. Draw out the board by holding the ejector with both hands, as shown in Figure 3-18 and
Figure 3-19.
14

DES-7200 Series Quick Installation Guide
Warning
1. Always wear an anti-static wrist strap before plugging/unplugging a
board.
2. Do not hold the edge of the PCB or collide the components on the
PCB.
Components of DES-7210 and DES-7206
Installing Boards on the DES-7210/7206
1. Remove the appropriate component card or blank panel according to 3.14.
2. Replace it with the appropriate card and insert into the guide rail.
3. Push the card into position by using the ejector, and tighten the two captive screws on
the card with a straight screwdriver.
Warning
1. Do not hold the edge of the PCB or collide the components on the
PCB.
2. When you plug/unplug a PCB module, use the ejector, instead of
forcedly.
Installation Check
Verify if the external power supply matches the distribution panel of the cabinet.
After the equipment is installed, check if the front/back cabinet doors can be closed.
Verify that the cabinet has been fastened completely, and does not move or tilt.
Verify that the equipment has been installed in the cabinet, and all the cables have
been fastened to the cabinet.
Verify that the optical fibers and twisted pairs match the interfaces.
Verify that the cables have been bound properly.
Verify that the power cables are in good contact and comply with the safety
requirements.
Verify that the power module has been fastened onto the equipment with the two
screws on the panel.
Turn on the power switch and verify that the power module can work normally.
15

DES-7200 Series Quick Installation Guide
Unpacking Inspection Requirements
Checking Goods
1. DES-7210/7206 chassis carton
Whether various panels of the equipment have been installed and adjusted properly
Documentation
2. DES-7210/7206 accessories carton
Whether the power module of the equipment is the required AC or DC module
Fan tray
Antistatic hand ring
Screwdriver
Power cable (for AC power configuration only)
Documentation
3. Module carton
It contains the modules, packing list and documentation of the DES-7210/7206.
Note
The above lists the items of a normal delivery, which may differ from the
actual delivery. All depend on the purchasing contract. Please check your
goods carefully against the packing list or purchasing contract. If you have
any questions or there are any errors, please contact your distributor.
16