D-Link DGS-3212SR User manual

DGS-3212SR
Command Line Interface Reference Manual
First Edition (August 2003)
………….

DGS-3212SR Switch CLI Reference
Wichtige Sicherheitshinweise
1. Bitte lesen Sie sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den spätern Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig-
oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung.
4. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden,
die vom Hersteller zugelassen sind.
5. Das Gerät is vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sichern Stand zu achten. Ein Kippen oder Fallen
könnte Verletzungen hervorrufen. Verwenden Sie nur sichere Standorte und beachten Sie
die Aufstellhinweise des Herstellers.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor Überhitzung schützt.
Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden.
8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.
9. Die Netzanschlußsteckdose muß aus Gründen der elektrischen Sicherheit einen
Schutzleiterkontakt haben.
10. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollete auch
nichts auf der Leitung abgestellt werden.
11. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten.
12. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz
trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden.
13. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät
gelangen. Dies könnte einen Brand bzw. Elektrischen Schlag auslösen.
14. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur
von authorisiertem Servicepersonal geöffnet werden.
15. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer
qualifizierten Servicestelle zu überprüfen:
16. Netzkabel oder Netzstecker sint beschädigt.
17. Flüssigkeit ist in das Gerät eingedrungen.
18. Das Gerät war Feuchtigkeit ausgesetzt.
19. Wenn das Gerät nicht der Bedienungsanleitung ensprechend funktioniert oder Sie mit Hilfe
dieser Anleitung keine Verbesserung erzielen.
20. Das Gerät ist gefallen und|oder das Gehäuse ist beschädigt.
21. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
22. Bei Reparaturen dürfen nur Orginalersatzteile bzw. den Orginalteilen entsprechende Teile
verwendet werden. Der Einsatz von ungeeigneten Ersatzteilen kann eine weitere
Beschädigung hervorrufen.
23. Wenden Sie sich mit allen Fragen die Service und Repartur betreffen an Ihren
Servicepartner. Somit stellen Sie die Betriebssicherheit des Gerätes sicher.
24. Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden, Für einen
Nennstrom bis 6A und einem Gerätegewicht grőßer 3kg ist eine Leitung nicht leichter als
H05VV-F, 3G, 0.75mm2 einzusetzen.
ii

DGS-3212SR Switch CLI Reference
Limited Warranty
WARRANTIES EXCLUSIVE
Hardware:
IF THE D-LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE,
THE CUSTOMER'S SOLE REMEDY SHALL BE, AT D-LINK'S OPTION,
REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND
REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY
OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. D-LINK NEITHER ASSUMES NOR AUTHORIZES ANY OTHER
PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION
WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF D-LINK'S
PRODUCTS
D-Link warrants each of its hardware products to be free from defects in workmanship and
materials under normal use and service for a period commencing on the date of purchase
from D-Link or its Authorized Reseller and extending for the length of time stipulated by
the Authorized Reseller or D-Link Branch Office nearest to the place of purchase.
This Warranty applies on the condition that the product Registration Card is filled out and
returned to a D-Link office within ninety (90) days of purchase. A list of D-Link offices is
provided at the back of this manual, together with a copy of the Registration Card.
If the product proves defective within the applicable warranty period, D-Link will provide
repair or replacement of the product. D-Link shall have the sole discretion whether to
repair or replace, and replacement product may be new or reconditioned. Replacement
product shall be of equivalent or better specifications, relative to the defective product, but
need not be identical. Any product or part repaired by D-Link pursuant to this warranty
shall have a warranty period of not less than 90 days, from date of such repair, irrespective
of any earlier expiration of original warranty period. When D-Link provides replacement,
then the defective product becomes the property of D-Link.
D-LINK SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING
AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE
PRODUCT DOES NOT EXIST OR WAS CAUSED BY THE CUSTOMER'S OR
ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR
TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE
BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE,
LIGHTNING OR OTHER HAZARD. Warranty service may be obtained by contacting a D-Link office within the applicable
warranty period, and requesting a Return Material Authorization (RMA) number. If a
Registration Card for the product in question has not been returned to D-Link, then a proof
of purchase (such as a copy of the dated purchase invoice) must be provided. If Purchaser's
circumstances require special handling of warranty correction, then at the time of
requesting RMA number, Purchaser may also propose special procedure as may be suitable
to the case.
LIMITATION OF LIABILITY
IN NO EVENT WILL D-LINK BE LIABLE FOR ANY DAMAGES, INCLUDING
LOSS OF DATA, LOSS OF PROFITS, COST OF COVER OR OTHER
INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES ARISING OUT
THE INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE OR
INTERRUPTION OF A D- LINK PRODUCT, HOWEVER CAUSED AND ON ANY
THEORY OF LIABILITY. THIS LIMITATION WILL APPLY EVEN IF D-LINK
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
After an RMA number is issued, the defective product must be packaged securely in the
original or other suitable shipping package to ensure that it will not be damaged in transit,
and the RMA number must be prominently marked on the outside of the package. The
package must be mailed or otherwise shipped to D-Link with all costs of
mailing|shipping|insurance prepaid. D-Link shall never be responsible for any software,
firmware, information, or memory data of Purchaser contained in, stored on, or integrated
with any product returned to D-Link pursuant to this warranty.
IF YOU PURCHASED A D-LINK PRODUCT IN THE UNITED STATES, SOME
STATES DO NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU. Any package returned to D-Link without an RMA number will be rejected and shipped
back to Purchaser at Purchaser's expense, and D-Link reserves the right in such a case to
levy a reasonable handling charge in addition mailing or shipping costs.
iii

DGS-3212SR Switch CLI Reference
D-Link Offices for Registration and Warranty Service
Software:
The product's Registration Card, provided at the back of this manual, must be sent to a
D-Link office. To obtain an RMA number for warranty service as to a hardware product,
or to obtain warranty service as to a software product, contact the D-Link office nearest
you. An address|telephone|fax|e-mail|Web site list of D-Link offices is provided in the
back of this manual.
Warranty service for software products may be obtained by contacting a D-Link office
within the applicable warranty period. A list of D-Link offices is provided at the back of
this manual, together with a copy of the Registration Card. If a Registration Card for the
product in question has not been returned to a D-Link office, then a proof of purchase (such
as a copy of the dated purchase invoice) must be provided when requesting warranty
service. The term "purchase" in this software warranty refers to the purchase transaction
and resulting license to use such software.
Trademarks
D-Link warrants that its software products will perform in substantial conformance with the
applicable product documentation provided by D-Link with such software product, for a
period of ninety (90) days from the date of purchase from D-Link or its Authorized
Reseller. D-Link warrants the magnetic media, on which D-Link provides its software
product, against failure during the same warranty period. This warranty applies to
purchased software, and to replacement software provided by D-Link pursuant to this
warranty, but shall not apply to any update or replacement which may be provided for
download via the Internet, or to any update which may otherwise be provided free of
charge.
Copyright 2003 D-Link Corporation.
Contents subject to change without prior notice.
D-Link is a registered trademark of D-Link Corporation|D-Link Systems, Inc. All other
trademarks belong to their respective proprietors.
Copyright Statement
No part of this publication may be reproduced in any form or by any means or used to
make any derivative such as translation, transformation, or adaptation without permission
from D-Link Corporation|D-Link Systems Inc., as stipulated by the United States
Copyright Act of 1976.
D-Link's sole obligation under this software warranty shall be to replace any defective
software product with product which substantially conforms to D-Link's applicable product
documentation. Purchaser assumes responsibility for the selection of appropriate
application and system|platform software and associated reference materials. D-Link
makes no warranty that its software products will work in combination with any hardware,
or any application or system|platform software product provided by any third party,
excepting only such products as are expressly represented, in D-Link's applicable product
documentation as being compatible. D-Link's obligation under this warranty shall be a
reasonable effort to provide compatibility, but D-Link shall have no obligation to provide
compatibility when there is fault in the third-party hardware or software. D-Link makes no
warranty that operation of its software products will be uninterrupted or absolutely error-
free, and no warranty that all defects in the software product, within or without the scope of
D-Link's applicable product documentation, will be corrected.
iv

DGS-3212SR Switch CLI Reference
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
this user’s guide, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate
measures.
VCCI Warning
v

Table of Contents
Introduction ............................................................................................... 1
Using the Console CLI.............................................................................. 3
Command Syntax ..................................................................................... 7
Basic Switch Commands.......................................................................... 9
Switch Port Commands .......................................................................... 30
SNMP Commands.................................................................................. 35
Download|Upload Commands................................................................ 70
Network Monitoring Commands .............................................................73
MAC Notification ..................................................................................... 89
Spanning Tree Commands.....................................................................96
Forwarding Database Commands........................................................ 105
Broadcast Storm Control Commands................................................... 115
QOS Commands...................................................................................118
802.1X COMMANDS............................................................................127
Access Control List (ACL) Commands................................................. 142
Traffic Segmentation.............................................................................151
Stacking ................................................................................................ 154
Port Mirroring Commands.....................................................................157
VLAN Commands................................................................................. 163
Link Aggregation Commands ...............................................................173
IP Interface Commands........................................................................180
Routing Table Commands....................................................................183
IGMP Snooping Commands................................................................. 187
Command History List........................................................................... 197
Technical Specifications ....................................................................... 202

DGS-3212SR Switch CLI Reference
1
INTRODUCTION
The switch can be managed through the switch’s serial port, Telnet, or the Web-
based management agent. The Command Line Interface (CLI) can be used to
configure and manage the switch via the serial port or Telnet interfaces.
This manual provides a reference for all of the commands contained in the CLI.
Configuration and management of the switch via the Web-based management
agent is discussed in the User’s Guide.
Accessing the Switch via the Serial Port
Figure 1-1. Initial Console screen.
The switch’s serial port’s default settings are as follows:
• 9600 baud There is no initial username or password. Just press the Enter key twice to display
the CLI input cursor −DGS-3212SR:4#.This is the command line where all
commands are input.
• no parity
• 8 data bits
Setting the Switch’s IP Address
• 1 stop bit
A computer running a terminal emulation program capable of emulating a VT-100
terminal and a serial port configured as above is then connected to the switch’s
serial port via an RS-232 DB-9 cable.
Each Switch must be assigned its own IP Address, which is used for
communication with an SNMP network manager or other TCP|IP application (for
example BOOTP, TFTP). The switch’s default IP address is 10.90.90.90. You can
change the default Switch IP address to meet the specification of your networking
address scheme.
With the serial port properly connected to a management computer, the following
screen should be visible. If this screen does not appear, try pressing Ctrl+r to
refresh the console screen. The switch is also assigned a unique MAC address by the factory. This MAC
address cannot be changed, and can be found from the initial boot console screen
– shown below.
Introduction
1

DGS-3212SR Switch CLI Reference
The IP interface named System on the switch can be assigned an IP address and
subnet mask which can then be used to connect a management station to the
switch’s Telnet or Web-based management agent.
Figure 1-2. Boot Screen
The switch’s MAC address can also be found from the Web management program
on the Switch Information (Basic Settings) window on the Configuration menu. Figure 1-3. Assigning the Switch an IP Address
The IP address for the switch must be set before it can be managed with the Web-
based manager. The switch IP address can be automatically set using BOOTP or
DHCP protocols, in which case the actual address assigned to the switch must be
known.
In the above example, the switch was assigned an IP address of 10.42.73.100 with
a subnet mask of 255.0.0.0. The system message Success indicates that the
command was executed successfully. The switch can now be configured and
managed via Telnet and the CLI or via the Web-based management agent using
the above IP address to connect to the switch.
The IP address may be set using the Command Line Interface (CLI) over the
console serial port as follows:
Starting at the command line prompt, enter the commands config ipif System
ipaddress xxx.xxx.xxx.xxx|yyy.yyy.yyy.yyy. Where the x’s represent the IP
address to be assigned to the IP interface named System and the y’s represent the
corresponding subnet mask.
Alternatively, you can enter config ipif System ipaddress xxx.xxx.xxx.xxx/z.
Where the x’s represent the IP address to be assigned to the IP interface named
System and the zrepresents the corresponding number of subnets in CIDR
notation.
Introduction
2

DGS-3212SR Switch CLI Reference
• VT-100 compatible
2 • 9,600 baud
• 8 data bits
USING THE CONSOLE CLI • No parity
• One stop bit
The DGS-3212SR supports a console management interface that allows the user
to connect to the switch’s management agent via a serial port and a terminal or a
computer running a terminal emulation program. The console can also be used
over the network using the TCP|IP Telnet protocol. The console program can be
used to configure the switch to use an SNMP-based network management
software over the network.
• No flow control
You can also access the same functions over a Telnet interface. Once you have set
an IP address for your Switch, you can use a Telnet program (in VT-100
compatible terminal mode) to access and control the Switch. All of the screens are
identical, whether accessed from the console port or from a Telnet interface.
After the switch reboots and you have logged in, the console looks like this:
This chapter describes how to use the console interface to access the switch,
change its settings, and monitor its operation.
Note: Switch configuration settings are saved to non-volatile RAM
using save command. The current configuration will then be retained
in the switch’s NV-RAM, and reloaded when the switch is rebooted. If
the switch is rebooted without using the save command, the last
configuration saved to NV-RAM will be loaded.
Connecting to the Switch
The console interface is used by connecting the Switch to a VT100-compatible
terminal or a computer running an ordinary terminal emulator program (e.g., the
HyperTerminal program included with the Windows operating system) using an
RS-232C serial cable.
Figure 2-1. Initial Console Screen
Commands are entered at the command prompt, DGS-3212SR:4#.
Your terminal parameters will need to be set to:
Using the Console CLI
3

DGS-3212SR Switch CLI Reference
There are a number of helpful features included in the CLI. Entering the ?
command will display a list of all of the top-level commands.
Figure 2-3. Example Command Parameter Help
In this case, the command config account was entered with the parameter
<username>. The CLI will then prompt you to enter the <username> with the
message, Next possible completions:. Every command in the CLI has this
feature, and complex commands have several layers of parameter prompting.
Figure 2-2. The ? Command
The dir command has the same function as the ? command.
When you enter a command without its required parameters, the CLI will prompt
you with a Next possible completions: message. In addition, after typing any given command plus one space, you can see all of the
next possible sub-commands, in sequential order, by repeatedly pressing the Tab
key.
To re-enter the previous command at the command prompt, press the up arrow
cursor key. The previous command will appear at the command prompt.
Using the Console CLI
4

DGS-3212SR Switch CLI Reference
Figure 2-4. Using the Up Arrow to Re-enter a Command Figure 2-5. The Next Available Commands Prompt
In the above example, the command config account was entered without the
required parameter <username>, the CLI returned the Next possible
completions: <username> prompt. The up arrow cursor control key was pressed
to re-enter the previous command (config account) at the command prompt. Now
the appropriate User name can be entered and the config account command re-
executed.
The top-level commands consist of commands like show or config. Most of these
commands require one or more parameters to narrow the top-level command. This
is equivalent to show what? or config what? Where the what? is the next
parameter.
For example, if you enter the show command with no additional parameters, the
CLI will then display all of the possible next parameters.
All commands in the CLI function in this way. In addition, the syntax of the help
prompts are the same as presented in this manual −angle brackets < > indicate a
numerical value or character string, braces { } indicate optional parameters or a
choice of parameters, and brackets [ ] indicate required parameters.
If a command is entered that is unrecognized by the CLI, the top-level commands
will be displayed under the Available commands: prompt.
Using the Console CLI
5

DGS-3212SR Switch CLI Reference
Figure 2-6. Next possible completions: Show Command
In the above example, all of the possible next parameters for the show command
are displayed. At the next command prompt, the up arrow was used to re-enter the
show command, followed by the account parameter. The CLI then displays the
user accounts configured on the switch.
Using the Console CLI
6

DGS-3212SR Switch CLI Reference
[square brackets]
Purpose Encloses a required value or set of required arguments. One or more values or arguments
can be specified.
Syntax create account [admin|user]
Description In the above syntax example, you must specify either an admin or a user level account to be
created. Do not type the square brackets.
Example
Command create account admin
3
COMMAND SYNTAX
The following symbols are used to describe how command entries are made and
values and arguments are specified in this manual. The online help contained in
the CLI and available through the console interface uses the same syntax.
<angle brackets>
Purpose Encloses a variable or value that must be
specified.
Syntax create ipif System ipaddress
<network_address>
Description In the above syntax example, you must type
create ipif System followed by the network
address in the <network_address> space. Do
not type the angle brackets.
Example
Command create ipif System ipaddress 10.24.22.5/55.0.0.0
| vertical bar
Purpose Separates two or more mutually exclusive items
in a list −one of which must be entered.
Syntax show snmp [community|trap receiver|detail]
Description In the above syntax example, you must specify
either community, trap receiver, or detail. Do
not type the backslash.
Example
Command show snmp community
Command Syntax
7

DGS-3212SR Switch CLI Reference
{braces}
Purpose Encloses an optional value or set of optional
arguments.
Syntax config igmp [<ipif_name>|all] {version
<value>|query_interval
<sec>|max_response_time <sec>|
robustness_variable
<value>|last_member_query_interval
<value>|state [enable|disable]}
Description In the above syntax example, you must choose
to enter an IP interface name in the <ipif_name>
space or all, but version <value>, query_interval
<sec>, max_response_time <sec>,
robustness_variable <value>,
last_member_query_interval <value>, and state
[enable|disable] are all optional arguments. You
can specify any or all of the arguments
contained by braces. Do not type the braces.
Example
command config igmp all version 2
Line Editing Key Usage
Delete Deletes character under the cursor and then
shifts the remaining characters in the line to the
left.
Backspace Deletes the character to the left of the cursor
and shifts the remaining characters in the line to
the left.
Left Arrow Moves the cursor to the left.
Up Arrow Displays the previous command
Down Arrow Displays the next possible command list, one-
by-one.
Right Arrow Moves the cursor to the right.
Tab Shifts the cursor to the next field to the left.
Multiple Page Display Control Keys
Space Displays the next page.
CTRL+c Stops the display of remaining pages when
multiple pages are to be displayed.
ESC Stops the display of remaining pages when
multiple pages are to be displayed.
n Displays the next page.
p Displays the previous page.
q Stops the display of remaining pages when
multiple pages are to be displayed.
r Refreshes the pages currently displaying.
a Displays the remaining pages without pausing
between pages.
Enter Displays the next line or table entry.
Command Syntax
8

DGS-3212SR Switch CLI Reference
4
BASIC SWITCH COMMANDS
The basic switch commands in the Command Line Interface (CLI) are listed
(along with the appropriate parameters) in the following table.
Command Parameters
create account [admin|user]
<username>
config account <username>
show account
show session
show switch
show serial_port
config serial_port baud_rate [9600|19200|38400|115200]
auto_logout [never|2_minutes|5_minutes
|10_minutes|15_minutes]
enable clipaging
disable clipaging
enable telnet <tcp_port_number>
disable telnet
enable web <tcp_port_number>
disable web
save
reboot
reset {config|system}
Command Parameters
lo
g
in
logout
Each command is listed, in detail, in the following sections.
Basic Switch Commands
9

DGS-3212SR Switch CLI Reference
create account
Purpose Used to create user accounts
Syntax create [admin|user] <username>
Description The create account command is used to create
user accounts that consist of a username of 1 to
15 characters and a password of 0 to 15
characters. Up to 8 user accounts can be
created.
Parameters Admin <username>
User <username>
Restrictions Only Administrator-level users can issue this
command.
Usernames can be between 1 and 15
characters.
Passwords can be between 0 and 15
characters.
Example Usage:
To create an administrator-level user account with the username “dlink”.
DGS-3212SR:4#create account admin dlink
Command: create account admin dlink
Enter a case-sensitive new password:****
Enter the new password again for confirmation:****
Success.
DGS-3212SR:4#
Basic Switch Commands
10

DGS-3212SR Switch CLI Reference
config account
Purpose Used to configure user accounts
Syntax config account <username>
Description The config account command configures a
user account that has been created using the
create account command.
Parameters <username>
Restrictions Only Administrator-level users can issue this
command.
Usernames can be between 1 and 15
characters.
Passwords can be between 0 15 characters.
Example Usage:
To configure the user password of “dlink” account:
DGS-3212SR:4#config account dlink
Command: config account dlink
Enter a old password:****
Enter a case-sensitive new password:****
Enter the new password again for confirmation:****
Success.
DGS-3212SR:4#
Basic Switch Commands
11

DGS-3212SR Switch CLI Reference
show account
Purpose Used to display user accounts
Syntax show account
Description Displays all user accounts created on the
switch. Up to 8 user accounts can exist on the
switch at one time.
Parameters None.
Restrictions None.
Example Usage:
To display the accounts that have been created:
DGS-3212SR:4#show account
Command: show account
Current Accounts:
Username Access Level
--------------- ------------
dlink Admin
DGS-3212SR:4#
Basic Switch Commands
12

DGS-3212SR Switch CLI Reference
delete account
Purpose Used to delete an existing user account
Syntax delete account <username>
Description The delete account command deletes a user
account that has been created using the create
account command.
Parameters <username>
Restrictions Only Administrator-level users can issue this
command.
Example Usage:
To delete the user account “System”:
DGS-3212SR:4#delete account System
Command: delete account System
Success.
DGS-3212SR:4#
Basic Switch Commands
13

DGS-3212SR Switch CLI Reference
show session
Purpose Used to display a list of currently logged-in
users.
Syntax show session
Description This command displays a list of all the users
that are logged-in at the time the command is
issued.
Parameters None
Restrictions None.
Example Usage:
To display the way that the users logged in:
DGS-3212SR:4#show session
ID Login Time Live Time From Level Name
-- -------------------------- ------------ ------------ ----- ---------
8 0000 days 00:05:54 0:17:16.2 Serial Port 4 Anonymous
Basic Switch Commands
14