D-Link DES-7200 Instruction Manual

. i
DES-7200
Basic Configuration Command
Reference Guide
Version 10.4(3)
DES-7200 CLI Reference Guide

. ii
Revision No.:Version 10.4(3)
Date:
Copyright Statement
D-Link Corporation ©2011
All rights reserved.
Without our written permission, this document may not be excerpted, reproduced,
transmitted, or otherwise in all or in part by any party in any means.

. iii
Preface
Version Description
This manual matches the firmware version 10.4(3).
Target Readers
This manual is intended for the following readers:
Network engineers
Technical salespersons
Network administrators
Conventions in this Document
1. Universal Format Convention
Arial: Arial with the point size 10 is used for the body.
Note: A line is added respectively above and below the prompts such as caution and note to
separate them from the body.
Format of information displayed on the terminal: Courier New, point size 8, indicating the
screen output. User's entries among the information shall be indicated with bolded
characters.
2. Command Line Format Convention
Arial is used as the font for the command line. The meanings of specific formats are
described below:
Bold: Key words in the command line, which shall be entered exactly as they are displayed,
shall be indicated with bolded characters.
Italic: Parameters in the command line, which must be replaced with actual values, shall be
indicated with italic characters.
[ ]: The part enclosed with [ ] means optional in the command.
{ x | y | ... }: It means one shall be selected among two or more options.
[ x | y | ... ]: It means one or none shall be selected among two or more options.
//:Lines starting with an exclamation mark "//" are annotated.

. iv
3. Signs
Various striking identifiers are adopted in this manual to indicate the matters that special
attention should be paid in the operation, as detailed below:
Caution
Warning, danger or alert in the operation.
Note
Descript, prompt, tip or any other necessary supplement or explanation for
the operation.
Note
The port types mentioned in the examples of this manual may not be
consistent with the actual ones. In real network environments, you need
configure port types according to the support on various products.
The display information of some examples in this manual may include the
information on other series products, like model and description. The details
are subject to the used equipments.

DES-7200 CLI Reference Guide Chapter 1CLI Authorization Configuration Commands
. 1-1
1CLI Authorization
Configuration Commands
1.1 alias
You can use the alias command to configure an alias of a command in the
global configuration mode. Use the no form of the command to remove the alias
of a specified command or all the aliases under one mode.
alias mode command-alias original-command
no alias mode command-alias
Parameter Description
mode Mode of the command represented by
the alias
command-alias Alias of the command
Parameter
description
original-command Syntax of the command represented
by the alias
Default
Settings Some commands in the privileged EXEC mode have
default alias names.
Command
mode Global configuration mode.
Usage
guidelines
The following table lists the default alias of the commands
in the privileged EXEC mode.
Alias Actual Command
h help
p ping
s show

DES-7200 CLI Reference Guide Chapter 1CLI Authorization Configuration Commands
. 1-2
un undebug
The default alias cannot be deleted by the no alias exec
command.
By setting the alias, you can use a word to replace a
command. For example, you can create an alias to
represent the first part of a command, and then type the
rest part of the command.
The mode of the command represented by the alias is the
command mode existing in the current system. In the
global configuration mode, you can use alias ? to list all
the modes under which you can configure alias for
commands.
DES-7200(config)# alias ?
aaa-gs AAA server group mode
acl acl configure mode
bgp Configure bgp Protocol
config globle configure mode
......
The alias also has its help information that is displayed
after * in the following format:
*command-alias=original-command
For example, in the privileged EXEC mode, the default
alias sstands for show. You can enter s? to query the key
words beginning with sand the help information of the
alias.
DES-7200#s?
*s=show show start-chat start-terminal-service
If an alias represents more than one word, the command
will be displayed in brackets. For example, if you set sv
stand for show version in the privileged EXEC mode,
then:
DES-7200#s?
*s=show *sv="show version" show start-chat
start-terminal-service
The alias must begin with the first letter of the command.
The first letter of the command cannot be a space. The
space before the command cannot be used as a valid
alias.
DES-7200# s?
show start-chat start-terminal-service
The command alias also has its help information. For
example, if the alias ia represents ip address in the

DES-7200 CLI Reference Guide Chapter 1CLI Authorization Configuration Commands
. 1-3
interface configuration mode, then:
DES-7200(config-if)#ia ?
A.B.C.D IP address
dhcp IP Address via DHCP
DES-7200(config-if)# ip address
The above help information lists the parameters of ip
address and shows the actual command name.
You must enter an entire alias; otherwise it cannot be
recognized.
Use the show aliases command to show the aliases
setting in the system.
Examples
In the global configuration mode, use def-route to
represent the default route setting of ip route 0.0.0.0
0.0.0.0 192.168.1.1:
DES-7200# configure terminal
DES-7200(config)# alias config def-route ip route 0.0.0.0
0.0.0.0 192.168.1.1
DES-7200(config)#def-route?
*def-route="ip route 0.0.0.0 0.0.0.0 192.168.1.1"
DES-7200(config)# end
DES-7200# show aliases config
globle configure mode alias:
def-route ip route 0.0.0.0 0.0.0.0
192.168.1.1
Command Description
Related
commands show aliases Show the aliases settings.
1.2 privilege
To attribute the execution rights of a command to a command level, use
privilege in the global configuration mode. The no form of this command
recovers the execution rights of a command to the default setting.
privilege mode [all] [level level | reset ]command-string
no privilege mode [all] [level level ]command-string
Parameter Description
mode CLI mode of the command to which
the execution rights are attributed.
all Alias of the command
Parameter
description
level Specify the execution right levels

DES-7200 CLI Reference Guide Chapter 1CLI Authorization Configuration Commands
. 1-4
(0–15) of a command or
sub-commands
reset Restore the command execution rights
to its default level
command-string: Command string to be authorized
Default
Settings N/A.
Command
mode Global configuration mode.
Usage
guidelines
The following table lists some key words that can be
authorized by command privilege in the CLI mode. The
number of command modes that can be authorized may
vary with different devices. In the global configuration
mode, you can use privilege ? to list all CLI command
modes that can be authorized.
Mode Descripton
config Global configuration mode.
exec Privileged EXEC mode
interface Interface configuration mode
ip-dhcp-pool DHCP address pool
configuration mode
keychain KeyChain configuration mode
keychain-key KeyChain-key configuration
mode
time-range Time-Range configuration mode
Examples
Set the password of CLI level 1 as test and attribute the
reload rights to reset the device:
DES-7200(config)#enable secret level 1 0 test
DES-7200(config)#privilege exec level 1reload
After the above setting, you can access the CLI window as
level-1 user to use the reload command:
DES-7200>reload ?
LINE Reason for reload

DES-7200 CLI Reference Guide Chapter 1CLI Authorization Configuration Commands
. 1-5
<cr>
You can use the key word all to attribute all sub-commands
of reload to level-1 users:
DES-7200(config)# privilege exec all level 1 reload
After the above setting, you can access the CLI window as
level-1 user to use all sub commands of the reload
command:
DES-7200>reload ?
LINE Reason for reload
at reload at a specific time/date
cancel cancel pending reload scheme
in reload after a time interval
<cr>
Command Description
Related
commands enable secret Set CLI-level password
1.3 show aliases
To display all the command aliases or aliases in special command modes, run
the show aliases command in the privileged EXEC mode.
show aliases [mode]
Parameter Description
Parameter
description mode Mode of the command represented by
the alias.
Default
Settings N/A.
Command
mode EXEC mode.
Usage
guidelines Show all the configuration of aliases if the command mode
has not been input.
Examples Following example shows the command alias in the EXEC
mode:
DES-7200#show aliases exec

DES-7200 CLI Reference Guide Chapter 1CLI Authorization Configuration Commands
. 1-6
exec mode alias:
h help
p ping
s show
u undebug
un undebug
Command Description
Related
commands alias Set the alias of a command.