D-Link mydlink DCH-G022 User manual

DCH-G022 D-Link Corporation
Page 1
DCH-G022
mydlink™ Connected Home Hub
User’s Manual
Version 1.0
Jun. 25th, 2016

DCH-G022 D-Link Corporation
Page 2
Table of Contents
1. PRODUCT DESCRIPTION..................................................................................3
2. APPEARANCE .....................................................................................................3
3. APPLICATIONS ...................................................................................................4
4. INSTALLATIONS & BASIC CONFIGURATIONS ...........................................4
5. ADVANCED CONFIGURATIONS ...................................................................10
6. ADDITIONAL NOTES.......................................................................................13

DCH-G022 D-Link Corporation
Page 3
1. PRODUCT DESCRIPTION
The DCH-G022 is a Connected Home Z-Wave Gateway used to control a
variety of Z-wave home sensors for the application of home automation.
It is able to talk to variety of Z-Wave sensors and communicate with other D-
Link connected Home devices.
DCH-G022 is a Security Enabled Z-Wave Plus product.
2. APPEARANCE
Front Panel
LED: Status indicator
Rear Panel
USB port (Type A): reserved for future support.
LAN port x2
Wireless button: Device inclusion/ exclusion and Wi-Fi connecting

DCH-G022 D-Link Corporation
Page 4

Power jack: 5V/2A
Bottom Panel
Reset button
PIN Code: Code for App binding and web configuration UI password

DCH-G022 D-Link Corporation
Page 5
3. APPLICATIONS
4. INSTALLATIONS & BASIC CONFIGURATIONS
Step 1 Make sure your mobile device connected to the same network as DCH-G022
Step 2 Follow the Quick Install Card to scan the QR code to download the App.
Step 3 Install App and run it.
Step 4 Register an account for mydlink home service and login the App.
Step 5 Add a new device and select Gateway DCH-G022.
A. Select Add new device to add a DCH-G022.

DCH-G022 D-Link Corporation
Page 6
B. Scan device QR code or skip the QR code to manual select the device.
Step 6 Follow the instructions to setup the DCH-G022

DCH-G022 D-Link Corporation
Page 7
Step 7 Find the DCH-G022, select it or need to enter the PIN Code of your DCH-
G022 if choose manual setup.

DCH-G022 D-Link Corporation
Page 8
Step 8 Set time zone of your DCH-G022.
Step 9 Give a name and a photo for your DCH-G022.

DCH-G022 D-Link Corporation
Page 9
Click the device to see more information of the device.
Make a Policy for Devices

DCH-G022 D-Link Corporation
Page 10
Make a Group for Devices

DCH-G022 D-Link Corporation
Page 11
5. ADVANCED CONFIGURATIONS
Before enter the advance configuration, you need to open an Internet browser on
the PC and type http://dch-g022’s IP address/ to ogin the web page
Input the fo owings:
User name: admin
Password: device PIN code (6 digits)
Note: you can find the PIN code on the device label.
5.1 Firmware Update page
After successfu og-in, c ick the Firmware Upgrade tab on the eft, then you wi
enter the firmware update page.
FW upgrade: Se ect the FW fi e first, and then press the “Up oad” button.

DCH-G022 D-Link Corporation
Page 12
5.2 Factory Default page
After successfu og-in, c ick the Factory Defau t tab on the eft, then you wi
enter the factory defau t page.
Press Restore Factory Defau t button to reset the device to factory defau t va ue
Press Partia Reset button to reset system except Z-Wave contro er.
5.3 Z-Wave Main page
This page a ows the user to do the advanced Z-Wave configuration of DCH-
G022. After successfu og-in, c ick the Z-Wave Main tab on the eft, then you
wi enter the Z-Wave Main page.
5.3.1 Z-Wave Basic Commands:
o Include Device / Exclude Device: Press the This process (a so known as
"inc usion" and "adding") is achieved by pressing/(ho d for 5 seconds) “Wire ess

DCH-G022 D-Link Corporation
Page 13
button” on DCH-G022 to achieve inc ude device. Or you can pushing the
“Inc ude NEW Device” feature on Web GUI to add device. To exc ude a device,
p ease press “Exc ude Device” button on web GUI.
Learn Mode: Starts earn mode for DCH-G022 if it is needed to inc ude it as s ave
in another contro er’s network. When DCH-G022 is a ready inc uded in a
network, triggering “Learn Mode”again can Copy (do rep ication) atest network
information from SUC.
Reset Z-Wave Controller: Reset the Z-Wave contro er on y.
This product can be inc uded and operated in any Z-Wave network with other Z-
Wave certified devices from other manufacturers and/or other app ications. A
non-battery operated nodes within the network wi act as repeaters regard ess
of vendor to increase re iabi ity of the network.
5.3.2 Status and Information:
Node ID: Disp ay the node ID of the DCH-G022
Home ID: Disp ay the current Home ID of the DCH-G022
Node Information: Disp ay the basic type, generic type and specific type of DCH-
G022.
ZW_Capabi ity: the Z-Wave capabi ities of DCH-G022
SUC_ID: the ID of Static Update Server
5.4 Z-Wave Nodes page
This page a ows the user to do the advanced Z-Wave configuration of other Z-
Wave sensors. After successfu og-in, c ick the Z-Wave Nodes tab on the eft, then
you wi enter the Z-Wave Nodes page.

DCH-G022 D-Link Corporation
Page 14
(Please refresh the GUI to show up the newest status)

DCH-G022 D-Link Corporation
Page 15
: To send NOP to test if sensor node can response (with ack) correctly. If
device can response immediately, the “sleeping” state will be 0. Otherwise it will
be 1 which means the device may be sleeping or out of work.
: After send NOP to check that node is sleeping or out of work (value is 1),
user can remove the failed node. (Before removing failed node, please manually
wake up the node to check if it really failed)
: After send NOP to check that node is sleeping or out of work (value is 1),
user can replace the failed node. (Before replacing failed node, please manually
wake up the node to check if it really failed)
: Send the BASIC SET ON command to switch end point (e.g.: ep0) of
the node ON.
: Send the BASIC SET OFF command to switch end point (e.g.: ep0) the
node OFF.
: Send the BASIC GET command to the end point (e.g.: ep0) of selected
node.
“Network: S” : (Security) Node is included by DCH-G022 with security
“Network: NS”: (Non-Security) Node is included by DCH-G022 without security
6. ADDITIONAL NOTES
The Z-Wave Grouping Identifier of DCH-G022 is 1 and used for the Lifeline
association.
The maximum number of devices that can be added to the group is 1.
Being a slave controller, DCH-G022 will ignore / do nothing when getting basic
GET/SET command
This controller is the primary controller for your network, resetting it will result in
the nodes in your network being orphaned and it will be necessary after the reset
to exclude and re-include all of the nodes in the network. If this controller is
being used as a secondary controller in the network, use this procedure to reset
this controller only in the event that the network primary controller is missing or
otherwise inoperable.