D-Link RG-S8614 Installation and operating manual

RG-S8600 Series Switch
Hardware Installation and Reference Guide V1.78

Copyright statement
Ruijie Networks©2000-2014
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification, transmission, translation
or commercial use of this document or any portion of this document, in any form or by any means, without the prior written consent of
Ruijie Networks is prohibited.
, , , , , ,
, , ,
, , are registered trademarks of Ruijie Networks. Counterfeit is
strictly prohibited.
Exemption statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain the latest
information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will not shoulder any
responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the switch.
Scope
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks website: http://www.ruijienetworks.com
Online customer services: http://webchat.ruijie.com.cn
Customer service center: http://www.ruijie.com.cn/service.aspx
Customer services hotline: [phone]
BBS: http://support.ruijie.com.cn
Customer services email: s[email protected]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Documentation Conventions
The symbols used in this document are described as below:
This symbol draws the attention of readers to some suggestions and references.
This symbol reminds readers to be alert of wrong operations that may lead to loss of data or damage to equipment.

Chapter 1 Product Overview
The RG-8600 switch is a module-based high-density multi-service IPv6 10Gbp score routing switch developed by Ruijie
Networks, providing powerful defense capability based on high performance and capacity. It can be expanded according
to users’ business needs, satisfying the design requirements for putting equal emphasis on service and performance.
The RG-S8600 switch provides dual management boards and dual power supplies for redundancy. Currently four models
are available:
The RG-S8614: designed with 14 transverse slots, supporting dual management engine modules, providing 12 slots
for service modules.
The RG-S8610: designed with 10 vertical slots, supporting dual management engine modules and providing eight
slots for service modules.
The RG-S8606: designed with six transverse slots, supporting dual management engine modules and providing four
slots for service modules.
The RG-S8606 B: designed with six transverse slots, supporting dual management engine modules and providing
four slots for service modules.
RG-S8614
The RG-8600 switch is an A-class product and may cause radio disturbance to surroundings. In this case, users are
advised to take proper measures against the disturbance.
Specifications
Model
RG-S8614
Module Slot
14 (two for management engine modules)
Module Type
M8614-CM II
M8600-24SFP/12GT
M8600-24GT/12SFP
M8600P-24GT/12SFP
M8600-02XFP
M8600-48GT/4SFP
M8600P-48GT/4SFP
M8600-04XFP
M8600-24SFP
M8600-MPLS
M8600-NMM
M8600-02XFP24SFP/12GT-E
M8600-08XFP
M8600-VSU-02XFP
M8600-FW
RG-WALL 1600-B-E
RG-WALL 1600-B-U
RG-WALL 1600 FW Module
M8600-WS
M8600-02XFP24SFP/12GT-EC
M8600-24SFP/12GT-EC
M8600-48GT/4SFP-EC
M8600P-48GT/4SFP-EC
M8600-24GT/12SFP-EC
M8600-04XFP-EC
M8600-04QXS-DA
M8600-16XS-DA
Hot Swapping
Supported
Management
Redundancy
Supported

Power Supply
RG-PA1200:90 ~ 264VAC, 47 ~ 63Hz, power: 1200W
RG-PA1200E: 90 ~ 264VAC, 47 ~ 63Hz, power: 1200W
RG-PA2000: 90 ~ 176VAC, 47 ~ 63Hz, power: 1200W
176 ~ 264VAC, 47 ~ 63Hz, power: 2000W
RG-PA1200I: 90 ~ 176VAC, 47 ~ 63Hz, power: 530W
176 ~ 264VAC, 47 ~ 63Hz, power: 1400W
RG-PA2000I: 90 ~ 176VAC, 47 ~ 63Hz, power: 1080W
176 ~ 264VAC, 47 ~ 63Hz, power: 2000W
RG-PD1200: -36 ~ -72VDC, power: 1200W
RG-PD2000: -36 ~ -72VDC, power: 2000W
PA stands for AC power; PD stands for DC power.
Power Supply
Redundancy
The power supply redundancy of the same model is supported
Fan
GB9254-2008
EMC Standards
GB4943-2011
Safety
Standards
GB4943-2011
Operating
Temperature
0 ~ 40°C
Storage
Temperature
-40 ~ 70°C
Operating
Humidity
10% ~ 90% RH (non-condensing)
Earthquake
Resistance
Able to resist the earthquake intensity 9
Weight
≤114 kg
Dimensions
(W x D x H)
436.8 mm x 508 mm x 932.2 mm, 21 RU
Product Appearance
Figure 1-1 Appearance of the RG-S8614 Switch

Note:
Modular layer: offers up to 14 module slots
Power layer: supports up to twoAC or DC power supplies
Air outlet: Located in the back of the chassis, as the air-outlet unit of the
system.
The RG-S8614 switch’s hardware system is composed of the chassis, the power system, modules, the fan tray and
the air filter.
Chassis
The RG-S8614 switch has a standard 19-inch chassis, which is 932.2mm high, 436.8mm wide and 508mm deep. It
consists of the system modular layer, the fan layer, the air filter and the power system layer.
The system modular layer is a module subrack that mechanically supports various modules of the RG-S8614.The
modular subrack is composed of module slots and back panel.
At the bottom of the chassis are two power frames. The air filter is located on the right side of the module subrack of the
chassis, facing the front of the chassis. On the back of the module subrack is the fan layer, which houses ten fans working
to suction air.
Module Slot
The RG-S8614 switch provides 14 module slots, of which two in the middle are only for the management modules. The 12
slots on the top and the bottom can accommodate a mix of various modules. Modules are inserted horizontally, with the
same height of 412 mm, and depth of 350 mm.
When all the slots are occupied, the modules in the subrack of the RG-S8614 switch are configured as follows:
Two management modules as backup for each other
12 modules are selected according to needs
The slots for the two management modules are in the middle and identified as M1 and M2 from bottom to top; the other 12
line cards are numbered 1-12 from bottom to top.




Backplane
The RG-S8614 switch’s backplane interconnects high-speed data links from switch management board to module circuit
board and various management and control signals between modules. Its functions are as follows:
Interconnects all signals between modules and provide high-speed communication channel.
Passive backplane
Supports active/standby switching between management modules
Supports automatic identification of various slots
Implements distributed power supply
Introduces monitoring signal lines of the fan and power supply
Ventilation and Heat Dissipation System
The operating temperature of the RG-S8614 switch is 0 to 40°C. The thermal design must ensure that the surface
temperature of the components does not exceed 50% to 80% of the allowed maximum temperature and satisfy the
requirement on the device’s reliability in the temperature range while ensuring the device’s reliability, safety and
maintainability. According to the thermal design of the RG-S8614 switch, fans are used to draw air for forced convection
cooling in order to ensure that the device works properly in the specified environment.

Figure 1-2 Ventilation and Heat Dissipation System of the RG-S8614 Switch
This structure is designed with air inlet on two sides, and air outlet at the back. The air flow direction is shown above.
Ten 120 x 120 x 38 fans are used to blow air outside for convection and ultimately heat dissipation. The chassis
should be mounted in a place with sufficient space for air circulation. Sufficient space (10 cm at least) must be
reserved at the air intakes and exhaust vents for ventilation.
RG-S8610
The RG-8600 series is an A-class product and may cause radio disturbance to surroundings. In this case, users are
advised to take proper measures against the disturbance.
Specifications
Model
RG-S8610
Module Slot
10 (two for management engine modules)

Module Type
M8610-CM
M8610-CM II
M8610-CM III
M8610-CM II LITE
M8600-24SFP/12GT
M8600-24GT/12SFP
M8600P-24GT/12SFP
M8600-02XFP
M8600-48GT/4SFP
M8600P-48GT/4SFP
M8600-04XFP
M8600-24SFP
M8600-MPLS
M8600-NMM
M8600-02XFP24SFP/12GT-E
M8600-08XFP
M8600-VSU-02XFP
M8600-FW
RG-WALL 1600-B-E
RG-WALL 1600-B-U
RG-WALL 1600 FW Module
M8600-WS
M8600-02XFP24SFP/12GT-EC
M8600-24SFP/12GT-EC
M8600-48GT/4SFP-EC
M8600P-48GT/4SFP-EC
M8600-24GT/12SFP-EC
M8600-04XFP-EC
M8600-04QXS-DA
M8600-16XS-DA
Hot Swapping
Supported
Management Redundancy
Supported
Power Supply
RG-PA1200: 90 ~ 264VAC, 47 ~ 63Hz, power: 1200W
RG-PA1200E: 90 ~ 264VAC, 47 ~ 63Hz, power: 1200W
RG-PA2000: 90 ~ 176VAC, 47 ~ 63Hz, power: 1200W
176 ~ 264VAC, 47 ~ 63Hz, power: 2000W
RG-PA1200I: 90 ~ 176VAC, 47 ~ 63Hz, power: 530W
176 ~ 264VAC, 47 ~ 63Hz, power: 1400W
RG-PA2000I: 90 ~ 176VAC, 47 ~ 63Hz, power: 1080W
176 ~ 264VAC, 47 ~ 63Hz, power: 2000W
RG-PD1200: -36 ~ -72VDC, power: 1200W
RG-PD2000: -36 ~ -72VDC, power: 2000W
PA stands for AC power; PD stands for DC power.
Power Supply Redundancy
The Power supply redundancy of the same model is supported
Fan
M8610-FAN (supporting hot swapping and fault alarming)
Environmental
EMC
Standards
GB9254-2008
Safety
Standards
GB4943-2011
Operating
Temperature
0 ~ 40°C
Storage
Temperature
-40 ~ 70°C
Operating
Humidity
10% ~ 90% RH (non-condensing)
Earthquake
Resistance
Able to resist the earthquake intensity 9
Weight
≤93 kg
Dimensions
(W x D x H)
436.8 mm x 448 mm x 956 mm, 21.5 RU

Product Appearance
Figure 1-3 Appearance of the RG-S8610 Switch
Note:
Air outlet layer: the air outlet layer of the whole system, discharge air to the
outside on three sides
Fan tray: slot of the fan tray, the active heat dissipation unit of the system
Modular layer: provides 10 vertical module slots, can house modules with
different functions
Wiring layer: arranges and leads out various cables in good order while
preventing the drooping cables from blocking the air inlet
Air inlet layer: inducts air into the chassis as the airway of the whole heat
dissipation unit;
Power layer: supports up to twoAC or DC power supplies





