D'San Limitimer PRO-2000 User manual

PSL-20VPRO-2000T
Model PRO-2000BT
PSL-20VPRO-2000TBT
TR-2000BT
Speaker Timer
with Remote Signal Light
ASL-4
ASL2-ND3
ASL4-ND3, ASL4-ND3BT
Model PRO-2000

00 00
:
00 0000 00
SESSION
STOPSUM UP-TALKTALK
START
TOTAL TIME
0:00
Options: Beep - Blink
Connect Signal Light to Limitimer with Cat-5 cable
or Cat-5–to–XLR adapter KES 882 (included).
Plug in 12 V power supply (A).
Turn on power switch (B).
Program 1 is the default program.
Note: Blink and beep settings, like time settings,
are set for each program individually.
Blink: Red light starts to blink after it comes on
Beep: Audible cue is sounded on yellow-to-red
light and on red blink
Blink + Beep: Audible cue is sounded on yellow-
to-red change, then, once every other second
when Red light starts to blink.
Note: Hold Beep button to activate a single
manual beep.
Set Total Time
Set Sum-up Time
Press Start.
(A) (B)
Quick Start - Set-up
PSL-PB6
Programs are useful for debates or contests
where pre-set timing formats can be selected
quickly or where timekeeping is separate for each
speaker.
Programs 1, 2, and 3 cannot run simultaneous
with each other. Toggling between these programs
stops the clock. Session 4 is a program that can
run in background to Program 1, 2 or 3.
A dimly-lit Program LED indicates that a program
is running in background. A brightly lit LED
indicates that the program is selected.A signal
light set to display multiple programs displays the
program selected on the timer.
Up to 3 signal lights (PSL-20V or ASL2-ND3) can
be powered from the base timer at a distance of
about 200-feet. Longer distances will produce
power attenuation due to resistance in the cable.
To drive additional lights at greater distances, use
DSan model PSL-PB6 or PSL=PB18 power
distribution hubs with a a appropriate power
supply
To pre-set a
program, select that
program.
Set Total Time,
Sum-up Time, Blink
and Beep.
These settings are
saved for the
selected program.
PROGRAMS
1
2
3
4
SESSION
STOP
STOP
CONTINUE
CLOCK
INDICATOR
Multiple Signal Lights
Using the Programs

“Master” Switch 1 = ON “Slave” Switch 1 = OFF
The Slave timer acts as a client sending keystroke
commands to control the Master and displaying the
time remaining. All the time processing is done in
the Master.
60-feet. Bluetooth devices need to “find” one
another before communicating. This process is
called “pairing.” To pair signal light receiver(s) with
a timer, keep the devices close (< 30-feet) until the
yellow Connection LED turns green. This indicates
that the devices are communicating.
Global settings are common to all programs. They are made on the 12-position DIP switch
on the rear of the timer console. The default settings (shown) are suitable for most uses.
1. Master / Slave.
When two or more timers are connected to one or
more signal lights, set one timer as master [ON]
and the other(s) as slave [OFF]. When only one
timer is used, it must be a master (default setting).
2. Counting Program 4 (Session)
Minutes:Seconds (ON); Hours:Minutes (OFF)
When using Program 4 to time a program over
several hours, set to Hours:Minutes (OFF).
3. Counting Program 1, 2 or 3
Minutes:Seconds (ON) Hours:Minutes (OFF)
4. Count direction
Count-Down [ON] or Count-Up [(OFF].
If Count-Up, Time Remaining display shows
elapsed time, else Time Remaining.
5. Count Behavior
Continue after zero [ON] else, stop display at zero.
Note, in OFF mode, clock continues to run and red
light stays on until user presses “Stop.”
9. Time Settings Permission
Allow time changes while clock is running [ON].
10. Block Transmitter [ON]
Model PRO-2000BT offers wireless transmission to
the remote signal light. Set to “OFF” when using a
wireless connection.
6. Sound Volume
High (ON) Low (OFF)
on
1 2 3 4 5 6 7 8 9 1112
#
Wireless Operation
*An empty sound. “Beep”
pressed on the timer
outputs a cue to activate a
sound at a signal light that
is set for an audible sound.
7.+ 8. Sound Selection
7. ON 8. ON None*
7. OFF 8. ON Buzz
7. ON 8. OFF Ring
7. OFF 8. OFF Chime
Default settings
11 + 12. Wireless Channels (PRO-2000BT)
PRO-2000BT is equipped with an integrated
Bluetooth transceiver. It can communicate with up®
to 6 Bluetooth signal light receivers (TR-2000BT) or
other PRO-2000BT timers on
four different channels. This
allows multiple timer-signal
light networks to operate in
proximity. Match receiver
channel (rotary switch) with
timer channel (DIP switches 11
+ 12) as shown. Note:
Receiver channels 0,4,5,6 not used. The effective
distance for wireless communications is about Bluetooth
Connection LED
Global Settings

Display Lights:
Switch 9 =ON
Program 1 Program 2
9. Display top lights [ON]
10. Display digits [ON]
Display Digits:
Switch 10 = ON
Connect the signal light to the Limitimer console
with the 50-foot Cat-5 cable or the Cat-5–XLR
adapter (both included).
If Limitimer is used in debates or contests where
separate times are maintained for participants, set
the signal lights each to receive only a unique
program. Signal lights may be interconnected to
the timer console along a single cable run.
Caution: Cables carry 12V power.. Do not connect
to audio devices or data ports. Contact DSan for
pinouts to make your own cables.
Use IP-2000X “Network Extender” to make timer-
signal light connections over a network. For more
information, see www.dsan.com/Network .
Use DIP switches on the bottom of the signal light
to set which timer programs to display, whether
sound cues accompany light changes, which phase
lights are active and how the digital display
behaves. All settings are local can can be different
for each signal light connected to the timer.
DIP switches on
bottom of signal light Depressed position = ON
Default Settings
*An empty sound. “Beep”
pressed on the timer
outputs a cue to activate a
sound at a signal light that
is set for an audible sound.
7.+ 8. Sound Selection
7. ON 8. ON None*
7. OFF 8. ON Buzz
7. ON 8. OFF Ring
7. OFF 8. OFF Chime
1-4. Select Timer Programs to be displayed
1. Display Program 1 [ON]
2. Display Program 2 [ON]
3. Display Program 3 [ON]
4. Display Program 4 [ON] (Session)
Since Program 4 can run in background, it might be
useful to use a separate signal light that is enabled
for Program 4 ONLY and another that is enabled for
Programs 1, 2 and/or 3 ONLY. A signal light that is
enabled for multiple programs displays the program
that is selected on the timer.
5. Continue counting after zero [ON] else, stop
display at zero. Note, in OFF mode, the clock
continues to run and red light stays on until user
presses “Stop.” Beep / Blink continue, if set.
6. Sound volume. High [ON] Low [OFF]
Front lights
always active
on
1 2 3 4 5 6 7 8 9 10
Signal Light Settings Signal Light Connections
Network Connections

PSL-20V Extra podium Signal Light
Flush mount podium signal light
for permanent installation
PSL-20VF
Audience signal light with 4” lightsASL4 Audience signal light with 4" digital
display and green-yellow red lights.
ASL4-ND3
Audience signal light with 2” digital
display and green-yellow red lights.
ASL2-ND3
Carrying/storage case holds
Limiitmer system and ASL2-ND3
CS-518
Carrying/storage case for Limitmer
system and ASL4-ND3.
CS-827
50-ft Cat 5 Cable / KES-825 (25-ft)KES-850 Adaptor: Male XLR-to-Modular
Cat 5 Jack
KES-882
Video clock; software and dongle to
display time on LCD monitor
VC-2000
Timer system with integrated
Bluetooth transmitter and external
powered Bluetooth receiver
PRO-2000BT
Adapter to connect timer and signal
light(s) over a local area net or WAN
IP-2000X
Adapter to control Limitimer with
touch panel systems
TP-2000X
Made in USA
Warranty
Instruments made by DSan Corp are warranteed against
defects in materials and workmanship one year from date of
shipment. Any instrument which fails will be restored
free of charge.
Products and accessories available for
purchase online:
www.dsan.com/shop
Limitimer user guides, bulletins, Q&As:
www.dsan.com/Limitimer
@
DSan Corporation
Roslyn Heights, NY 11577
Tel: [phone] Fax: [phone]
[e-mail]
Accessories and Options
Service and Support