Da-Lite ADVANTAGE DELUXE ELECTROL User manual

DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: [phone]
800-622-3737
Fax: [phone]
Toll Free Fax: [phone]
www.da-lite.com
e-mail: [email protected]
POWER
PRESENTATION PRODUCTS
The
In
Instruction Book for
ADVANTAGE®DELUXE ELECTROL®

PRE-INSTALLATION
1
CASE INSTALLATION
1. The case provides multiple attachment points for bolts, cables, or threaded rod. Page 5 shows threaded rod
installed. The variable position-mounting bracket may be located anywhere along the length of the case. It is
recommended to keep the brackets spaced evenly enough to distribute the weight of the screen.
The case has a self-trimming flange around the bottom. Ceiling tiles or drywall may be placed on top of this flange
to provide a finished appearance.
2. After securing the case in the ceiling check that the case is level and plumb.
3. Install electrical connections that apply to your unit. Review the wiring diagrams on pages 3 and 4 for proper
installation. If your screen has the built in SCB-100 or SCB-200, please refer to separate instructions.
1. Carefully unpack screen and remove outer wrapping from case.
2. Make sure to recheck measurements of screen location before installation.
IMPORTANT SAFETY INSTRUCTIONS
When using your video equipment, basic safety precautions should always be followed, including the
following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance
should be used. Cords rated for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this appliance. Contact an authorized
service dealer when repair work is required. Incorrect reassembly can cause electric shock when
the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the manufacturer may cause a risk of
fire, electric shock, or injury to persons.
SAVE THESE INSTRUCTIONS
FABRIC DOOR
ACCESS
DOOR
SCREW FOR
SECURING ROLLER
ACCESS DOOR
FIGURE 1

2
If your screen was shipped with the motor and roller already installed proceed to step 6.
1. Remove the screw from each end of the access door (front door) and open the door. See figure 1.
2. Carefully unpack screen and roller assembly. Leave packing paper on the roller.
3. Place the roller assembly into the case with the motor on the left side. The limit switches should be facing down.
Line up the square pin on the motor with the square hole in the bracket.
4. Lift the pin end (right end) of the roller into position and slide the bracket onto the roller pin. Tighten two nuts to
secure the bracket.
5. Complete electrical hook-up by snapping motor wire connector into case connector.
CAUTION! DO NOT CUT TAPE ON FABRIC WITH A KNIFE OR ANY SHARP TOOL. REMOVE BY HAND.
6. Carefully remove tape strips securing picture surface around roller. Slat should move freely (Fig. 2). (Only if the
roller assembly is preinstalled.)
7. Test installation by operating the screen several times. Be prepared to stop the screen. The fabric door (rear door)
will not close until the wall switch is placed in the up position and when the screen motor stops at its limit switch
in the up direction.
NOTE: Excessive continuous operation may cause the motor to overheat. If this happens the motor will shut off until it cools to
a normal operating temperature.
8. Run the screen down enough to open the fabric door. Close the access door and reinstall the screws to secure the
door.
SCREEN AND ROLLER ASSEMBLY INSTALLATION
SCREEN ADJUSTMENT
Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly
adjusted at Da-Lite. Should it be necessary to adjust for more or less drop of picture, proceed in the following manner:
NOTE: Use a screw driver or 5/32" Allen wrench to make adjustments.
SCREEN MOTOR
FIGURE 2
▲
!
LIMIT SWITCH
ADJUSTMENT
KNOBS
DOOR
MICROSWITCH
FABRIC
DOOR
KNOCKOUTS FOR
CONDUIT INSTALLATION
FIGURE 3
SCB-100/SCB-200
ACCESS COVER
ACCESS DOOR
DOOR MOTOR

3
MORE SCREEN DROP
1. Place operating switch in “down” position.
2. When the screen stops, turn the white “down” limit knob (Fig. 2) one-quarter turn counterclockwise. Test by raising
picture surface approximately two feet, then lower again. Repeat until desired picture surface position is attained.
CAUTION: Do not adjust for more drop than what was ordered. At least 1-1/2 wraps of fabric must remain on the roller. This
screen comes standard with 0" or 2" black at the top. See the specification data sheet for details.
LESS SCREEN DROP
1. Raise picture surface approximately two feet above desired level.
2. Place operating switch in “off”position.
3. Turn the white “down” limit switch (Fig. 2) one-quarter turn clockwise. Test by raising picture surface
approximately two feet, then lower again. Repeat until desired picture surface position is attained.
ADVANTAGE®DELUXE ELECTROL®INSTRUCTIONS
220 / 240V WIRING DIAGRAM
WITH ONBOARD LVC
120V WIRING DIAGRAM
WITH ONBOARD LVC
BLACK
WHITE
WHITE
RED (UP)
GRAY
BLACK (DOWN)
GREEN
DOOR SWITCH
SCREEN MOTOR
BLACK
WHITE
BLACK AND YELLOW
LOW-VOLTAGE
WALL SWITCH
BLACK
WHITE
RED
OPTIONAL RF OR IR
REMOTE CONNECTOR
LVC BOARD
WHITE (COMMON)
BLACK (DOWN)
RED (UP)
INPUT
GROUND
BLACK (HOT)
WHITE (COMMON)
120VAC 60HZ
INPUT
DOOR MOTOR
BLACK (CLOSE)
WHITE
RED (OPEN)
GREEN
DOWN
STOP
UP
BROWN
BLACK
BLUE
BLUE
BLACK (UP)
GRAY
BROWN (DOWN)
GREEN
DOOR SWITCH
SCREEN MOTOR
BROWN
BROWN AND
YELLOW
LOW-VOLTAGE
WALL SWITCH
AUX EYE
LVC BOARD
INPUT
GROUND
BLACK BROWN (HOT)
BLUE
BLACK
BROWN (DOWN)
BLACK (UP)
220/240VAC 50/60HZ
INPUT
DOOR MOTOR
BROWN (CLOSE)
BLUE
BLACK(OPEN)
GREEN
DOWN
STOP
UP
RED
NOTE: Electrical connections on left end of
case.
NOTE: Electrical connections on left end of
case.
BLACK
WHITE
RED
EYE AUX
OPTIONAL RF OR IR
REMOTE CONNECTOR
▲
!

4
ADVANTAGE®DELUXE ELECTROL®INSTRUCTIONS
RED
BLACK
WHITE
BLACK &
YELLOW
BLACK
GREEN
RED (UP)
BLACK (DOWN)
WHITE
GRAY
WHITE
RED
RED (UP)
BLACK (DOWN)
WHITE (COMMON)
AC (COMMON)
AC HOT
TO JUNCTION BOX MOUNTED IN SCREEN
CASE, IN WHICH INTERNAL WIRING TERMI-
NATES IN WHITE, RED AND BLACK LEADS.
BLACK
(DOWN)
BLACK WITH
YELLOW
RED
(UP)
UP
OFF
DOWN
OPERATING SWITCH,
SWITCH BOX, AND
PLATE FURNISHED
WITH SCREEN. (SPDT
WITH CENTER OFF)
SIDE VIEW OF
SWITCH & BOX
THIS SWITCH CANNOT BE USED WITH L.V.C.
NOTE: A SINGLE SWITCH CANNOT BE USED TO OPERATE MORE THAN ONE
SCREEN. CONTACT THE FACTORY FOR FURTHER INFORMATION.
IN MULTIPLE CONTROL INSTALLATIONS
THE SWITCH IS REPLACED BY THE LOW
VOLTAGE CONTROL, OPERATED FROM
PUSH BUTTON STATIONS.
115V. AC 60HZ.
1 AMP. MAX
DOOR SWITCH
BLACK
BLACK (CLOSE)
WHITE
RED (OPEN)
GREEN
SCREEN MOTOR
DOOR MOTOR
BLACK
BROWN
BLUE
BROWN &
YELLOW
BROWN
BROWN (DOWN)
BLACK (UP)
BLUE
GRAY
GREEN
BLUE
BLACK
TO JUNCTION BOX MOUNTED IN SCREEN
CASE, IN WHICH INTERNAL WIRING TERMI-
NATES IN BLUE, BROWN AND BLACK LEADS.
OPERATING SWITCH,
SWITCH BOX, AND PLATE
FURNISHED WITH
SCREEN. (SPDT WITH
CENTER OFF)
NOTE: A SINGLE SWITCH CANNOT BE USED TO OPERATE MORE THAN ONE
SCREEN. CONTACT THE FACTORY FOR FURTHER INFORMATION.
IN MULTIPLE CONTROL INSTALLATIONS
THE SWITCH IS REPLACED BY THE LOW
VOLTAGE CONTROL, OPERATED FROM
PUSH BUTTON STATIONS.
DOOR SWITCH
BROWN
BROWN (CLOSE)
BLUE
BLACK (OPEN)
SCREEN MOTOR
DOOR MOTOR
GREEN
NOTE:
MUST BE WIRED TO CONFORM TO
LOCAL WIRING CODE. THIS SWITCH
CANNOT BE USED WITH L.V.C.
220/240V. AC 50HZ.
2 AMP. MAX
POWER SOURCE
BLACK TO MOTOR
220 / 240V
WIRING DIAGRAM
120V WIRING DIAGRAM
NOTE: Electrical connections on left end of case.
NOTE: Electrical connections on left end of case.
BROWN TO MOTOR
BLUE TO MOTOR
BROWN (HOT)
YELLOW/GREEN (GROUND)
BLUE (COMMON)

5
ADVANTAGE®DELUXE ELECTROL®INSTALLATION
9-1/4"
(SUGGESTED) 3/8"
THREADED ROD (NOT
INCLUDED) ATTACHED
TO MOUNTING
BRACKET
FINISHED
CEILING
SELF-TRIMMING
FLANGE
7-1/4"
8-3/4"
CASE LENGTH
VARIABLE POSITION
MOUNTING BRACKETS
7-1/4"
6-1/8"
MOTOR END
6-1/8"
ELECTRICAL
JUNCTION BOX
SEE DETAIL A
(SUGGESTED) 3/8"
THREADED ROD
(NOT INCLUDED)
4.59"
7.21"
8.75"
DETAIL A
8.74"
HANGER BRACKET
7-1/4"
FLAT BAR MOUNTING METHOD
FORMED BRACKET
MOUNTING METHOD

6
TROUBLESHOOTING
SYMPTOM
1. Screen will not operate or will not go
“down”.
Motor does not hum.
Motor hums.
2. Screen will not move upward.
Motor does not hum.
Motor hums.
3. Door will not open.
CAUSE
(a) Incorrect line voltage.
(b) Blown facility fuse.
(c) Tripped facility circuit breaker.
(d) No power to operating switch or
junction box.
Power at junction box.
(e) Thermal overload tripped.
(f) Broken wire in the “down” position.
(g) Defective motor, limit switch or
capacitor.
(h) Capacitor burned out.
(a) Incorrect line voltage.
(b) Blown facility fuse.
(c) Tripped facility circuit breaker.
(d) No power to operating switch or
junction box.
(e) Open door limit switch.
Power at junction box
(f) Thermal overload tripped.
(g) Broken wire in the “up” position.
(h) Defective motor, limit switch or
capacitor.
(i) Capacitor burned out.
(a) Hinge is bound or has a foreign
substance on it which does not allow
it to open by gravity.
(b) No power.
SOLUTION
(a) Verify 115-125V (or 220-240V). If
insufficient voltage, rewire incoming
electric line.
(b) Replace facility fuse.
(c) Reset facility circuit breaker.
(d) Check above. Tighten all loose wire
connections. Recheck wiring. See
installation instructions.
“Down” Position
Check for power across black and white
leads.
(e) Let motor cool down for 15 minutes.
Try again.
(f) Check for continuity.
(g) Replace motor assembly.
NOTE: Motor is a sealed assembly.
(h) Replace motor assembly.
(a) Verify 115-125V (or 220-240V). If
insufficient voltage, rewire incoming
electric line.
(b) Replace facility fuse.
(c) Reset facility circuit breaker.
(d) Check above. Tighten all loose wire
connections. See above.
“Up” Position
Check for power across red and
white leads.
(e) Replace switch.
(f) Let motor cool down for 15 minutes.
Try again.
(g) Check for continuity.
(h) Replace motor assembly.
NOTE: Motor is a sealed assembly.
(i) Replace motor assembly.
(a) Check installation to free door. Clear
any foreign substance; i.e., paint or
plaster from hinge.
(b) See above.

Printed in U.S.A. 88584 Rev. 7/08
TROUBLESHOOTING
SYMPTOM
4. Door does not close.
5. “Down” limit switch incorrect.
6. Noise.
NOTE: Screen will operate with a low-
pitched hum.
7. Coasting.
8. Roller displaced from mounting
bracket.
9. Fabric hangs crooked.
10. Door closes before screen is all the
way up.
11. Door opens but screen does not
operate.
CAUSE
(a) Open door limit switch.
(b) No power from screen motor.
(a) “Down” limit switch out of
adjustment.
(a) Buzzing noise.
(b) Gear noise.
(a) Defective brake.
(a) Pin end slipped out of nylon bearing.
(a) Screen not installed properly.
(b) Fabric is damaged.
(a) Screen “up” limit out of adjustment.
(a) Loose wire.
SOLUTION
(a) Replace switch.
(b) Replace screen motor.
(a) See installation instructions.
(a) Adjust door limit switch (too far
down).
(b) Replace motor assembly.
(a) Replace motor assembly.
(a) Realign pin end bracket.
(a) Check for level and plumb.
(b) Replace fabric.
(a) Adjust “up” limit (call factory for
instructions).
(a) Check all wiring and connections.