Da-Lite Tensioned Cosmopolitan electrol User manual

DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: [phone]
800-622-3737
Fax: [phone]
Toll Free Fax: [phone]
www.da-lite.com
e-mail: [email protected]
Instruction Book for
TENSIONED COSMOPOLITAN® ELECTROL®
For Sizes Up To 10'x10'
The Da-Lite Difference.

1
IMPORTANT SAFETY INSTRUCTIONS
When using your video equipment, basic safety precautions should always be followed, including the
following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance
should be used. Cords rated for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this appliance. Contact an authorized
service dealer when repair work is required. Incorrect reassembly can cause electric shock when
the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the manufacturer may cause a risk of
fire, electric shock, or injury to persons.
SAVE THESE INSTRUCTIONS
PRE-INSTALLATION
INSTALLATION
There are three methods of mounting to include:
Flush against wall; Suspended from ceiling (use extension brackets); and Recessed above ceiling.
NOTE: Under no circumstances should unit be completely sealed in recessed installation. Allow access for service. Picture
surface is centered in case. Case extends 5-1/2" beyond surface on either end. Do not attach anything to screen slat rod
or bottom fabric pocket.
1. Make sure screen is level. Use a carpenter‘s level and plumb level.
CAUTION! Do not cut wrapping paper or tape with knife or any sharp tool. Remove by hand.
2. Install electrical hook-up that applies to your unit. Make sure to review your Electrical Installation Checklists and
Wiring Diagrams (included) for either 120 Volt Switch, 220/240 Volt Switch, or Low Voltage Control.
3. Test installation by running screen up and down a few times. Be prepared to stop screen. Standard Duty Cycle: 1
MIN. ON / 3 MIN. OFF.
NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC), CAN/
CSA C22.1 and the National Electric Code (NEC), NFPA 70.
1. Carefully unpack screen and remove outer wrapping from case.
2. Remove shipping brackets by removing the screws from the slat bar and wooden board.
3. Always handle screen in horizontal position.
PICTURE SURFACE PICTURE SURFACE PICTURE SURFACE
CEILING
MOUNTED
WALL MOUNTED
PICTURE SURFACE
CONCEALED (ALLOW ROOM FOR ACCESS)
USE No. 6 BRACKETS
TO HANG BEHIND
BEAM OR VALANCE

2
TENSIONED COSMOPOLITAN®ELECTROL®INSTALLATION
MOTOR
END
SLAT
3/4" DIAMETER HOLE FOR
WALL INSTALLATION
OVERALL LENGTH OF CASE
OVERALL LENGTH OF SLAT
BETWEEN HANGER EYES
PICTURE SURFACE
ENCLOSURE COVER
3/8" DIAMETER FOR
CEILING MOUNTING
7/8" DIAMETER OPENING
FOR ELECTRICAL SETTINGS
5 7/8"
1 7/8"
13/32"
4 5/8"
TO JUNCTION BOX, MOUNTED IN
SCREEN CASE, IN WHICH INTERNAL
WIRING TERMINATES IN WHITE,
BLACK AND RED LEADS
OPERATING SWITCH AND
PLATE FURNISHED WITH
SCREEN. (SPDT WITH
CENTER OFF)
SIDE VIEW
OF SWITCH
AND BOX
THIS SWITCH CANNOT BE USED WITH LVC.
NOTE: A single switch cannot be used to operate more than
one screen. Contact the factory for further information.
DOWN BLACK
BLACK
UP
WHITE
RED
DOWN
AC HOT
OFF
COMMON WHITE
BLACK WITH
YELLOW
UP RED
ROCKER
SWITCH
AC COMMON
120 V. 60 HZ. 2.5 MAX. AMP
120V WIRING DIAGRAM
DOWN
WHITE LIMIT
SWITCH
ADJUSTMENT
IN MULTIPLE CONTROL INSTALLATIONS
THIS SWITCH IS REPLACED BY THE LOW
VOLTAGE CONTROL, OPERATED FROM
PUSH BUTTON STATIONS.
WIRING ENCLOSURE COVER
240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH:
Da-Lite offers two styles of 240 volt wall switches for
standard operation. Please see wiring diagram included
in wall switch box included with screen.

3
TENSIONED COSMOPOLITAN®ELECTROL®INSTALLATION
120V WIRING DIAGRAM
WITH OPTIONAL BUILT-IN
LOW VOLTAGE CONTROL
GROUND–MUST BE
CONNECTED TO
BUILDING GROUND
RJ-14 PIN-OUTS
(TAB IS FACING UP)
IMPORTANT NOTE:
The wall switch is REQUIRED to make any limit switch
adjustments, EVEN if a third party control system is
used. Therefore, it is advised to wire the switch or
provide a 3-conductor connection that is accessible.
UP
STOP
DOWN
POWER INPUT 120VAC / 60HZ
GREEN (GROUND)
BLACK (HOT)
WHITE (COMMON)
POWER WIRE
DATA
CABLE
RJ-45 JACK
RJ-45
RECEPTACLE
RJ-22
OUTPUT
RJ-22
JACK
RJ-22
INPUTS
RJ-22
JACK
LED
UP LIMIT
TACTILE
BUTTON
DOWN LIMIT
TACTILE
BUTTON
FRONT OF
WALL SWITCH
BACK OF
WALL SWITCH
RJ-22 PIN-OUTS
(TAB IS FACING UP)
RJ-45 PIN-OUTS
(TAB IS FACING UP)
Standard RJ-22 can be used in place of RJ-14Supplied RJ-14 cable
BLUE
YELLOW
GREEN
RED
BLACK
WHITE
+12V
BUS (RP DATA)
RQ DATA
+5V
GND
RQ CLOCK
BUS (RP DATA)
RQ DATA
+5V
GND
WHITE
GREEN
RED
BLACK
BLUE
YELLOW
GREEN
RED
BLACK
ORANGE
BROWN
PURPLE
+12V
BUS (RP DATA)
RQ DATA
+5V
GND
RQ CLOCK
MANUAL 1
MANUAL 2
DRY CONTACTS
120V WIRING DIAGRAM WITH
OPTIONAL BUILT-IN VIDEO
PROJECTOR INTERFACE
5/12 VOLT SCREEN
TRIGGER ON PROJECTOR
CAUTION: THE PROJECTOR MUST BE TURNED OFF BEFORE CONNECTING THE
TRIGGER WIRES TO THE PROJECTOR. FAILURE TO DO SO MAY DAMAGE THE
CONTROLLER.
Use 2-conductor 20-24 gauge wire to extend the low voltage connection
from the projector’s 5 or 12-volt screen trigger output to the length
required to reach the VPI. When extending the low voltage connection
from the projector’s screen trigger output polarity does not matter. The
red and black wires from the VPI are interchangeable.
GROUND–MUST BE CONNECTED
TO BUILDING GROUND
UP
STOP
DOWN
POWER INPUT 120VAC / 60HZ
GREEN (GROUND)
BLACK (HOT)
WHITE (COMMON)
POWER
WIRE
DATA
CABLE
RJ-45
JACK
RJ-45
RECEPTACLE
RJ-22 OUTPUT
RJ-22 JACK
RJ-22
INPUTS
RJ-22
JACK
LED
UP LIMIT
TACTILE
BUTTON
DOWN
LIMIT
TACTILE
BUTTON
FRONT OF
WALL SWITCH
BACK OF
WALL SWITCH
BLACK
RED
VPI TRIGGER
MODULE
IMPORTANT NOTE:
The wall switch is REQUIRED to make any limit switch adjustments,
EVEN if a third party control system is used. Therefore, it is advised to
wire the switch or provide a 3-conductor connection that is accessible.
3-conductor 20-24 gauge wire can be used in place of the supplied RJ-14
cable to connect the wall switch. Connect the BUS terminals on the wall
switch to the corresponding BUS terminals on the splitter board.
UP
DOWN
COMMON
BUS
5V BUS
BUS
COM
5V
BUS
3-conductor 20-24 gauge wire can be used in place of
the supplied RJ-14 cable to connect the wall switch.
Connect the BUS terminals on the wall switch to the
corresponding BUS terminals on the splitter board.
DRY CONTACTS
UP
DOWN
COMMON
BUS
5V BUS
BUS
COM
5V
BUS

4
TENSIONED COSMOPOLITAN®ELECTROL®INSTALLATION
LOW-VOLTAGE WALL SWITCH
OPTIONAL IR AND RF
REMOTE CONTROL
MOTOR
BLUE (COMMON)
BROWN (HOT)
GREEN
GROUND TO CASE
240VAC 50HZ
240V WIRING DIAGRAM
WITH OPTIONAL BUILT-IN
LOW VOLTAGE CONTROL
RJ9
UP
STOP
DOWN
GROUND–MUST BE
CONNECTED TO
BUILDING GROUND
RJ9
GREEN
FRONT BACK
UP DN GND +5V
3-POSITION
SWITCH RJ9
ILT RJ9 PIN-OUTS
(TAB IS FACING UP)
IR or UP BLACK
GND COMMON RED
+5V GREEN
DN or DATA WHITE
DRY CONTACTS
SPLITTER
UP +5V COM DN
IMPORTANT NOTE: The wall switch is REQUIRED to make any limit
switch adjustments, EVEN if a third party control
system is used. Therefore, it is advised to wire the
switch or provide a 4-conductor connection that is
accessible.
CONNECT SUPPLIED
RJ9 CABLE TO
SPLITTER AND
SWITCH, OR USE 4
CABLE CONDUCTOR
TO CONNECT TO
SCREW TERMINALS.
The screen surface travel is stopped automatically in the fully opened and closed positions by limit switches that are
properly adjusted at Da-Lite. The screen should not be adjusted for more or less drop. The fabric cables are adjusted for
proper vertical and lateral tension at Da-Lite.
SCREEN ADJUSTMENT
CONTACT DA-LITE AT 800-622-3737 OR 574-267-8101 IF SCREEN MOTOR NEEDS ADJUSTMENT.
s
!

5
TROUBLESHOOTING
SYMPTOM
1. Screen will not operate.
Motor does not hum.
Motor hums.
2. Incorrect stopping position in
downward direction.
3. Incorrect stopping position in
upward direction.
4. Noise.
NOTE: Screen will operate with a
low pitched hum.
5. Coasting.
6. Roller displaced from mounting
bracket.
CAUSE
(a) Incorrect line voltage.
(b) Blown fuse.
(c) Tripped circuit breaker.
(d) No power to operating switch
or junction.
Power at junction box
(e) Thermal overload tripped.
(f) Broken wire in the “up” or ”down”
position.
(g) Defective motor, limit switch or
capacitor.
(h) Temporary binding.
(i) Capacitor burned out.
(a) “Down” limit switch out of
adjustment
(a) “Up” limit switch out of
adjustment
(a) Gear noise.
(a) Defective brake.
(a) Pin end slipped out of nylon
bearing.
SOLUTION
(a) Verify 115-125V (or 220-240V). If
insufficient voltage, rewire
incoming electric line.
(b) Replace fuse.
(c) Reset circuit breaker.
(d) Check above. Tighten all loose
wire connections. Correct any
improper connections.
“Down” Position
Check for power across black
and white leads.
“Up” Position
Check for power across red
and white leads.
(e) Let motor cool down for 15
minutes. Try again.
(f) Check for continuity. Cut off old
splice and reconnect.
(g) Replace motor assembly.
NOTE: Motor is a sealed assembly.
(h) With power “off”, turn roller by
hand to free binding.
(i) Replace motor assembly.
(a) Contact Da-Lite at 800-622-3737
or 574-267-8101.
(a) Contact Da-Lite at 800-622-3737
or 574-267-8101.
(a) Replace motor assembly.
(a) Replace motor assembly.
(a) Realign pin end bracket.
Visit www.da-lite.com/products/tutorials.php to find installation and troubleshooting tutorials. You will also
find a link to Live Chat for interactive support and you can contact us by email at [email protected] or by phone
at [phone] or [phone] with any troubleshooting questions.

6

7
Printed in U.S.A. 76063 Rev. 3/11
LIMITED ONE YEAR WARRANTY
ON DA-LITE PRESENTATION PRODUCTS
Da-Lite Screen Company, Inc. warrants its products to the original purchaser only, to be free from
defects in materials and workmanship for a period of one (1) year from the date of purchase by
the original purchaser provided they are properly operated according to Da-Lite’s instructions and
are not damaged due to improper handling or treatment after shipment from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental
damage, or which has been tampered with or repaired by a person other than authorized Da-Lite
personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option)
the defective part of the merchandise. Returns for service should be made to your Da-Lite dealer.
If it is necessary for the dealer to return the screen or part to Da-Lite, transportation expenses
to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in
shipment. To protect yourself against damage or loss in transit, insure the product and prepay all
transportation expenses.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY. Any implied
warranties of fitness for use, or merchantability, that may be mandated by statute or rule of law
are limited to the one (1) year warranty period. This warranty gives you specific legal rights, and
you may also have other rights, which vary from state-to-state. NO LIABILITY IS ASSUMED
FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF
EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY
NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite product, you may
contact our Sales Partners at PO Box 137, Warsaw, IN 46581-0137, [phone], [phone].
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE SHALL NOT BE
BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH
DA-LITE’S WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.