Dacor Millennia ETT304-1 Technical manual

PLANNING
GUIDE
www.Dacor.com
Phone: [phone]
Specications are subject to change without notice.
See installation instructions for additional details. 3.1
30 Inch and 36 Inch Wide,
Millennia®Electric Cooktops
PRODUCT DIMENSIONS - ETT365-2 AND METB365-1
(ETT365-2 SHOWN)
36 1/4" *
(921 mm)
34 3/8"
(873 mm)
19 3/8"
(495 mm)
21 1/4" *
(540 mm)
4" (102 mm)
Chassis height
30 1/4" *
(768 mm)
28 3/8"
(721 mm)
19 3/8"
(495 mm)
21 1/4" *
(540 mm)
4" (102 mm)
Chassis height
PRODUCT DIMENSIONS - ETT304-1 AND MET304
(ETT304-1 SHOWN)
ETT304-1, ETT365-2, MET304 and METB365-1
Product tolerances: ±1/16” (±1.6 mm) unless otherwise noted
Document # PG03 - 001 Revised 08/20/09 Page 1/3
NOTES:
The cooktop is supplied with a flexible, 48 inch long1.
power conduit consisting of two (2) insulated hot lead
conductors (L1 and L2) and one (1) insulated ground
conductor. There is no neutral connection. All leads are
copper. The conduit is connected to the right corner of
the cooktop. Do not connect the ground wire to neutral.
Tested in accordance with the latest edition of ANSI2.
Z21.1 and U.L. 858 Standard for household cooking
appliances.
These cooktops are not approved for recessed3.
installation.
Model No. Electrical Circuit Required Total Connected
Load*
Minimum Supply Wire Size
Line and Ground Connections
ETT304-1 240 Vac, 60 Hz, 40 Amps. 6.9 kW (29 Amps.)
No. 8 AWG
ETT365-2 240 Vac, 60 Hz, 40 Amps. 9.1 kW (38 Amps.)
MET304 240 Vac, 60 Hz, 40 Amps. 6.9 kW (29 Amps.)
METB365-1 240 Vac, 60 Hz, 50 Amps.* 9.6 kW (40 Amps.)
* For reference only, See the product data label on bottom of unit for exact specifications.
ELECTRICAL SUPPLY REQUIREMENTS
WARNING
Observe all governing codes and ordinances during planning•
and installation. Contact your local building department for
further information.
This appliance must be installed in accordance with the•
accompanying installation instructions.
* For units with stainless steel trim, other units may be up to 1/8" less.

PLANNING
GUIDE
www.Dacor.com
Phone: [phone]
Specications are subject to change without notice.
See installation instructions for additional details. 3.2
30 Inch and 36 Inch Wide,
Millennia®Electric Cooktops
ETT304-1, ETT365-2, MET304 and METB365-1
All tolerances: +1/16”, -0, (+1.6 mm, -0) unless otherwise stated
Document # PG03 - 001 Revised 08/20/09 Page 2/3
When installing model ETT365-2 or METB365-1 and the bottom of the chassis is
to be enclosed wall to wall, you must install Dacor ventilation duct kit ATD323.
Allow a minimum of 6 inches (152 mm) clearance between
the top of the countertop and any combustible surface
below, including the upper edge of a drawer below the
cooktop. Proper under-cabinet clearance is also required
for the cooktop hold down brackets.
6” (152 mm)
Min. clearance
to combustible
surfaces
A
6" (152 mm) Min.
from mounting surface to
combustibles below
cooktop chassis
B
Min. overhang,
both sides
Rear
wall
1" Min.
19 3/4" Min.
(502 mm)
1" (25 mm)
(25 mm)
1" Min.
(25 mm)
UNDER COUNTER CLEARANCE
Model A - Minimum Under Counter
Clearance (Width)
ETT304-1, MET304 30 1/2” (775 mm)
ETT365-2, METB365-1 36 1/2” (927 mm)
Model B - Minimum Under Counter
Clearance (Width)
ETT304-1, MET304 28 3/4” (730 mm)
ETT365-2, METB365-1 34 3/4” (883 mm)
COUNTERTOP CUTOUT (WITHOUT RAISED VENT)
3/4”
7 3/4” X 4 3/8”ventilationcut-outsinenclosureoor
1 1/2”1 1/2”
3/4”
TOP VIEW VENTILATION CUTOUT
Cooktop cutout in
top of cabinet

PLANNING
GUIDE
www.Dacor.com
Phone: [phone]
Specications are subject to change without notice.
See installation instructions for additional details. 3.3
30 Inch and 36 Inch Wide,
Millennia®Electric Cooktops
Stiffener
Cabinet face
Countertop
Floor
3/8” Min. (10 mm) space
behind raised vent
chassis to clear stiffener
3/8” Min. (10 mm)
flat countertop overhang
required behind cutout
ERV or PRV series raised
vent: Check raised vent
dimensions/specifications
to determine proper fit
ETT or MET series cooktop
19 3/4"
(502 mm)
1" Min.
(25 mm)
1" Min.
(25 mm)
1" Min.
(25 mm)
Cabinet
face
A
B
C
DE
6" (152 mm) Min.
from mounting surface to
combustibles below
cooktop chassis
Rear
wall
Stiffener
Cabinet face
Countertop
Floor
5/8” Min. (16 mm) space
behind raised vent
chassis to clear stiffener
5/8” Min. (16 mm)
flat countertop overhang
required behind cutout
RV series raised vent:
Check raised vent
dimensions/specifications
to determine proper fit
ETT or MET series cooktop
ERV AND PRV SERIES RAISED VENT INSTALLATION
SIDE VIEW
RV SERIES RAISED VENT INSTALLATION
SIDE VIEW
COUNTERTOP CUTOUT (WITH RAISED VENT)
TOP VIEW
COUNTERTOP CUTOUT (WITH RAISED VENT)
ISO VIEW
ETT304-1, ETT365-2, MET304 and METB365-1
All tolerances: +1/16”, -0, (+1.6 mm, -0) unless otherwise stated
Document # PG03 - 001 Revised 08/20/09 Page 3/3
Model/Configuration A - Cooktop
Cutout Width
B - Raised Vent
Cutout Width
C - Total Cutout
Depth
D - Raised Vent
Cutout Depth
E - Minimum
Rear Countertop
Overhang
ETT304-1 or MET304 cooktop with ERV30
or PRV30 raised vent 28 3/4”
(730 mm)
27 3/4”
(705 mm)
22 1/2”
(572 mm)
2 3/4”
(70 mm)
3/8”
(10 mm)
ETT304-1 or MET304 cooktop with
RV30 raised vent
22 1/4”
(565 mm)
2 1/2”
(64 mm)
5/8”
(16 mm)
ETT365-2 or METB365-1 cooktop with
ERV36 or PRV36 raised vent 34 3/4”
(883 mm)
33 3/4”
(857 mm)
22 1/2”
(572 mm))
2 3/4”
(70 mm)
3/8”
(10 mm)
ETT365-2 or METB365-1 cooktop with
RV36 raised vent
22 1/4”
(565 mm)
2 1/2”
(64 mm)
5/8”
(16 mm)