Dahua VTO6 series User manual

Digital Villa VTO (VTO6 Series)
Installation Guide
V2.0.2

Important Safeguards and Warnings
Please read the following safeguards and warnings carefully before using the product in
order to avoid damages and losses.
Note:
Do not expose the device to lampblack, steam or dust. Otherwise it may cause
fire or electric shock.
Do not install the device at position exposed to sunlight or in high temperature.
Temperature rise in device may cause fire.
Do not expose the device to humid environment. Otherwise it may cause fire.
The device must be installed on solid and flat surface in order to guarantee
safety under load and earthquake. Otherwise, it may cause device to fall off or
turnover.
Do not place the device on carpet or quilt.
Do not block air vent of the device or ventilation around the device. Otherwise,
temperature in device will rise and may cause fire.
Do not place any object on the device.
Do not disassemble the device without professional instruction.
Warning:
Please use battery properly to avoid fire, explosion and other dangers.
Please replace used battery with battery of the same type.
Do not use power line other than the one specified. Please use it properly.
Otherwise, it may cause fire or electric shock.
Special Announcement
This manual is for reference only.
All the designs and software here are subject to change without prior written
notice.
respective owners.
If there is any uncertainty or controversy, please refer to the final explanation
of us.


Table of Contents
1 System Networking...........................................................................................................4
1.1 One-to One Scene .................................................................................................4
1.2 One-Multiple Scenes..............................................................................................4
1.3 Group Call Scene...................................................................................................4
2 Install VTO........................................................................................................................6
2.1Model List ................................................................................................................6
2.2 Screw......................................................................................................................6
2.3 VTO6000A..............................................................................................................7
2.4 VTO6110B/VTO6210B/VTO6110BW.....................................................................8
2.5 VTO6000C/VTO6000CM/VTO6100C ..................................................................11
2.6 Electric Control Lock and Electromagnetic Lock..................................................13
3 Installation Debugging....................................................................................................16
3.1 Requirement for Power ........................................................................................16
3.2 On and Off............................................................................................................16
3.3 Debug Network.....................................................................................................16
4 Operation........................................................................................................................18
4.1 WEB Setup...........................................................................................................18
4.2 Issue Card............................................................................................................20
4.3 Group Call ............................................................................................................20
5 FAQ.................................................................................................................................24
Appendix 1.........................................................................................................................25
Appendix 1.1 Cable Specification...............................................................................25
Appendix 1.2 Power Extension Line Specification.....................................................25
Appendix 1.3 Embedded Box.....................................................................................25
Appendix 2 VTMS..............................................................................................................26
Appendix 3 VTMS Client....................................................................................................28
Appendix 3.1 Config Network Address.......................................................................28
Appendix 3.2 Create Organization.............................................................................30

1 System Networking
This chapter mainly introduces usage of digital VTO, please read the following content
and install the device according to your actual condition.
1.1 One-to-One Scene
Visitor press Call button to call residence (as VTH) or Center.
The following makes VTO6110BW as example. See Figure 1- 1.
Figure 1- 1
1.2 One-Multiple Scenes
In general, user installs VTO at entrance of building, and installs VTH in resident’s room.
Visitor can call any resident via the VTO, and the resident being called can unlock to allow
the visitor entering the building. Then, the visitor call the resident to unlock room door
again via second-confirm VTO.
1.3 Group Call Scene
About group call, please refer to Ch 4.3. See Figure 1- 2.

Figure 1- 2

2 Install VTO
2.1 Model List
This manual is for the following models; please carefully check your product model and its
function.
Product Model
Enclosure
Material
Color
IC Card
Unlock
Button
Lock Control
Module
VTO6000A
Metal
Metal
Gray
Not support
Mechanical
External
VTO6110B
Fireproof
ABS
Black
Support
Touch
External
VTO6110BW
Fireproof
ABS
White
Support
Touch
External
VTO6210B
Fireproof
ABS
Black
Support
Touch
Built-in
VTO6100C
Fireproof
ABS
White
Support
Mechanical
Built-in
VTO6000C
Fireproof
ABS
White
Not support
Mechanical
Built-in
VTO6000CM
Metal
Metal
Gray
Not support
Mechanical
Built-in
2.2 Screw
Before you install the VTO, please check screws in accessories bag and install according
to this manual.
Component Name
VTO6000A
Purpose
ST3×10 Cross recessed countersunk
head tapping screws—galvanizing
black
1
Fix unit and embedded
box
Component Name
Figure
VTO6000C,
VTO6000CM
VTO6100C
VTO6110B,
VTO6110BW
M3×8 Cross recessed countersunk head
tail machine screws --- galvanizing black
1
1

M4×30 Cross recessed countersunk head
tail machine screws
2
2
ST3×18 Cross recessed countersunk head
tail tapping screws --- galvanizing white
2
4
White expansion tube ￠6×30mm
2
4
2.3 VTO6000A
2.3.1 Dimension
Before you install the device, please make sure you know the dimension
of device and select appropriate installation method. See Figure 2- 1.
Figure 2- 1
2.3.2 Installation Step
Step 1. Install metal bracket into the groove on wall.
Step 2. Fasten ③onto the metal bracket along device chassis and bracket chassis (④
in Figure 2- 2).
Step 3. Lock screw a (ST3×10 Cross recessed countersunk head tapping screws), and
fix device unit onto the metal bracket.

Figure 2- 2
2.3.3 Wiring
See Figure 2- 3.
Figure 2- 3
No.
Port Name
Note
01
Power
Input DC 12V
02
Lock Port
Connect access control extension module
03
Network Port
1
Plug in RJ45 cable
2.4 VTO6110B/VTO6210B/VTO6110BW
2.4.1 Dimension
Before you install the device, please make sure you know the dimension of device and

select appropriate installation method. See Figure 2- 4.
Figure 2- 4 VTO6110B/VTO6210B/VTO6110BW
2.4.2 Installation Step
Here makes VTO6210B as an example. Installation of VTO6110B and
VTO6110BW may refer to VTO6210B.
Step 1. Fix installation bracket on wall.
a) Use M4 screw in accessories, to fix bracket onto 86 box (b in Figure 2- 5).
b) After 86 box is locked, fix ST3.0 screw in accessories onto wall. (c in Figure 2- 5)
Step 2. Fix device unit ①onto installation bracket, fasten top edge and lightly push
bottom edge.
Step 3. Use M3 screw to fix device and bracket.

Figure 2- 5
2.4.3 Wiring
This chapter introduces wiring between VTO embedded box and por.t
See Figure 2- 6.
VTO6110B, VTO6110BW
Figure 2- 6
No.
Port Name
Note
01
Power
Input DC 12V
02
Lock Port
Connect access control extension module
03
Network Port
1
Plug in RJ45 cable
VTO6210B

Figure 2- 7
No.
Port Name
Note
01
10-Pin Port
Connect to door lock, door sensor and unlock button.
It provides preserved 485 port for other devices.
02
Power
Input DC 12V
03
Network Port
1
Plug in RJ45 cable
2.5 VTO6000C/VTO6000CM/VTO6100C
2.5.1 Dimension
Before you install the device, please make sure you know the dimension of device and
select appropriate installation method. See Figure 2- 8.
Figure 2- 8
2.5.2 Installation Step

Figure 2- 9
Step 1. Remove M3 screw at the bottom of VTO, take down decoration cvoer ①.
Step 2. Fix the VTO onto wall, use M4 screw in accessories to fix the bracket onto 86
box (③in Figure 2- 9).
Step 3. b is designed to fasten the product.After 86 box is locked, Fix ST3.0 screw on to
wall (c in Figure 2- 9).
Step 4. Place decoration cover ①on to device unit ②, fix with MS screw.
Note:
Do not install VTO6100C on iron gate, otherwise the signal may be masked.
2.5.3 Wiring
This chapter taks VTO6100C as example since VTO6000C, VTO6000CM and
VTO6100C’s rear ports are the same. See Figure 2- 10.
Figure 2- 10
No.
Port Name
Note

1
Network Port
Plug in RJ45
2
3-pin Green
Port 1
Insert lock
3
3-pin Green
Port 2
Insert door sensor and unlock button
4
Power Port
DC 12V
5
Debug Port
For installer use
2.6 Electric Control Lock and Electromagnetic Lock
This chapter introduces VTO connection to electronic control loch and electromagnetic
lock.
2.6.1 Electric Control Lock
Here makes VTO6100C as an example. For VTO6000C, VTO6000CM and
VTO6100C you can refer to this chapter.
When VTO connects to electric control lock, it means that the positive end of
electronic control lock connects to NO of VTO (03.3-pin green 1) while its negative
end connects to COM of VTO (03.3-pin green 3).
When VTO connects to unlock button, one end of unlock button connects to ALM2 of
VTO (04.3-pin green 2) while the end connects to CND of VTO (04.3-pin green 3).
See Figure 2- 11.
Figure 2- 11
Here makes VTO6210B as an example.
When VTO connects to electric control lock, it means that the positive end of
electronic control lock connects to NO of VTO (RS485 port 2) while its negative end
connects to COM of VTO (RS485 port 1).
When VTO connects to unlock button, one end of unlock button connects to ALM1 of

VTO (RS485 port 5) while the end connects to GND of VTO (RS485 port 4). See
Figure 2- 12.
Figure 2- 12
2.6.2 Electromagnetic Lock
Here makes VTO6100C as an example. For VTO6000C, VTO6000CM and
VTO6100C you can refer to this chapter.
When VTO connects to electromagnetic lock, it means that the positive end of
electromagnetic lock connects to NC of VTO (03.3-pin green 2) while its negative end
connects to COM of VTO (03.3-pin green 3).
When VTO connects to door sensor in electromagnetic lock, one end of door sensor
connects to ALM1 of VTO (04.3-pin green 1) while the end connects to GND of VTO
(04.3-pin green 3). See Figure 2- 13.
Figure 2- 13
Here makes VTO6210B as an example.
When VTO connects to electromagnetic lock, it means that the positive end of

electromagnetic lock connects to NC of VTO (RS485 port 3) while its negative end
connects to COM of VTO (RS485 port 1).
When VTO connects to door sensor in electromagnetic lock, one end of door sensor
connects to ALM2 of VTO (RS485 port 6) while the end connects to GND of VTO
(RS485 port 4). See Figure 2- 14.
Figure 2- 14

3 Installation Debugging
Warning:
Before debugging, the staff shall be familiar with device’s installation, wiring
and usage.
Beore debugging, check wiring for short or open circuit.
When staff find each circuit is normal, plug the device to power.
After debugging, clear the site.
3.1 Requirement for Power
After installation is complete, first make sure devce power, current, wiring are right, then
plug device to power.
3.2 On and Off
After plugging device to power, you can turn on the device.
VTO6110B/VTO6110BW/VTO6210B
After power is pluggin in, indicators in button area light up and about 60s later they
turn off. Now systen enters normal working status.
VTO6000C, VTO6000CM and VTO6100C
After power is pluggin in, indicators in button area turn blue and about 60s later they
turn off. Now systen enters normal working status and the indicators remains blue.
3.3 Debug Network
First check if network is connected. In Internet Explorer’s address field, input IPaddress of
the VTO. If you can successfully login its WEB interface as in Figure 3- 1, it means the
network works properly.
Note:
Default IP address of VTO is 10.22.5.189 or 192.168.1.110. Default username and
password is admin/admin.After first login, please change your password.

Figure 3- 1

4 Operation
4.1 WEB Setup
If you first use VTO, you may need to operate according to the following steps:
Login WEB
First, make sure your PC and the VTO are well connected, and follow steps below to login
WEB interface.
Step 1. In Internet Explorer, input IP address of the VTO, and press Enter. System shows
Figure 4- 1.
Step 2. Input Username and Password.
Step 3. Click on Login.
Note:
Default IP address of VTO is 10.22.5.189 or 192.168.1.110. Default username and
password is admin/admin.After first login, please change your password.
Figure 4- 1
Setup
Step 1. In WEB interface, select System Config>Local Config, set video format as
WVGA as in Figure 4- 2.
Figure 4- 2

Step 2. In System Time tab, click on Sync PC to make VTO time the same with PC.
Step 3. Select System Config>Network Config, set VTO IP, Subnet Mask and Default
Gateway. See Figure 4- 3.
Figure 4- 3
Step 4. (Optional) If VTO connects to VTMS platform, System Config>LAN Config, set
Area No. Section No. Building No. And etc. These parameters must match settings
on VTO as in Figure 4- 4. Please refer toAppendix 2 and 3. See Figure 4- 5.
Figure 4- 4

Figure 4- 5
4.2 Issue Card
Issue Card on WEB
In WEB interface, click on Issue Card, and when you hear a “DI”sound, it means you have
successfully issued card. Then, you can swipe this card to unlock.
(VTO6000A/VTO6110B/VTO6110BW require access control module)
Issue Card by VTMS
Please refer to VTMS user’s manual.
4.3 Group Call
When guiest press Call button on VTO, multiple VTHs will ring. Resident can accept call,
hand up or unlock on any of these VTHs.
Note:
VTH includes main VTH and extension. In a system, there is no more than 1 main VTH
and 5 extensions. See Figure 4- 6.